i EP2010 Thank you for choosing Minolta. This operator’s manual explains how to operate the copier and replenish its supplies. It also gives some troubleshooting tips as well as general precautions to be observed when operating the copier. To ensure the best performance and effective use of your copier, read this manual carefully until yo u familiarize yourself thoroughly with its operation and features. After you have read through the manual, keep it for ready reference.
ii Contents Chapters 1 through 3 contain the basic information for making copies. Be sure to read these chapters before attempting to use your copier. Chapter 1 Safety Notes p. 1 1. Installing The Copier p. 2 Installation Site Power Source Space Requirements 2. Precautions for Use p. 3 Operating Environment Using the Copier Properly Moving Care of Copier Supplies Chapter 2 Getting to Know your Copier 1. System Overview p. 6 2. Copier Parts and Accessories Outside the Copier p. 8 Inside the Copier p.
iii Contents Chapter 3 Making Copies p. 19 1. Basic Copying Overview p. 20 2. Placing Originals • Placing on the Original Glass p. 22 • Using the Automatic/Duplexing Document Feeder p. 24 • Using the Mixed Original Detection Mode p. 25 • Using the Single Automatic Document Feeding Mode (SADF Mode) p. 26 ▲ ▲▲▲▲ 3. Manual Bypass Copying p. 28 4. Copy Paper Size p. 30 5. Zoom Ratio p. 32 6. Image Density p. 34 7. Original Copy Type p.
iv Contents Chapter 4 Special Functions p. 49 1. Meter Count p. 50 2. Toner Replenisher/Drum Dehumidifier p. 51 3. User’s Choice Description of Each User’s Choice Functions p. 52 Making the User’s Choice Settings p. 58 Chapter 5 When an Indicator Lights Up 1. 2. 3. 4. 5. p. 59 When the Add Paper Indicator Lights Up p. 60 When the Add Toner Indicator Lights Up p. 63 When the Add Staple Indicator Lights Up p. 64 When the Closure Failure Indicator Lights Up p.
v Contents Chapter 6 Troubleshooting p. 85 1. When this Type of Copy is Produced p. 86 • The image is too light • The image is too dark • The copy is blurry • The copy has dark specks or spots • The edge of the copy is dirty • The image on the copy is not aligned properly • The copy has lines Safety Notes Chapter 2 2. The Copier is not functioning as designed p.
1 Safety Notes Chapter 1 Chapter 1 1. Installing the Copier p. 2 Installation Site Power Source Space Requirements 2. Precautions for Use p. 3 Operating Environment Using the Copier Properly Moving Care of Copier Supplies Safety Notes This chapter explains about the operating environment, conditions, and precautions for use.
2 1. Installing the Copier Installation Site A place away from a curtain or the like that may catch fire and burn easily. ◆ An area where there is no possibility of being splashed with water or other types of liquid. ◆ An area free from direct sunlight. ◆ A place out of the direct air stream of an air conditioner, heater, or ventilator. ◆A well-ventilated place. dry place. ◆ A dust-free location. ◆ An area not subject to undue vibration. ◆ A stable and level location.
3 2. Precautions for Use Operating Environment Temperature Humidity : 10°C to 35°C (50°F to 86°F) with a fluctuation of 10°C (50°F) per hour. : 15% to 85% with a fluctuation of 20% per hour. Using the Copier Properly Chapter 1 The operating environmental requirements of the copier are as follows. NEVER place a heavy object on the copier or subject the copier to shocks. NEVER open any Doors, or turn OFF the copier while the copier is making copies.
4 Safety Notes Chapter 1 2.
5 Chapter 2 1. System Overview p. 6 2. Copier Parts and Accessories Outside the Copier p. 8 Inside the Copier p. 9 Options p. 10 3. Control Panel Keys and Indicators Basic Panel p.12 Display Panel p. 14 4. Turning ON and OFF and Initial Mode p. 15 Turning ON and OFF When the Copier is Turned ON Initial Mode 5. Auxiliary Functions p.
6 1. System Overview ◆Automatic Document Feeder AF-5
7 1. System Overview ◆Duplexing Document Feeder AFR-12
8 2. Copier Parts and Accessories Outside the Copier 6 2 8 9 Chapter 2 3 4 5 1 Getting to Know your Copier 7 10 1139O1010A 12 11 1139O2030A : Slide this Extender out when making copies on large-size paper. 2 Copy Tray Extender Copy Tray 3 Front Door : Open for the following purposes: • Replacing the Toner Bottle.➭ p. 63 • Clearing a paper misfeed.➭ p. 68 • Cleaning the Corona Units. ➭ p. 95 4 1st Drawer 5 2nd Drawer : Holds up to 250 sheets of paper.➭ p.
9 2. Copier Parts and Accessories Inside the Copier 3 6 1 7 1139O2040A 8 5 1139O1030A 3 Lock Release Lever : Turn clockwise to swing up the Upper Half of the copier to clear a paper misfeed. Toner Bottle : Swing open to replace the Toner Bottle. ➭ p. 63 Holder Original Pad : Holds the original in position on the Original Glass. 4 Original Glass 5 Corona Unit : Operate the Lever to clean the corresponding Corona Unit if unwanted Cleaning Lever lines are produced on the copy. ➭ p.
