USER’S GUIDE IP-011 Before printing read this guide.
Thank you very much for purchasing the IP-011. This User’s Guide includes instructions for making prints, correct handling of the machine, and precautions for safety. Please read this manual before printing. In order to maintain a satisfactory printing performance, please keep this Guide readily available for reference.
Introduction Make sure to read before use Thank you very much for purchasing the "Konica Printer Controller IP-011." Konica Corp. ("Konica") allows you to use the software attached to the IP-011 only when you agree to its "Software License Agreement." If you do not agree to terms of this agreement, return the software to the distributor from which you purchased it prior to use.
Introduction ■ Contents ■ ■ ■ ■ ■ ■ Contents .............................................................................................................................. ii Introduction ......................................................................................................................... v About Supplied Items .......................................................................................................... v About Positioning of This Manual ....................................
Introduction ■ Printer Driver Function List .............................................................................................. 3-5 ■ Description of Printer Driver Functions (in the alphabetic order) ..................................... 3-8 ● Alphabetic Order ................................................................................................................... 3-8 Driver Function Combination List .....................................................................................
Introduction Appendix A Troubleshooting .................................................... Appendix A-1 ■ Error Message ................................................................................................. Appendix A-2 ■ Basic Troubleshooting ...................................................................................... Appendix A-3 ■ General Problems of Printing ........................................................................... Appendix A-3 ● The “OHT Film” is not selectable.
Introduction ■ Introduction The IP-011 Printer Controller works as an interface between the Konica 7020 series Copier and a workstation, and enables direct printing from a workstation environment. The printer engine on the printer side and the optional network board include operating manuals (7020 series operating manual/KN-304 operating manual (CD)) respectively. For the detailed operations of Windows95/98 and Windows NT, refer to operating manuals of each operating system.
Introduction ● A part or all of this operating manual shall not be used or copied without permission. ● Konica shall have no liability for any influences caused by using the 7020 series copier +IP-011 system and this manual. ● Information written in this operating manual is subject to change without notice. ● Konica Corp. shall have the copyright of this printer driver. ● This printer driver shall not be copied except for the purpose of backup.
Introduction ■ About Positioning of This Manual This manual describes how to operate the Printer Controller Konica IP-011 when the Konica 7020 series copier is used as a printer by connecting it to computers or your network. An optional network board (KN-304) is required so as to use the Konica 7020 series copier as a printer by connecting it to your network.
Introduction ■ System Requirements ● Windows The following are required to print from the Windows*-compliant computers to the Printer Controller. • Computers on which Windows 95/98, WindowsNT 4.0 can run • CD-ROM drive (necessary to install the user software) In case of using Windows 95/98 • Microsoft Windows 95/98 • 32MB RAM or more In case of using Windows NT 4.0 • Microsoft Windows NT 4.
Introduction ■ Rules in This Manual • Notation of a name of each section in this manual It is written within [ ] (round brackets). (e.g. [Chapter 1: Outline ]) • Notation of names shown on the screen They are written within [ ](braces). (e.g. Click the [OK] button.) • Notation of cautions In this manual, important items to be paid attention to are written with marks. Each mark used in this manual has the following meaning. Precautions and limits at the time of operating hardware or software are written.
Chapter 1 Outline Chapter 1 Outline ■ Contents of This Chapter ............................................................ 1-2 ■ Outline of the Printer Controller .................................................. 1-3 ● IP-011 and Printer Engine ........................................................................... 1-3 ● IP-011 Hardware Configuration ................................................................... 1-4 ● I/O Interface ...............................................................
Chapter 1 Outline ■ Contents of This Chapter This chapter describes the outline of the Konica IP-011 Printer Controller. For the Copier, Konica 7020 series to which the Konica IP-011 Printer Controller is attached, refer to the operating manual of the Copier.
Chapter 1 Outline ■ Outline of the Printer Controller ● IP-011 and Printer Engine The Konica IP-011 is the Printer Controller (IP-011) which is used to connect the Copier, Konica 7020 series (Konica 7020 series) to computers or a network and to use the Konica 7020 series as a printer from applications on Windows 95/98 or Windows NT. To connect to a network, the optional Konica KN-304 network board is required.
Chapter 1 Outline ● IP-011 Hardware Configuration Basic Configuration Configuration of the IP-011 is as follows: Control board CPU: Power PC 401 GF Program memory: FLASH ROM System memory: 16MB SD-RAM Memory The IP-011 is equipped with 16 MB memory as standard and can be expanded to 80 MB at the maximum.