10 2. Copier Parts and Accessories Options 1 2 3 9 8 Chapter 2 4 Getting to Know your Copier 5 7 1151O012AB 6 Automatic Document Feeder AF-5 / Duplexing Document Feeder AFR-12 1 2 3 4 5 Document Exit Tray Document Feed Tray Extender Document Feed Tray Document Guide Plate Document Turnover / Exit Unit Door Lock Release Key : Receives originals that are automatically ejected from the Automatic / Duplexing Document Feeder. : Pull out when loading large-size originals.
11 2. Copier Parts and Accessories 1151O009AA 3 5 2 1 1151O103AA 6 1151O010AA Paper Feed Cabinet PF-204 : Holds up to 500 sheets of paper. ➭ p. 61 1 3rd Drawer 2 Paper Descent Key : Press before sliding the Drawer out or after sliding the Drawer into the copier. ➭ pp. 61, 72 4th Drawer : Holds up to 500 sheets of paper. ➭ p. 61 3 Duplex Unit AD-8 / Paper Feed Cabinet PF-4D 4 Misfeed Removal Guide Plate : Open to clearing a paper misfeed. ➭ p.
12 3. Control Panel Keys and Indicators Basic Panel 1 Getting to Know your Copier Chapter 2 Meter Count Auto Size Manual Staple Mixed Orig. Det. 0.5~2.0 Toner Drum Dehumidify Margin Sort 1 Sort & Staple 2 1 2 3 5 6 7 8 1 2 2in1 1 2 Auto Photo 1 2 Book Job Memory Lighter 2 Darker Auto / Photo 20 19 18 17 16 15 Display Panel See the other pages in this manual. ➭ p. 14 Key Pad Use to enter the number of copies to be made and other numeric data.
13 3. Control Panel Keys and Indicators 2 Auto Darker Photo A4 A3 B4 A3 A3 B4 Full Size A4 FLS. B4 A4 A4 Inch A3 A4 A5 Full Size 2 3 4 5 6 7 8 9 0 C S Auto Paper 1151O041DA 1151O041DA 10 9 8 13 Mixed Original Detection Key Press when making copies using the Automatic / Duplexing Document Feeder in which originals of assorted sizes are loaded together. ➭ p. 25 Copy Key 14 Orig Press to select the type of copying job you wish to make. ➭ p.
14 3. Control Panel Keys and Indicators Display Panel 1 3 4 5 6 7 8 0.5~2.0 Chapter 2 Getting to Know your Copier 2 Auto Auto Photo Lighter Darker Auto / Photo A4 A3 B4 2 3 4 5 6 7 8 9 0 C S Auto A3 A3 B4 Full Size A4 FLS. B4 A4 A4 Inch A3 A4 A5 Full Size 1 Paper A 1151O041DA 1151O041DA 10 1 2 3 4 5 Closure Failure Indicator Indicates that a Door is left open or any option is not set correctly. ➭ p.
15 4. Turning ON and OFF and Initial Mode Turning ON and OFF ● Turning Copier ON Press the Power Switch to the I (ON) position. ● Turning Copier OFF Press the Power Switch to the When Copier is Turned ON The Wait Indicator lights up on the control panel and the Start Key turns orange, indicating that the copier is now warming up. Loading the originals onto the Automatic / Duplexing Document Feeder and pressing the Start Key can set the copier into the Auto Copy Start Function.➭ p.
Getting to Know your Copier Chapter 2 16 5. Auxiliary Functions Panel Resetting Auto Shut OFF Function The Panel Reset Key resets all control panel settings to default settings including the number of copies and zoom ratio. * If an Automatic / Duplexing Document Feeder is used, the original present on the Original Glass will be ejected out of the unit. The Auto Shut OFF Function shuts down the copier a given period of time after the copier has been used last. The initial setting is 60 min.
17 5. Auxiliary Functions One copying job program that is frequently used can be stored in memory and called up later as necessary. Job Memory Setting 1 Press the job Memory Input Key. * The Job Memory Indicator Starts blinking. Input Job Memory Useful Tip The time for the copier to enter the Energy Saver Mode can be selected from 1 to 120 min. by using User’s Choice. ➭ p. 56 1139O8032A 2 Make the control panel settings for the job to be stored in job memory. 3 Press the Job Memory Select Key.
Getting to Know your Copier Chapter 2 18
19 Chapter 3 Making Copies ▲ Making Copies 1. Basic Copying Overview p. 20 2. Placing Originals • Placing on the Original Glass p. 22 • Using the Automatic/Duplexing Document Feeder p. 24 • Using the Mixed Original Detection Mode p. 25 • Using the Single Automatic Document Feeding Mode (SADF Mode) p. 26 3. Manual Bypass Copying p. 28 4. Copy Paper Size p. 30 5. Zoom Ratio p. 32 6. Image Density p. 34 • Auto Exposure Mode • Manual Exposure Mode • Photo Mode 7. Original Copy Type p.
20 1. Basic Copying Overview • Place the original in position (step 1), set the number of copies to be made (step 9), and press the Start Key (step 10). This will allow you to make a full-size copy or copies on paper of the same size as the original. *Automatically selected in the initial mode are Auto Paper, full size, and Auto Exposure. • The selections will change the exposure level, zoom ratio, the type of copy and so on. 1.
21 1. Basic Copying Overview To sort copies Staple 6. Press the Finishing Key to select the desired finishing mode. ➭ p. 40 Group Finishing 1151O087CA To make a file margin on the copy 7. Press the File Margin Key to set the copier into the File Margin Mode. ➭ p. 46 Chapter 3 Margin To make a cover copy Making Copies 1139O2552A 8. Press the Cover Key to set the copier into the Cover Mode. ➭ p. 47 Cover 1139O2562CA 9. Setting the number of copies.