Chapter 1 Outline ● Data Flow Computer Printer Tools Application Status Monitor Control Panel Browser HTML IEEE1284 Network (TCP/IP,IPX/SPX) Printer Driver Spooler Interface IEEE1284 Network (TCP/IP,IPX/SPX) NIC Printer Controller IEEE1284 Intermediate Language Interpreter Memory IP-011 Command for Printing Image Data Engine Status Printer Engine PCI Bus E-RDH Memory Engine IP-011 Printer Controller 1-5
Chapter 1 Outline ● How to Use Memory Most of memory of the IP-011 is used for rasterizing images and a part of it is used for the system operation. In addition, E-RDH memory of the Konica 7020 series is used for print processing. The basic memory settings of the IP-011 is 16MB, which allows 1 bit mode (600 dpi) printing for all sizes of paper. The memory of the IP-011 can be expanded to 80MB at the maximum. In addition, the E-RDH memory of the Konica 7020 can be expanded to 288MB at the maximum.
Chapter 1 Outline ● General View The IP-011 is mounted to the Konica 7020 series. The following is the general view. IP-011 Parallel Port The IP-011 is attached to the back side of the Konica 7020 series.
Chapter 1 Outline ■ About the Printer Tools ● About the Printer Tools Install the printer driver into the computer system connected to the Konica 7020 + IP-011 series by using "Setup.exe" on the CD-ROM. During installation of the printer driver, you may simultaneously select installation of the Printer Tools, which is the generic name of two programs, "Status Monitor" and "Control Panel." The Printer Tools enable you to monitor the printer status from computers and to change printer settings.
Chapter 1 Outline ■ About the Printer Driver ● Compliant OS The printer driver can be used on the following OS. Windows 95 Windows 98 Windows NT 4.0 Windows 2000 (to be supported) Refer to “2 Setup” (2-1 page) for how to install the printer driver. Refer to “3 Printer Driver” (3-1 page) for detailed functions of the printer driver.
Chapter 2 Setup ■ Contents of This Chapter ............................................................ 2-2 ■ Installation of the Printer Driver................................................... 2-3 ● Before Installation ........................................................................................ 2-3 ● Files to be Installed ...................................................................................... 2-3 ● Installation to Windows95/98 ..................................................
Chapter 2 Setup ■ Contents of This Chapter To use the 7020 series +IP-011 system, connect the 7020 series +IP-011 system to computers by way of the parallel port and to install the printer driver to the computers. This chapter describes how to install the printer driver and how to print from applications. Refer to “Chapter 1 Outline” (1-7 page) for the detailed method of connecting to the parallel port. Refer to “Chapter 3 Printer Driver” (3-1 page) for functions of the printer driver.
Chapter 2 Setup ■ Installation of the Printer Driver ● Before Installation Models and Environment of Computers The Printer Controller for Konica 7020 series, IP-011, can be used with most computers ranging from personal computers to workstations. The IP-011 includes the printer driver for Windows95/98 and WindowsNT. The printer driver can be installed to any models of computers as long as Windows95/98 and WindowsNT have been installed to them.
Chapter 2 Setup ● Installation to Windows95/98 Perform the following steps to install the Konica IP-011 Printer Driver to Windows 95/98. Please keep the “User Software CD” on hand since it is required to install the printer driver. Installation with the “User Software CD” Turn on the computer and start Windows. When any Windows applications are active, exit from them. Set the “User Software CD” on the CD-ROM drive. Double-click the [My Computer] icon of the desktop to open the [My Computer] window.
Chapter 2 Setup The [Type of Connection] screen will appear. Then, select [Local] and click the [Next] button. When the Konica 7020 series Copier (IP-011) is directly connected to a computer to which the printer driver will be installed, select [Local]. In the case of selecting [Network] When personal computers or workstations are connected to the network and, you want to print by way of the network, connect to the optional network board (KN-304) and select [Network].
Chapter 2 Setup Installation by using [Add Printer] In this method, only the printer driver is installed. Turn on the computer and start Windows. When the Windows applications are active, exit from them. Click the [Start] button of the task bar. Then, select [settings] of the Start menu to click [Printers] from the sub-menu. The [Printers] window will open.
Chapter 2 Setup ● Installation to WindowsNT4.0 Only authorized system administrators or printer administrators should install the Konica IP-011 printer driver to WindowsNT4.0. Please keep the “User Software CD” on hand since it is required to install the printer driver. Printer Management on WindowsNT Since WindowsNT is an operating system made specially for the network operation, it is equipped with heavier security functions than other Windows.
Chapter 2 Setup Installation by Using the “User Software CD” Turn on the computer to start WindowsNT4.0. . Log on as an administrator (or a user entitled to install the Power User, etc.). . Set the “User Software CD” on the CD-ROM drive. Double-click the [My Computer] icon of the desktop to open the [My Computer] window, and double-click the active CD icon (user software CD). Opening from the start menu. Right-click the [Start] button of the task bar to click [Explorer].
Chapter 2 Setup The screen to select a port will appear. Then, select the port to which the Konica 7020 series Copier is connected and click the [Next] button. The [Printer Name] screen will appear. Then, specify the printer name and click the [Next] button. Default: [Konica IP-011] The [Select Destination Path] screen will appear. Select the location where you would like to install the component and click the [Next] button.