22 2. Placing Originals Placing on the Original Glass Sheet Originals Highly Transparent Originals (Using plain paper or thick paper) (Using transparencies and translucent paper for the original) 1 Raise the Original Cover. 1 Place the original in the same way as the sheet originals. 2 Place the original face down on the Original Glass. 2 Place a blank sheet of paper of the same size over the original.
23 2. Placing Originals Instructions for Original Placement Making Copies from A Book Using Book Copy Mode • Be sure to raise the Original Cover 15° ("Book" refers to an open bound original.) 1 Place the open book so that the higher-numbered page faces toward the Original Width Scale. or more before placing the original. If the Original Cover is raised to an angle less than 15°, the copier may fail to select the correct copy paper size or zoom ratio.
24 2. Placing Originals Using the Automatic/Depleting Document Feeder Automatic/Depleting Document Feeder automatically feeds in sheet originals placed on the Document Feed Tray one by one. After the copy cycle has been completed, it automatically ejects the original out onto the Document Exit Tray. Some originals may not be suitable for reliable operation of the Document Feeder. Here is a guideline.
25 2. Placing Originals Slide the Document Guide Plate to the size of the originals. ∗When using large size originals, flip up the Document Feed Tray Extender. Use the Mixed Original Detection mode to make copies automatically from originals of assorted sizes loaded in the Automatic/Duplexing Document Feeder. If Auto Size is selected, you can make copies of the same size from originals of different sizes.
26 2. Placing Originals Using the Single Automatic Document Feeding Mode (SADF Mode) This is the mode in which you load your originals one by one onto the Automatic/Duplexing Document Feeder to make a copy or copies from it. When you load the original, the copier automatically starts the copy cycle. NOTES Making Copies Type : Plain paper Thickness : 35g/m 2 to 200g/m2 . S ize : A3 to A5L • The following features cannot be selected in the SADF Mode.
27 2. Placing Originals Originals Not Suitable for the Automatic/Duplexing Document Feeder Raise the Automatic/Duplexing Document Feeder. 2 Place the original face down on the Original Glass. 1151O020AA 3 Align the rear left corner of the original with the marker on the Original Width Scale. Then press the rear edge of the original up against the Original Positioning Plate at the rear side of the Glass.
28 3. Manual Bypass Copying Use the Manual Bypass to make copies on paper not loaded in any Drawer, or to copy onto transparencies, translucent paper, or any other special paper. When using the Multi Bypass Tray, you can load multiple sheets of copy paper. Making Copies Chapter 3 Copy Paper That Can be Used for Manual Bypass ◆Types of Paper 2 2 • Plain paper (weighing 60g/m to 90g/m ) 2 2 • Thick paper (weighing 90g/m to 157g/m ) • Transparencies, translucent paper ◆Paper Size • Max.
29 3. Manual Bypass Copying 4 Ensure that the the Control Panel. Indicator is lit on IMPORTANT When making multiple copies using OHP transparencies, set the Copy Tray into the upper position if there is no Sorter or Staple Sorter mounted. 1139O3690A 1139O3690A Using the Key Pad, set the number of copies to be made. 1 2 3 4 5 6 7 8 9 0 C Making Copies 5 1139O2640A 6 Chapter 3 * If not, insert the paper stack on the Tray again. Press the Start Key to start the copy cycle.
30 4. Copy Paper Size The selected copy paper size and the paper source loaded with that paper are indicated on the control panel. 0.5~2.0 Auto Auto Photo Lighter Darker Auto / Photo 2 3 4 5 6 7 8 9 0 C S Auto A4 A3 B4 A3 A3 B4 Full Size A4 FLS.
31 4. Copy Paper Size Useful Tip A Drawer, if set as a special paper drawer, is excluded from paper sources that can be selected in the Auto Paper Mode. The Special Paper Indicator S and Paper Size Indicator light up when you select a particular Drawer for which the special paper setting was made. This feature is a great advantage when you need to make a large number of copies on the same size paper.
32 5. Zoom Raito You can select the desired fixed zoom ratio by pressing the keys. There are three different ways to choose from to set the zoom ratio. Select one according to your need. 0.5~2.0 Auto Auto Photo Lighter Darker Auto / Photo A4 A3 B4 2 3 4 5 6 7 8 9 0 C S Auto A3 A3 B4 Full Size A4 FLS.
33 5. Zoom Raito Using Zoom Up/Down Keys Pressing the or key changes the zoom ratio shown in 0.001 increments. You can keep touching the key to change the ratio quickly. Hold down the or key until the desired zoom raito is reached Chapter 3 0.5~2.0 1151O050AA 1151O050AA Useful Tip To save time, first select the fixed zoom ratio nearest to the target ratio or Key.
34 6. Image Density Pressing the Exposure Control Keys < A > can adjust the image density level of copie s either in the Auto Exposure Mode, Manual Exposure Mode, or Photo Mode. Select the appropriate mode according to your particular needs. 0.5~2.0 Auto Auto Photo Lighter Darker Auto / Photo A4 A3 B4 2 3 4 5 6 7 8 9 0 C S Auto A3 A3 B4 Full Size A4 FLS.
35 6. Image Density Photo Mode The copier can make a faithful reproduction of an original having halftone image such as photos. The image density of the photo may be varied in nine steps.
▲ 36 7. Original Copy Type ▲ Pressing the Orig. Copy Keys can select the setting for the type of copy you want to make from the type of original you have. There are eight different modes available. Select one according to your need. Auto Size Meter Count Manual Staple Mixed Orig. Det. 0.5~2.0 Margin Toner Drum Dehumidify Sort 1 2 Sort & Staple 2 1 1 2 2in1 Book 2 Book 2 Lighter Darker Auto / Photo Finishing Orig. Copy Auto A4 A3 B4 A3 A3 B4 Full Size A4 FLS.
37 ▲ 2-sided ▲ 7. Original Copy Type 2-sided Original • Select this mode to make 2-sided copies from 2-sided originals. (Only when the Duplexing Document Feeder and Duplex Unit are mounted.) Copy 1139O0300A 1-sided [2 in 1] • Select Copy 1140O273 this mode to make a 1-sided copy, through reduction, from two 1-sided originals side-by-side. (Only when the Automatic/Duplexing Document Feeder is mounted.) * You need half as many sheets of copy paper as required otherwise.
38 Copy Type ▲ 7. Original ▲ Selecting Original Copy Type Each time the Original Copy Key (right) is pressed, the newly selected type indicator lights as shown below. ▲ ▲▲ 1 Press the Original Copy key to select the Original Copy type. 2 2 1 1 1 2in1 Book 1 Book 2 2 1 2 2in1 Orig. Copy Making Copies Each time the Original Copy Key (left) is pressed, the newly selected original type indicator lights as shown below.
39 ▲ 7. Original Copy Type Instructions for Loading Originals Use the following procedure for loading originals to make 1-sided copies from 2-sided originals. Procedure Load the originals crosswise. If the originals are loaded lengthwise, the directions of the copy images will be mixed up.
40 8. Finishing Mode Pressing the Finishing Key can select the desired finishing mode. There are five different finishing modes. Select the one according to your needs. Meter Count Manual Staple Auto Size Mixed Orig. Det. 0.5~2.0 Margin Toner Drum Dehumidify Sort 1 2 Sort & Staple 2 1 1 2 2in1 Auto Photo Cover 1 Book Group 2 2 Lighter 2 Book Job Memory Chapter 3 Input 1 1 2in1 Darker Auto / Photo Finishing Orig. A4 A3 B4 Auto A3 A3 B4 Full Size A4 FLS.
41 8. Finishing Mode Group Copies 1st Bin Originals 2nd Bin The copies made from each single original are separated into groups. Each group contains the same number of copies. (Only when the Sorter or Staple Sorter is mounted) 3rd Bin 1076O147 Manual Staple This mode allows you to staple copy sets already made in the Sort Mode or copy stacks made in the Group Mode. (Only when the Staple Sorter is mounted.) * This feature is efficient for stapling originals after making copies.
42 8. Finishing Mode Selecting the Finishing Mode Sort/Sort-and-Staple/Group Mode Using the Manual Staple Mode (To sort or group copies) (To staple copy sets already made in the Sort Mode or copy stacks made in the Group Mode.) 1 Press the Finishing Key to select the desired mode. 1 Make sure that each copy set or stack has been fed into the Sorter Bin. 2 Press the Manual Staple Key. Then the copy set or stack in the Sorter Bin will be stapled.
43 8. Finishing Mode Using the Manual Staple Mode (To use as a stapler) 1 Align the sheets of paper neatly. 3 Press the Manual Staple Key. The paper stack will be stapled. Manual Staple Insert the paper stack onto the 1st Bin with its front surface facing up. 1139O2732A Useful Tip This feature is efficient for stapling originals after making copies. 1139O1320A Stapling Position 1151O110AA NOTES sure of the stapling position and press the paper stack against the bracket.
44 8. Finishing Mode Instructions for Loading Originals for Finishing Mode Note the correct direction of the originals if the copies are to be stapled either in the Sort-and-Staple or Manual Staple mode. Using the Automatic/Duplexing Document Feeder Load the originals crosswise in the Document Feeder. Ensure also that the stapling position is at the rear left corner as indicated by the arrow.
45 8. Finishing Mode Auto Dual Function Each of the Sort Bins holds up to 25 sheets of paper. The Auto Dual Function, however, allows sorting of copies of up to 50 originals under certain conditions. Auto Dual Function in the Sort Mode When 5 or less copies are made from an original set consisting of more than 25 originals in the Sort Mode, the Sorter or Staple Sorter is automatically switched into the Auto Dual Function Mode using the 6th to 10th Bins.
46 9. File Margin Mode ▲ The copier provides a file margin (10mm) along the leading edge of the copy for your easy filing. Both 1-sided and 2-sided originals can be used in the File Margin Mode. Select the appropriate Original Copy type according to the originals.
47 10. Cover Mode The Cover Mode lets you make a front cover for a copy set by copying the first page of an original set on a different type of paper, such as color paper. It may be used to differentiate the cover of a copy set from other pages. Original Set Copy Set Special paper, such as colored one NOTES • This mode can only be selected when the copier is equipped with the Automatic/Duplexing Document Feeder and the Multi Bypass Tray. 2-sided Mode is Selected.
Making Copies Chapter 3 48
49 Chapter 4 Special Functions This chapter explains about the special functions that can be used for specific purposes. Special Functions Chapter 4 1. Meter Count p. 50 2. Toner Replenisher/Drum Dehumidifier p. 51 3. User’s Choice Description of Each User’s Choice Functions p. 52 Making the User’s Choice Settings p.