Chapter 2 Setup ● Uninstallation of the Printer Driver When any Windows applications are active, quit all of them. . Click the [Start] button of the task bar. Select [Settings] of the Start menu and click the [Control Panel] of the sub menu. The [Control Panel] window will open. Opening from [My Computer] You can open the [Control Panel] window by double-clicking the [Control Panel] folder after double cliking the [My Computer] icon of the desktop.
Chapter 2 Setup ■ Test Print You can check whether the printer driver functions properly by performing a test print after the printer driver has been installed. Click the [Start] button of the task bar. Then, select [Settings] of the Start menu and click [Printers] in the sub menu. The [Printers] window will open. Opening from [My Computer] You can open the [Printers] window by double-clicking the [Printers] folder after double clicking the [My Computer] icon of the desktop. .
Chapter 2 Setup ■ Print from Applications ● Execution of Printing Click the [File] menu of each application and click [Print]. . Check that [Konica IP-011] is shown on [Printer Name] and click [OK]. When [Konica IP-011] is not shown, select it from the list box. Setting the [Print] dialog box Refer to the user's manual of each application. Print settings of the printer driver Refer to “Print Settings” (2-12 page) for print settings of the printer driver.
Chapter 2 Setup Contents of Settings Details of each setting are described as follows; Items and their setting ranges shown on the screen and their descriptions are explained in detail. The underlined setting ranges indicate the default settings. [Setup] tab [Copies]: 1 to 999 Specifies the number of copies of the print job. [Orientation]: Portrait and Landscape Specified the print orientation. [Paper]-[Original Paper] Specified the original size set on the application.
Chapter 2 Setup [Image]-[Layout]: 1-Up, 2-Up, 4-Up, 8-Up and 9-Up Specifies how many pages of documents are gathered on one piece of paper. The default value, [1-Up(Default)], indicates that an one-page document is printed on one piece of paper. [Image]-[Print Page Borders]: Default value (not printing: without a check mark) Specifies whether borders are printed or not between documents when they are gathered on one piece of paper.
Chapter 2 Setup [Paper] tab [Front Cover]: On, Off, Blank and Printed Specifies whether a front cover is attached or not. Also specifies whether the front cover is blank or printed when it is attached. [Back Cover]: On, Off, Blank and Printed Specifies whether a back cover is attached or not. Also specifies whether the back cover is blank or printed when it is attached.
Chapter 2 Setup [Print Quality] tab [Smoothing]: Off, Type 1, Type 2 and Type 3 Type 1: processes suitable for oblique lines of general characters and pictures Type 2: processes suitable for curves of general characters Type 3: processes suitable for curves of decorated characters and fine characters [Page Protection]: Auto and On Specifies how to protect page data.
Chapter 2 Setup [Watermark] tab [Watermark String]: None, CONFIDENTIAL, COPY, DRAFT, FILE COPY, FINAL, PROOF, TOP SECRET Specifies the watermark. [First Page Only] Prints the watermark on the first page only. [Edit] Edits the watermark. (Refer to “[Edit/Add Watermark(Sub-Menu)] dialog box” on 2-18 page.) [Add] Adds new watermarks. (Refer to “[Edit/Add Watermark(Sub-Menu)] dialog box” on 2-18 page.) You can add up to 50 watermarks. [Delete] Deletes watermarks.
Chapter 2 Setup [Edit/Add Watermark(Sub-Menu)] dialog box [Edit Text] Specifies [Text], [Font], [Size] and [Style]. [Darkness] Specifies the darkness of the edit text. [Angle]: -90 degrees to +90 degrees Specifies the angle of the edit text. [Position]: Automatic centering and Manual positioning Specifies where on a page the edit text is put.
Chapter 3 Printer Driver Chapter 3 Printer Driver ■ Contents of This Chapter ........................................................... 3-2 ■ Working Environment ................................................................. 3-3 ● Compliant OS .............................................................................................. 3-3 ■ Property of Printer Driver ........................................................... 3-3 ■ Printer Driver Function List ......................................
Chapter 3 Printer Driver ■ Contents of This Chapter This chapter fully describes the functions of the Printer Driver installed in computers connected to the Konica 7020 series +IP-011 system. The Printer Driver functions are presented alphabetically in three parts, first listed, then described individually, then described in combination. Refer to “2 Setup” (2-1 page) for installation of the printer driver.
Chapter 3 Printer Driver ■ Working Environment ● Compliant OS The Printer Driver can be used on the following OS. Windows 95 Windows 98 Windows NT 4.0 Windows 2000 (to be supported) Refer to “2 Setup” (2-1 page) for installation of the Printer Driver. ■ Property of Printer Driver On the [Printer] window shown by clicking [Start]-[Settings]-[Printers], right-click the [KONICA IP-011] icon. When [Properties] is clicked on the shown menu, [KONICA IP-011 Properties] will appear.