50 1. Meter Count This function allows you to check the total count of each of the four different counters. Total 2-Sided Total Shows the number of 2-sided copies made. Shows the total number of copies made since the installation of the copier. Size 2-Sided Size Shows the number of copies made on the copy paper of a preset size. (The size will be set by your Technical Representative.) Shows the number of 2-sided copies made on the copy paper of a preset size (the same size as set for "Size").
51 2. Toner Replenisher/Drum Dehumidifier Toner Replenisher The copier tends to exhaust the supply of toner rapidly when making a number of copies from an original with dark solid areas such as a photo. As a result, the image density of the copy will become lighter. In such a case, you can use the Toner Replenisher function to regain the normal image density quickly. Press the Auxiliary Toner Replenishing Key. *This causes the copier to initiate toner replenishing, which lasts for 90 seconds at maximum.
52 3. User’s Choice The copier has been set so that the most frequently used setting are automatically selected in the initial mode. The User’s Choice allows you to select the default setting which are automatically selected in the initial mode according to your own needs.
53 3. User’s Choice U-9 File Margin Select whether the original has file margin or not for the File Margin mode. If "1" (original does not have a file margin") is set and you attempt to make a copy from an original which has a file margin on it, the copier is very likely to produce a copy with a margin on an incorrect position.
54 3. User’s Choice U-12 AP/AS/Manual Priority Select the priority copying mode that is automatically selected when the Power Switch is turned ON or Panel Reset key is pressed Setting Value Initial Setting Description Auto Paper (AP) Auto Size (AS) Manual 0 1 2 1151H13BA U-13 Default Auto Exposure Level Determine the optimum exposure level in the Auto Exposure mode, variable in seven steps.
55 3.
56 3. User’s Choice U-20 Auto Panel Reset ON/OFF Select whether or not to activate the auto clear function after the lapse of a given period of time a after copy cycle has been completed or a key on the control panel has been operated. Setting Value 0 Disabled 1 Enabled : 30 sec. 2 Enabled : 1 min.
57 3. User’s Choice U-24 Sort/Non-Sort Auto Switching ON/OFF Select whether to enable or disable the function that automatically switches between the Sort and Non-Sort mode depending on the number of originals loaded in the ADF when the copier is equipped with an ADF and finishing option. If "ON" is selected, Non-Sort is selected if only one original is loaded in the ADF and Sort is selected if two or more originals are loaded in the ADF.
58 3. User’s Choice Making the User’s Choice Mode Settings 1 Keep pressing the Panel Reset Key for about 3 seconds. * U is shown on the Zoom Ratio Indicator. 4 Press the Clear Key. *This clears the current setting (shown on the Multi-Copy Display) of that particular choice code. Panel Reset 1 2 3 4 5 6 7 8 9 0 C 1139O4782A 1139O4782A Zoom Ratio Indicator Multi-Copy Display Chapter 4 Using the Key Pad, enter the desired Choice Code number.
59 Chapter 5 When an Indicator Lights Up (Replenishing Supplies, Clearing Misfeeds, and Correcting a Closure Failure) This chapter explains about the details of the various warning indications given on the control panel, including those that entail inhibition of the initiation of a copy cycle. It also shows action to be taken for each case. When an Indicator Lights Up When the Add Paper Indicator Lights Up p. 60 When the Add Toner Indicator Lights Up p. 63 When the Add Staple Indicator Lights Up p.
60 1. When the Add Paper Indicator Lights Up When the Drawer currently selected for use has run out of paper, the Add Paper Indicator lights up. At this time, you cannot start any new copy cycle. Fan the paper thoroughly. Auto Auto Photo Lighter Darker Auto / Photo A3 B4 A4 FLS. A4 Inch A5 Paper A front side 1139O1370A 1151O071DA 1151O071DA Example: 1st Drawer has run out of paper. Use the following procedure to load paper into the Drawer.
61 1. 2nd Drawer 1 When the Add Paper Indicator Lights Up 3rd/4th Drawer (PF-204) Slide out the 2nd Drawer and press down the Paper Lifting Plate until it is locked into position. 1 Slide the drawer out of the copier. 1139O0460A 2 Load the paper stack into the Drawer so that its front side faces down. Make sure that the paper stack rests under the two catches of the Drawer. 2 Load the paper stack into the Drawer so that its front side faces down.
62 1. When the Add Paper Indicator Lights Up 3rd Drawer (PF-104) 1 Press the Paper Descent Key. This releases the 3rd Drawer, allowing you to slide it out of the copier. 3 Load another paper stack in the left-hand half of the Drawer, front side face down. At this time, press the trailing edge of the paper stack tightly up against the left edge of the Drawer.
63 2. When the Add Toner Indicator Lights Up The Add Toner Indicator lights up when toner in the Toner Bottle is running out. 0.5~2.0 Auto Auto Photo Darker uto / Photo Auto A4 A3 B4 A3 A3 B4 Full Size A4 FLS. B4 A4 A4 Inch A3 A4 A5 Full Size Paper A You can still make copies, but the image density will become lighter and lighter. It is recommended, therefore, that you replace the Toner Bottle with a new one as soon as possible.
64 3. When the Add Staple Indicator Lights Up When the staples will soon run out, the Add Staple Indicator lights up. 0.5~2.0 Auto Auto Photo Darker / Photo A4 A3 B4 Auto A3 A3 B4 Full Size A4 FLS. B4 A4 A4 Inch A3 A4 A5 Full Size Replace the Staple Cartridge with a new one by following the procedure given below. Paper A 1151O073DA 1151O073DA Replacing the Staple Cartridge 1 Press the Lock Release Lever of the Staple Sorter and slide it away from the copier.