Chapter 3 Printer Driver [Help] When the [Help] button is clicked, Help of each tab will appear. [General] tab Enables a print test of a printer. [Details] tab Performs settings related to ports, drivers, timeout and spooling. [Sharing] tab Performs share settings of a printer. [Setup] tab Performs settings related to Copies, Original size, Paper Size, Magnification, Paper Tray, Output Tray, Alternate, Sorting, Orientation, Layout, Staple and Duplex.
Chapter 3 Printer Driver ■ Printer Driver Function List The following list summarizes functions (Setting items) which can be set by using the Printer Driver of the Konica 7020 series +IP-011 system. Refer to “■ Description of Printer Driver Functions (in the alphabetic order)” (3-8 page) for setting items of each function. Refer to “■ List of Combined Printer Driver Functions (in the alphabetic order)” (3-23 page) for combination of each function.
Chapter 3 Printer Driver Classification Setting Items Set Value Description Konica Layout 1-Up (default): 2-Up, This function is used to print two pages, 4-Up, 8-Up and 9-Up four pages, eight pages or nine pages of documents on one piece of paper. On and Off This function is used to specify 7020 special functions Print page borders whether borders are printed or not between documents when they are gathered on one piece of paper.
Chapter 3 Printer Driver Classification Setting Items Set Value Description 95/98 Original paper A3, A4, A4R, A5R, B4 The original paper you can set differs B5, B5R, B6R, 8K, 16KR, 16K, F4, Ledger, Legal, depending on specifications in the country and trays. NT4.0 LetterR, Letter, Statement Paper size The same as The paper sizes you can set differ Original Paper depending on specifications in the country and trays. Refer to the operating manual of the copier for details.
Chapter 3 Printer Driver ■ Description of Printer Driver Functions (in alphabetic order) Functions (setting items) which can be set with the Printer Driver are summarized in the alphabetic order. These settings can be set by using [Start]-[Settings]-[Printers]- [KONICA IP-011] property. The tabs in this section are those in the [KONICA IP-011] property. ● Alphabetic Order A About When [Setup] tab-[About] button is clicked, version information of the Printer Driver is shown.
Chapter 3 Printer Driver B Back cover By using [Paper] tab-[Back Cover], you can perform the setting to use a designated tray for printing the last page. Select either [On] or [Off]. Default of Back Cover is [None]. When [On] is selected, select either [Blank] or [Printed]. When [Blank] is selected, nothing is printed on the back cover. When [Printed] is selected, the last page is printed on a back cover. The tray for the back cover is selected by using [Front/Back Cover]-[Paper Tray].
Chapter 3 Printer Driver Copies Click the [▲] or [▼] button beside [Setup] tab-[Copies] or directly enter the number of copies from the keyboard. Default of the number of copies is 1. D Default By clicking [Setup] tab-[Default] button, settings of the [Setup] tab, [Paper] tab, [Print Quality] tab, and [Watermark] tab return to defaults.
Chapter 3 Printer Driver Duplex printing By using [Setup] tab-[Duplex], you can perform settings of the Duplex printings. You can select [1-Sided], [2-Sided Short Edge Binding], [2-Sided Long Edge Binding] or [Booklet] from the list shown by clicking the [▼] button beside the [Duplex] box. Default of the Duplex printing is [1-Sided]. When [1-Sided] is selected, only one side of paper is printed.
Chapter 3 Printer Driver E End Capture When the virtual printer port is specified on the [End Capture] dialog shown by clicking [Details] tab-[End Capture] button, you can delete a network printer allocated as a virtual printer port. F Finisher When the Finisher is attached to the copier, you can select the Finisher setting from [None], [2 Trays], [3 Trays] or [4 Trays]. Default of the Finisher is [None].
Chapter 3 Printer Driver Front Cover [Off] Front Cover [On] [Blank] Front Cover [On] [Printed] [Not indicated] Front/Back Cover- Paper Tray Specify the tray for Front/Back Cover from the list shown by clicking the [▼] button beside the [Paper] tab-[Front/Back Cover]-[Paper Tray] button. The selection by using [Front/Back Cover]-[Paper Tray] must be different from that by using the [Setup] tab-[Paper Tray].
Chapter 3 Printer Driver [8-Up] [9-Up] When [Booklet] is selected in the Duplex printing, [2-Up] is automatically selected and you can not select other settings. When [Setup] tab-[Print Page Borders] check box is selected, you can print borders between gathered documents. Default of Print Page Borders is no check mark. When Layout is set to [1-Up], you can not select [Print Page Borders].
Chapter 3 Printer Driver Orientation Select either [Portrait] or [Landscape] from the list shown by clicking the [▼] button beside [Set up] tab-[Orientation] box. Default of Orientation is Portrait. Output tray Select an output tray from the list shown by clicking the [▼] button beside [Setup] tab[Output Tray] box. When [None] is selected in the Finisher settings, or When the Finisher is not installed, other settings than [Printer's Default] can not be selected.
Chapter 3 Printer Driver Paper type [Plain], [OHT Film], [OHT Interleave] or [OHT Interleave Printed] can be selected from the list shown by clicking the [▼] button beside [Paper] tab- [Paper Type] box. When Front/Back Cover is set, you can select only Plain. When [Tray 1], [Tray 2], [Tray 3] or [Tray 4] is selected by using [setup] tab-[Paper]-[Paper Tray], OHT Film is not shown on the list.
Chapter 3 Printer Driver Print using the following driver Select the driver used for printing from the list shown by clicking the [▼] button beside [Details] tab[Print using the following driver] box. When a driver is changed, settings of presently shown property are saved and the property of the newly selected driver will appear. S Set up-Original Paper Select the original paper from the list shown by clicking the [▼] button beside [Setup] tab-[Paper][Original Paper] box.
Chapter 3 Printer Driver Settings of the two-way communication function The [Spool Settings] dialog shown by clicking the [Details] tab-[Spool settings] button enables you to perform settings of spooling and the bidirectional communication function. When [Enable bi-derectional support for this printer] is selected, the bi-directional communication is performed. When [Disable bi-derectional support for this printer] is selected, the bi-directional communication is not performed.
Chapter 3 Printer Driver Spool settings Set the method of spooling (temporary saving) the print data when it is sent to the printer on the [Spool Settings] dialog shown by clicking [Detail] tab-[Spool Settings] button. When [Spool print jobs so program finishes printing faster] is selected, Spool is set to on by default. You may select either [Start printing after last page is spooled] or [Start printing after first page is spooled] as a method of spooling.
Chapter 3 Printer Driver In addition, when Staple is specified, you can’t select Alternate. You can’t staple at two positions for the paper of B5R or smaller. Stapling is performed in accordance with orientations as follows: 1- Left (portrait) 1- Right (portrait) 1- Left (landscape) 1-Right (landscape) 2-Left (portrait) 2-Left (landscape) 2- Top (portrait) 2-Top (landscape) T Timeout settings By using [Detail] tab-[Timeout Settings], the timeout value is set.
Chapter 3 Printer Driver W Watermark Selecting a watermark from the list of the [Watermark] tab enables you to print documents with a watermark. When the Printer Driver is installed, the basic watermarks are installed at the same time. In this condition, you can select a watermark from [NONE], [CONFIDENTIAL], [COPY], [DRAFT], [FILE COPY], [FINAL], [PROOF] and [TOP SECRET]. Default of watermark is [None].
Chapter 3 Printer Driver Driver Function Combination List Paper Type Paper Tray Tray 1 Tray 2 Tray 3 Tray 4 Bypass Paper Size Paper Tray Paper Type Output Tray Alternate Sorting Layout Print Page Borders Staple Duplex A3 A4R A4 A5R A5 A6 B4 B5R B5 B6R Ledger (11҂17) Legal(8.5҂14) LetterR(8.5҂11R) Letter(8.5҂11) Statement (5.5҂8.
Chapter 3 Printer Driver Alternate Paper Size Paper Tray Paper Type Output Tray Alternate Sorting Layout Print Page Borders Staple Duplex A3 A4R A4 A5R A5 A6 B4 B5R B5 B6R Ledger (11҂17) Legal(8.5҂14) LetterR(8.5҂11R) Letter(8.5҂11) Statement (5.5҂8.
Chapter 3 Printer Driver Duplex Paper Size Paper Tray Paper Type Output Tray Alternate Sorting Layout Print Page Borders Staple Duplex A3 A4R A4 A5R A5 A6 B4 B5R B5 B6R Ledger (11҂17) Legal(8.5҂14) LetterR(8.5҂11R) Letter(8.5҂11) Statement (5.5҂8.
Chapter 3 Printer Driver Front/Back Cover Paper Type Paper Size Paper Tray Paper Type Output Tray Alternate Sorting Layout Print Page Borders Staple Duplex Front Cover Back Cover Front/Back Cover Paper Tray Front/Back Cover Paper Type Finisher Option Tray Finisher Option Tray Plain Thick None 2 Trays 3 Trays 4 Trays None DB-209 DB-409 A3 쎻 쎻 쎻 쎻 쎻 쎻 쎻 쎻 쎻 A4R 쎻 쎻 쎻 쎻 쎻 쎻 쎻 쎻 쎻 A4 쎻 쎻 쎻 쎻 쎻 쎻 쎻 쎻 쎻 A5R 쎻 쎻 쎻 쎻 쎻 쎻 쎻 쎻 쎻 A5 ҂ ҂ 쎻 쎻 쎻 쎻
Chapter 4 Control Panel Setup ■ Contents of This Chapter ............................................................ 4-2 ■ About the Control Panel .............................................................. 4-3 ● The Control Panel of the Copier .................................................................. 4-3 ● How to Enter Settings on the LCD ............................................................... 4-4 ● Printer Mode Basic Screen ............................................................