65 3. Place a sheet of paper into the 1st Bin of the Staple Sorter. 1139O1320A the Add Staple Indicator lights up. Removing the Staple Cartridge before then will result in stapling trouble. • Immediately after the new Staple Cartridge has been loaded, be sure to follow steps 7 to 9. • Do not turn the green gear near the Cartridge inside the Stapler Unit. Press the Manual Staple Key. * The copier automatically test-staples the paper 2 to 3 times.
66 4. When the Closure Failure Indicator Lights Up Full Size A4 The Closure Failure Indicator lights up if a copier door or cover is left open, or an option is not attached properly. At this time, the Monitor Display shows the location of the closure failure. You can no longer start a new B4 copy cycle. FL B4 A4 A4 Inc A3 A4 A5 0.5~2.0 Auto Photo Lighter Darker Auto / Photo Auto A4 A3 B4 A3 A3 Full Size A Paper Correct the closure failure by following the procedure given below.
67 4. Monitor Display When the Closure Failure Indicator Lights Up Check Location Check that the Left Door is closed. 1139O4010A Check that the Lower Right Door is closed. 1139O4020A Check that the Duplex Unit is locked into position. 1139O4040A Check that the Sorter or Staple Sorter is in position. 1139O4050A When an Indicator Lights Up 1139O4030A Chapter 5 Check that the Lower Left Door is closed.
68 5. When the Misfeed Indicator Lights Up 0.5~2.0 Auto Photo Lighter Darker Auto / Photo Auto If a paper misfeed occurs during a copy cycle, that copy cycle stops. At this time, the Misfeed Indicator lights up, the Monitor Display shows the location and you cannot start any new copy cycle.
69 5. When the Misfeed Indicator Lights Up Misfeed Clearing Procedures Copier (Fusing/Transport Section) NOTE Be careful not to touch the areas marked with High Voltage and Caution: HOT with bare hands. 1151O113AA 2 Holding up the Fusing Unit, pull out the sheet of paper in the direction of the arrow. 3 Remove any sheet of paper from the Transport Section. 4 Slightly lift up the Upper Half of the copier and unlock Stopper M2 . Gently swing down and lock the Upper Half of the copier.
70 5. When the Misfeed Indicator Lights Up Copier (Paper Take-Up Section) 1 4 Open the Front Door. Turn the Lock Release Lever counterclockwise to unlock and swing up the Upper Half of the copier.Then lock Stopper M2 . Slightly lift up the Upper Half of the copier and unlock Stopper M2 . Gently swing down and lock the Upper Half of the copier. Then, close the Front Door.
71 5. When the Misfeed Indicator Lights Up Copier (Multi Bypass Section) 1 Unload the stack of paper from the Multi Bypass Tray. 4 Slightly lift up the Upper Half of the copier and unlock Stopper M2 . Gently swing down and lock the Upper Half of the copier. Then, close the Front Door. 1139O2160A 1151O114AB 5 Fan the paper thoroughly. Reload the paper stack onto the Multi Bypass Tray. 1151O113AA 1139O2090A 3 Remove any sheet of paper from the Transport Section.
72 5. When the Misfeed Indicator Lights Up Paper Feed Cabinet (PF-104) When an Indicator Lights Up Chapter 5 Paper Feed Cabinet (PF-204) 1 Open the Lower Right Door and pull out the sheet of paper. 1 Open the Lower Right Door and pull out the sheet of paper. 2 Close the Lower Right Door. 2 Close the Lower Right Door. 3 Slide the Drawer out of the copier. 3 Press the Paper Descent Key. This releases the Drawer, allowing you to slide it out of the copier.
73 5. When the Misfeed Indicator Lights Up Duplex Unit 1 Open the Front Door. Turn the Lock Release Lever counterclockwise to unlock and swing up the Upper Half of the copier. Then lock Stopper M2 . 5 Close the Lower Right Door. 6 Slightly lift up the Upper Half of the copier and unlock Stopper M2 . Gently swing down and lock the Upper Half of the copier. Then, close the Front Door. 7 Slide out the Duplex Unit and open Misfeed Removal Guide Plate D .
74 5. When the Misfeed Indicator Lights Up Duplexing Document Feeder 1 Remove the original stack from the Document Feed Tray. 5 Raise the Duplexing Document Feeder. Opening the Document Turnover/Feed Unit Guide Plate, gently pull out the original from the Unit. 1151O097AA 2 Swing open Document Feed Unit Door F1 and gently pull out the original. 1151O033AA 6 Remove the original from the Original Glass and lower the Duplexing Document Feeder.
75 5. When the Misfeed Indicator Lights Up Automatic Document Feeder 1 Remove the original stack from the Document Feed Tray. 6 Remove the original from the Original Glass and lower the Automatic Document Feeder. 7 Return the number of originals indicated on the Display at the back of the original stack removed in step 1 and reload it onto the Document Feed Tray. Example : Return two originals. 1151O097AA 2 Swing open Document Feed Unit Door F1 , and gently pull out the original. Close F1 .
76 5. When the Misfeed Indicator Lights Up When an Indicator Lights Up Chapter 5 Sorter/Staple Sorter 1 Holding the Lock Release Lever, slide the Sorter/Staple Sorter away from the copier. 2 Pull out the copy from the Transport Section. 3 Slide the Sorter/Staple Sorter back to the copier.