Chapter 4 Control Panel Setup ■ Contents of This Chapter In this chapter describes the printer mode basic screen and the setup menu of the Copier Operation Panel. Refer to the operating manual of the copier for other functions and screens of the Control Panel.
Chapter 4 Control Panel Setup ■ About the Control Panel ● The Control Panel of the Copier SCANNER/PRINTER LED [SCANNER/PRINTER] button DATA LED SCANNER/PRINTER FAX COPY HELP 1 2 3 INTERRUPT CHECK 4 5 6 APPLICATION 7 8 STOP/ CLEAR 9 OUTPUT 0 START CLEAR QTY AUTO RESET [STOP/CLEAR] button [AUTO RESET] button LCD [Setting confirmation] button [SCANNER/PRINTER] button Switches to the printer mode.
Chapter 4 Control Panel Setup ● How to Enter Settings on the LCD Panel You can enter settings from the printer mode basic screen shown on the LCD by using either the item selection or the information entry. Item Selection In this method, various settings are performed by selecting a button with a number which corresponds to the item you would like to select on the LCD. Information Entry In this method, a printer name or a set value is entered by selecting alphabets or numbers shown on buttons of the LCD.
Chapter 4 Control Panel Setup ● Printer Mode Basic Screen When the Konica 7020 series +IP-011 system starts properly, the printer mode basic screen is displayed on the LCD by pressing the [SCANNER/PRINTER] button. ● Printer Menu Screen The following printer menu screen is displayed by pressing the [Setting] key on the printer mode basic screen. When the [SCANNER/PRINTER] button is pressed again, the LCD is changed to the copy mode basic screen, and the normal copy settings becomes available. [1.
Chapter 4 Control Panel Setup ● Printer Setting screen When “1. Setting” on the printer menu screen is selected, the Printer Setting screen is displayed. When an item is selected on the Printer Setting screen, each setting screen corresponding to the selected item is displayed. Buttons commonly used among setting screens are as follows: [Main Menu] Pressing the [Main menu] button returns to the printer menu screen.
Chapter 4 Control Panel Setup ● Procedures of the Printer Setting The following show the procedures of the printer setting by using the LCD Panel; Press the [SCANNER/PRINTER] button to show the printer mode basic screen. The copy mode basic screen is switched to the printer mode basic screen. Press the [Setting] key to show the printer menu screen. Press the numeric key [1] to select [1. Setting]. The printer mode basic screen is switched to the printer menu screen.
Chapter 4 Control Panel Setup Press the [Yes] button on the save preservation confirmation screen shown by pressing the [Main Menu] or [Previous] button to save new settings. Press the [No] button not to save the settings. Refer to “ Configuration of the Printer Setting Menu ” (4-9 page) for configuring the printer setting menu. Refer to “ Functions of the Printer Setting ” (4-11 page) for the printer setting details.
Chapter 4 Control Panel Setup ■ Configuration of Printer Setting Menu 1 Network Setup *This menu is displayed only when the KN-304 is attached. 1 TCP/IP Setup 1 Set IP Mode 1 Enable DHCP 2 Static IP Address 2 Set IP Manually 1 IP Address 3 LPD Banner Enable 2 Subnet Mask 3 Gateway 4 Persistent IP Address Enable 2 NetWare Setup 1 Server Name 2 Server Password 1 Yes 3 Queue Scan Rate 2 No 4 Frame Type 1 Auto 5 Disable Bindery 2 Ethernet 802.
Chapter 4 Control Panel Setup 3 Print Quality 1 Off 1 Smoothing 2 Type 1 3 Type 2 4 Type3 2 Page Protection 1 Auto 2 On 4 I/O Timeout 1 5 6 60 2 10 7 120 3 15 8 180 4 20 9 240 5 30 10 300 5 Test Print 1 Demo/Configuration Page 2 NIC Configuration 6 CMD Error Page 1 Off 2 On 7 Error Page 1 Off 2 On 8 Factory Default 9 Help 4-10 IP-011 Printer Controller
Chapter 4 Control Panel Setup ■ Functions of the Printer Setting ● Network Setup Select [1. Setting]-[1. Network Setup] on the Printer Setting screen to display the network setup screen. [1. Network setup] is displayed only when the KN-304 is attached. Items of the network setup screen are as follows: Refer to the operating manual of the KN-304 for details of the network connection. [1. TCP/IP Setup] Press [1] to display the TCP/IP Setup screen.
Chapter 4 Control Panel Setup ● Print Quality Select [1. Setting]-[3. Print Quality] on the Printer Setting screen to display the Print Quality Setup screen. Items of the Print Quality Setup screen are as follow: [1. Smoothing] Press [1] to display the Smoothing Setup screen. You can set to [Off], [Type 1], [Type 2] or [Type 3] on the Smoothing Setup screen. The factory default is [1. None]. [2. Page Protection] Press [2] to display the Page Protection Setup screen.
Chapter 4 Control Panel Setup ● Test Print Select [1. Setting]-[5. Test Print] on the Printer Setting screen to display the Test Print Setup screen. Items of the Test Print Setup screen are as follows: [1. Demo/Configuration Page] Press [1] to print the Demo/Configuration Page immediately.
Chapter 4 Control Panel Setup ● Factory Default Select [1. Setting]-[8. Factory Default] on the printer mode basic screen to return various settings to the factory default. Items of the Factory Default are as follows: [Language]: English [Smoothing]: Off [Page Protection]: Auto [I/O Timeout]: 30 *Refer to the operating manual of the KN-304 for details of Factory Default of the Network Setup. ● Help Select [1. Setting]-[9. Help] on the printer mode basic screen to display the help screen.
Chapter 5 Status Monitor and Control Panel ■ Contents of This Chapter ............................................................ 5-2 ■ Status Monitor and Control Panel ............................................... 5-3 ● About the Status Monitor ............................................................................. 5-3 ● About the Control Panel ............................................................................... 5-3 ■ Working Environment ..............................................
Chapter 5 Status Monitor and Control Panel ■ Contents of This Chapter Printer Tools is the generic name for two programs, "Status Monitor" and "Control Panel." This chapter describes how to use these programs on computers connected to the 7020 + IP-011 system. These programs enable you to monitor printer status and change printer settings.
Chapter 5 Status Monitor and Control Panel ■ Status Monitor and Control Panel The Printer Tools is the generic name of two programs, “Status Monitor” and “Control Panel” which are used on computers connected to the Konica 7020 series +IP-011 system. ● About the Status Monitor The Status Monitor is a program which enables you to monitor the printer status from computers connected to the Konica 7020 series+IP-011 system.
Chapter 5 Status Monitor and Control Panel ■ Working Environment ● Compliant OS The Status Monitor and the Control Panel can be used on the following OS. Windows 95 Windows 98 Windows NT4.0 Windows 2000 (to be supported) ● Interface The interface which the Status Monitor and the Control Panel use is as follows: IEEE 1284 (Compatible mode, Nibble and ECP) ■ How to Install When executing “setup.
Chapter 5 Status Monitor and Control Panel ■ How to Operate the Status Monitor ● Starting the Status Monitor If, at the time of installing the Printer Tools, Status Monitor is set to automatically start, the Status Monitor automatically starts when a computer starts. Immediately after the [Konica IP-011 Status Monitor] window has been displayed, the printer status is checked. ● Finishing the Status Monitor Click [View] menu-[Finish] on the [Konica IP-011 Status Monitor] window.
Chapter 5 Status Monitor and Control Panel ● Show/Hide the Status Monitor When the [Close] button is clicked when the Status Monitor is displayed, the Status Monitor is hidden (displayed as an icon on the task bar.). When the Status Monitor icon on the task bar is clicked when the Status Monitor is hidden, the Status Monitor is displayed. When an error occurs in communication with the printer, a confirmation message is displayed.
Chapter 5 Status Monitor and Control Panel ● Display Change Display of the Status Monitor can be selected from either [Expand] or [Reduce]. Normally, the Status Monitor starts in the [Reduce] display. In the [Expand] display, when a problem related to the printer occurs and information related to the problem is shown on the Status Monitor, the position of the problem is indicated by using an image and a method of recovery is displayed in the How to Recover list.
Chapter 5 Status Monitor and Control Panel ■ How to Operate the Control Panel ● Starting the Control Panel Select [Printer Setting] from the [Setup] menu of the Status Monitor window. The [Konica IP-011 Control Panel] dialog is displayed. ● Finishing the Control Panel Click the [OK] button to send data of settings to the printer. The [Konica IP-011 Control Panel] dialog is closed and the [Konica IP-011 Status Monitor] window is displayed. Click the [Cancel] button not to perform settings.
Chapter 5 Status Monitor and Control Panel ● Buttons of the Control Panel [OK] When the [OK] button is clicked, data of all settings of the tab is sent to the printer. Then, the [Konica IP-011 Control Panel] dialog is closed and the [Konica IP-011 Status Monitor] window is displayed. [Cancel] When the [Cancel] button is clicked, the [Konica IP-011 Control Panel] dialog is closed and the [Konica IP-011 Status Monitor] window is displayed.
Chapter 5 Status Monitor and Control Panel ● Settings of Paper Click the [Paper] tab of the [Konica IP-011 Control Panel] dialog. The [Paper] tab of the [Konica IP-011 Control Panel] dialog is displayed. On the list shown by clicking the [▼] button beside [Paper Size], [Paper Tray] and [Output Tray] of the [Paper] group box, select an item you desire respectively. Click either [Portrait] or [Landscape] from the [Orientation] group box.