77 6. When the Call-Tech.-Rep. Indicator Lights Up 0.5~2.0 Auto Photo Lighter Darker Auto / Photo Auto A4 A3 B4 A3 A3 Full Size A4 B4 A4 A4 A3 A4 A5 Full Size A Paper When a malfunction occurs in the copier, the Call-Tech.-Rep. Indicator lights up and the corresponding malfunction code appears across the Zoom Ratio Indicator and Multi-Copy Display. At this time, the Start Key turns to orange and you cannot start a new copy cycle. Try to clear the Call-Tech.-Rep.
78 7. When the I. U. Service Life Indicator Light Up When time is about to come when the Imaging Unit needs replacement, the I. U. Service Life Indicator starts blinking to prompt you to replace it with a new one. Replace the Imaging Unit by following the procedure given below. 0.5~2.0 Auto Auto A4 A3 B4 A3 A3 B4 Full Size A4 FLS. B4 A4 A4 Inch A4 A5 A3 1151O100DA 1151O100DA When 2,500 more copies are made with Add Toner Indicator lighting up, or 7,500 more copies are made, after the I.
79 7. Remove the I. U. from copier 1 When the I. U. Service Life Indicator Lights Up Unpacking / Setting up the I. U. Open the Front Door. Turn the Lock Release Lever counterclockwise to unlock and swing up the Upper Half ofthe copier. Then lock Stopper M2 . 1 Peel off the piece of tape and open the Carton Box. Take the Starter Bottle out from the Carton Box. Take the I. U. with its bag out of the Carton Box. Starter Bottle 1151O113AA 2 Turn the I. U.
80 7. When the I. U. Service Life Indicator Lights Up 4 Carefully pull the polyester tape from the I. U.. 8 Be sure to push the I. U. into the locked position until a click is heard. Then, check to see the position of Lock Release Lever, as shown in the illustration. 4445U011AA 5 Remove the Cap from the I. U. and re-fit it to the used I. U. as shown in the illustration. 4445U005AA NOTE An improperly installed I. U. could be a cause of copier malfunction.
81 7. When the I. U. Service Life Indicator Light Up Charging the Copier with Starter and Toner 1 Swing out the Bottle Holder. 4 Align the markings on the Starter Bottle with the upper side of the Bottle Holder and slide the Bottle into position. 4445U006AA 2 Hold the Starter Bottle so that its tab is on the upper side, shake it well. 4445U008AA NOTE 3 5 Then, swing in the Bottle Holder until it locks into position. Close the Front Door.
82 7. 7 When the I. U. Service Life Indicator Lights Up The copier automatically start the charging cycle for approximately 5 minutes. 8 During this cycles, do not open the Front Door. During this cycle, six segments of the ones digit LED on the Magnification Ratio Indicator forming a "0" light up and go out one after another, indicating that the copier is being charged with starter.
83 7. 11 When the I. U. Service Life Indicator Lights Up Align the markings on the Toner Bottle with the upper side of the Bottle Holder and slide the Bottle into position. 1139O1420A NOTE Insert the Bottle all the way into the copier until the marking on the Bottle is aligned with the marking on the Bottle Holder. Chapter 5 Then, swing in the Bottle Holder until it locks into position and close the Front Door.
84 8. Quick Reference for Other Indicators Indicator Copier State Action Wait until the Wait Indicator goes The copier is warming up. out and the Start Key turns green. A copy cycle cannot be initiated while the Wait Indicator remains lit. Wait Indicator 1139O3260A Remove Copies Indicator There is a copy or copies left in the Remove the copy or copies from Sorter Bin(s). the Sorter Bin(s). 1139O3400A Paper Size Display S Auto A3 B4 A4 B5 A4 FLS.
85 Chapter 6 Troubleshooting This chapter gives you instructions on how to troubleshoot copier malfunctions. Troubleshooting Chapter 6 1. When this Type of Copy is Produced p. 86 • The image is too light • The image is too dark • The copy is blurry • The copy has dark specks or spots • The edge of the copy is dirty • The image on the copy is not aligned properly • The copy has lines 2. The Copier is not functioning as designed p.
86 1. When This Type of Copy is Produced Symptom Possible Cause The image is too light. Change the setting of the User’s Choice (Exposure Priority). ➭ p. 54 Cancel the Auto Exposure Mode and select the Manual Exposure Mode to adjust the exposure level to obtain a darker image. ➭ p . 34 The manual exposure level is set Press the Exposure Control Key as on the lighter side. necessary to obtain a darker image. ➭ p. 34 You have been making copies from The copier needs more toner.
87 1. When This Type of Copy is Produced Symptom Possible Cause The copy has dark specks or spots. The Original Glass is dirty. Action Wipe the Original Glass clean with a soft dry cloth. ➭ p. 94 The edge of the copy is dirty. 1074O112 The image on the copy is not aligned properly. The original is not placed in the correct position. The originals may not be suitable for use in the Document Feeder. Place the original correctly on the Original Glass. ➭ p.
88 2. The Copier is not functioning as designed Symptom The Control Panel shows nothing. Check for: Is only the Start Key lit up green? Action The copier is in the Energy Saver Mode. Press any key on the Control Panel to cancel the Energy Saver Mode. ➭ p. 17 The copier is in the Auto Shut OFF Turn the Power Switch ON. Mode. ➭ p. 16 No copies are fed out when the Start Key is pressed. The Wait Indicator is lit up. The copier was just turned ON and is warming up. Please wait.
89 Chapter 7 Miscellaneous This chapter gives complete specifications of the copier system and options, plus care and reference information to facilitate your use of the copier. Miscellaneous Chapter 7 1. Specifications p. 90 • Copier • Duplexing Document Feeder • Automatic Document Feeder • Sorter • Staple Sorter • Paper Feed Cabinet • Duplex Unit 2. Care of the Copier p. 94 • Cleaning 3. Function Combination Matrix p. 96 4. Description of Copy Paper Size and Zoom Ratio Table p. 98 5. Index p.
90 1. Specifications Copier EP2010 Type Platen Type Photoconductor Copying System Developing System Fusing System Types of Original Kinds of Paper Copy Paper Size Paper Feeding System Warm-up Time First Copy Miscellaneous Chapter 7 Copy Speed (Approx.
91 1. Specifications Duplexing Document Feeder AFR-12 Document Feeding System Standard Mode : 1-sided original, 2-sided original, 2-in-1, Single Feeding Mixed Original Detection Mode: 1-sided Mixed Original Detection 2-sided Mixed Original Detection Lightweight Original Mode Kinds of Original Original Weight Plain paper 1-sided original Mode, 2-in-1 Mode 2-sided original Mode : 50g/m2 to 110g/m 2 : 60g/m2 to 90g/m2. Single Feeding Mode : 35g/m2 to 200g/m 2.
92 1. Specifications Sorter S-106 No.
93 1. Specifications Paper Feed Cabinet PF-204 Kinds of Paper Copy Paper Size Paper Feeding System Power Source Dimensions Weight Plain paper, Recycled paper : Weighing 60g/m 2 to 90g/m 2 3rd Drawer : A5L to A3L 4th Drawer : 210mm×280mmL to A3L Automatic feeding from drawer Total Drawer Capacity : 1,000 sheets (500sheets ✕ 2) DC24V supplied from copier Width : 610mm Depth : 595mm Height : 35.
94 2. Care of the Copier Cleaning (Turn OFF the Power Switch of the copier when cleaning.) Original Glass Housing Wipe the surface of the Housing clean with a soft cloth dampened with mild home detergent. Wipe the surface of the Original Glass clean with a soft, dry cloth. 1139O1820A Control Panel Front Door Wipe the surface of the Control Panel clean with a soft, dry cloth.
95 2. Care of the Copier Corona Units 1 Document Transport Belt Gently slide out the Corona Unit Cleaning Lever (Upper) as far as it goes. 1 1139O1910A 1139O1870A 2 Gently slide the Cleaning Lever back into the original position. 2 Gently slide out the Corona Unit Cleaning Lever (Lower) as far as it goes. Hold the Document Transport Belt at both edges and pull it to the left to expose a fresh surface.
● 1 FinishNon-Sort ing Manual Exposure ● ● O O O O O O O O O O O O O O O O O O O O O O O ● ● O O O O O O O O O O O O O O O O O O O O O O O ● ● O O O O O O O O O O O O O O O O O O O O ● ●l O O O O O O O O O O O X O O O O ● Auto Size Zoom Ratio Full Size(100%) Reduc., Enlg.
97 3. Function Combination Matrix Combinations for Combined Functions •1 2 2[2 in1] • Book • Book ▼ ▼ •1 ▼ ▼ ▼ A to F : The settings can be made only when the copier is equipped with the following options. A : Duplex Unit B : Duplexing Document Feeder C : Automatic Document Feeder D : 10-Bin Sorter E : Staple Sorter G : The Cover mode cannot be selected when any of the following settings has been made for Org. Copy.
98 4.
99 ▼ ▼▼ ▼▼ ▼ 5. Index 1-sided 1-sided P.36 1-sided 1-sided(2in1) P.37 1-sided 2-sided P.36 1-sided 2-sided(2in1) P.37 2-sided 1-sided P.36 2-sided 2-sided P.37 2-sided Size Counter P.50 2-sided Total Counter P.50 A Basic Panel P.12 Book 1-sided P.37 Book 2-sided P.37 D Call-Tech.-Rep.Indicator P.77 Care of the Copier P.94 Cleaning P.94 Clear Key P.12 Closure Failure Indicator P.66 Control Panel P.12 Copy Paper Size P.30 Corona Unit Cleaning Lever P.9 Cover Mode P.47 Default Auto Exposure Level P.
100 5. Index E F G I Group Mode P.41 Image Density P.34 Initial Mode P.15 Interrupt Mode P.16 I. U. Service Life Indicator P.78 Job Memory P.17 L Lightweight Original P. 52 Manual Bypass Copying P.28 Manual Exposure Mode P.34 Manual Staple Mode P.41 Meter Count P.50 Misfeed Clearing Procedures P.69 Misfeedf Indicator PP.14,68 Mixed Original Detection Mode P.25 Mixed Original Detection P.52 N Non-Sort Mode P.40 O Original Copy Type P.36 Panel Reset Key P.16 Panel Resetting P.
101 5. Index Toner Replenisher Function P.51 Total Counter P.50 Turning ON and OFF P.15 U User’s Choice P.52 W Wait Indicator PP.14,15,84 Z Zoom Ratio P.33 Zoom Ratio Table P.98 Miscellaneous T Single Automatic Document Feeding Mode P.26 Size Counter P.50 Sort Mode P.40 Sort/Non-Sort Auto Switching ON/OFF P.57 Sort-and-Staple Mode P.40 Special Paper Setting P.31 Special Paper Setting P.57 Start Key P.12 Stop Key P.12 System Overview P.