Chapter 5 Status Monitor and Control Panel ● Printer Setting Click the [Printer Setting] tab of the [Konica IP-011 Control Panel] dialog. The [Printer Setting] tab of the [Konica IP-011 Control Panel] dialog is displayed. Click either [Auto] or [On] of the [Page Protection] group box. Select the desired item on the list shown by clicking the [▼] button of the [I/O Timeout] Group Box. The printer waits for entry of data during time (second) you selected in this box.
Chapter 5 Status Monitor and Control Panel ● Test Print Click the [Test Print] tab of the [Konica IP-011 Control Panel] dialog. The [Test Print] tab of the [Konica IP-011 Control Panel] dialog is displayed. Click the [Print Demo/Configuration Page] button to print the Print Demo/Configuration Page. Click the [Print NIC Status Page] button to print the Print NIC Status Page. Click the [OK] button. Click the [OK] button when you do not continue to perform settings of other tabs.
Appendix A Troubleshooting Appendix A Trouble Shooting ■ Error Message ........................................................... Appendix A-2 ■ Basic Troubleshooting ................................................ Appendix A-3 ■ General Problems of Printing ..................................... Appendix A-3 ● The “OHT Film” is not selectable. ................................................. Appendix A-3 ● The Printer Controller does not respond to the “Print” command. .................................
Appendix A Troubleshooting ■ Error Message The error messages shown on the Status Monitor are as follows: Error Message Mishandled paper in ADU DB Upper Tray is not ready DB Lower Tray is not ready Mishandled paper in DB Lower Tray No paper in DB Lower Tray DB Lower Tray is not available No paper in DB Upper Tray DB Upper Tray is not available DB door is open LCT is not ready Mishandled paper in LCT No paper in LCT LCT is not available Mishandled paper in RADF RADF Failure RADF Communication Error OverRun S
■ Basic Troubleshooting This section describes how to troubleshoot. If troubles are not removed by using the following countermeasures, contact a service provider. There are some basic conditions which cause various abnormalities. Before taking a trouble as a special case, first refer to the following basic countermeasures. Check the power of the copier and computers and cable connections. Check the LCD of the copier to find information concerning the current trouble.
Appendix A Troubleshooting ● A message to demand a paper size which you do not use is displayed. Cancel the job to change the paper size of “Page (Paper) Setup” dialog on an application. ● You can not print the test print Check the LCD of the copier Control Panel. When “Ready to copy” is displayed on the LCD, go to the Step 3. When a diagnosis message or an error message is displayed on the LCD, refer to the operating manual of the copier. When the LCD is blank, go to the Step 2.
● The print setting of a job does not correspond to the result of printing. Check that the printer setting is not changed. Refer to “5 Status Monitor and Control Panel” Printer Setting “(5-11 page) or ”3 Printer Driver “ Printer Driver Function List” for the printer setting.(3-5 page) ● The “Duplex” option is not displayed. Check that , [B6R] is not selected as a paper size. ● Memory Error / Memory Overflow / Overrun Set the Page Protection.
Appendix B Product Specifications Appendix B Product Specifications ■ Product Specifications ...............................................
Appendix B Product Specifications ■ Product Specifications Model: built in the Konica 7020 series Copier Paper You can select from the following paper sizes: Paper Sizes to Be Selected A3 A4 A4R A5R B4 B5 B5R B6R 8k 16k 16kR F4 Ledger Legal (8.5x14in) Letter (8.5x11in) LetterR (8.5x11in) Statement (5.5x8.5in) Paper Feeding and Amount of Feeding Paper: The same as the copier Load Output Paper: Mode: The same as the copier The dual operation of the Copier and the Printer is available.
Appendix B Product Specifications Network Interface (Option): KN304: Ethernet (100Base-T / 10Base-T) Protocol: IPX/SPX (NetWare) LPD/LPR (TCP/IP) Peer to Peer (TCP/IP) Compliant OS: Windows 95/98 Windows NT4.0 Windows 2000(to be supported) Printer Language: Destiny WinStylerNozomi Version 2.
index index index ........................................................................................
index index A About .............................................................. 3-8 Add Port ......................................................... 3-8 Allocate a printer port ..................................... 3-8 Alternate ......................................................... 3-9 B Back cover ...................................................... 3-9 Basic Troubleshooting .................... Appendix A-3 Booklet .........................................................
index Paper-Original Paper .................................... 3-16 Port settings ................................................. 3-16 Print page borders ....................................... 3-16 Print Quality ....................................... 4-10, 4-12 Print quality .................................................. 3-16 [Print Quality] tab ................................. 2-16, 3-4 Printer Driver Function List ............................. 3-5 Printer Engine ................................
MANUFACTURER KONICA CORPORATION TOKYO JAPAN 2000.
