i EP1083 Thank you for choosing Minolta. This operator’s manual explains how to operate the copier and replenish its supplies. It also gives some troubleshooting tips as well as general precautions to be observed when operating the copier. To ensure the best performance and effective use of your copier, read this manual carefully until you familiarize yourself thoroughly with its operation and features. After you have read through the manual, keep it for ready reference.
ii Contents Chapters 1 through 3 give the basic information for making copies. Be sure to read these chapters before using your copier. Using this Manual Organization viii Page Organization ix Terms and Symbols for the Type of Originals and Copy Paper x Chapter 1 Safety Notes 1. Installing the Copier p. 2 Installation Site Power Source Grounding Space Requirements 2. Precautions for Use p. 4 Operating Environment Using the Copier Properly Care of Copier Supplies Moving p.
iii Contents Chapter 2 Getting to Know your Copier 1. System Overview p. 8 2. Copier Parts and Accessories Outside Copier p. 9 Inside Copier p. 10 Automatic Document Feeder AF-5 p. 12 10-Bin Sorter S-106 p. 13 Multi Bypass Tray MB-4 p. 13 3. Control Panel Keys and Indicators Control Panel p. 14 Display p. 16 4. Turning ON and OFF, and Resetting the Copier Turning ON and OFF p. 19 When Copier is Turned ON p. 19 Auto Copy Start Function p. 20 Minimizing the Warm-up Time p.
iv Contents Chapter 3 Making Copies p. 25 1. Copying Overview p. 26 2. Copying Procedure Placing Originals p. 28 Using the Automatic Document Feeder AF-5 p. 30 Checking the Copy Paper Size and Selecting the Paper Source p. 33 Zoom Ratio • Types of Zoom Ratios p. 34 • Auto Size Mode p. 37 • Zoom Ratio Table (Original Size to Copy Paper Size) p. 39 Image Density p. 40 Book Copying p. 42 Finishing Modes • Finishing Modes p. 44 • Selecting the Finishing Mode p. 45 • Auto Dual Function p.
v Contents Chapter 4 Auxiliary Functions p. 51 1. Checking the Total Number of Copies Mode p. 52 2. Toner Replenisher Function (Increasing the Image Density) p. 54 3. Drum Dehumidifier Function p. 55 4. User’s Choice p. 56 Chapter 5 When an Indicator Lights Up p. 67 (Replenishing Supplies, Clearing Misfeeds, and Correcting a Closure Failure) 1. Quick Reference for Indicator Lights p. 68 2. Detailed Instructions for Indicator Lights Add Toner Indicator p. 70 Add Paper Indicator p.
vi Contents Chapter 6 Troubleshooting p. 93 1. When this Type of Copy is Produced p. 94 The image is too light The image is too dark The copy is blurry The copy has lines The copy has dark specks or spots The edge of the copy is dirty The image on the copy is not aligned properly 2. The Copier is not functioning as designed p.
vii Contents Chapter 8 Miscellaneous p. 107 1. Care of the Copier Chapter 1 Safety Notes Daily Checks P. 108 Cleaning p. 110 2. Description of Copy Paper Size p. 114 3. Zoom Ratio Table (Original Size to Copy Paper Size) p. 115 4. Index p.
viii Using This Manual Organization Chapters 1 through 3 give the basic information for making copies. Be sure to read these Chapters before using your copier. Chapter 1 Safety Notes About the operating environment, conditions and precautions for use. Chapter 2 First Things to Know your Copier A brief description of the system and preliminary information about the different parts of the system. Chapter 3 Making Copies About how to make copies. "COPYING OVERVIEW" on p.
ix Using This Manual Page Organization Each page of this manual is basically organized as follows. Index: To locate your Chapter quickly. Section title 1142O166CA Table of contents of the Chapter: To quickly locate your page in the chapter. ➭ p. XX (Cross-reference): Shows the page to refer to for more detailed information. Control Panel Indicators A steady light and blinking light Indicator on the control panel are indicated as follows.
x Using This Manual Terms and Symbols for the Type of Originals and Copy Paper A few special terms and symbols are used in this manual to designate types of originals and copy paper. These two pages explain about these terms and symbols. Feeding Direction (Copy Paper Path) In this copier system, copy paper is taken up from the right-hand side of the copier and fed through the copier toward the left-hand side, out face up onto the Exit Tray.
xi Using This Manual "Width" and "Length" When we talk about the size of the original or copy, we call side A "width" and side B "length." A: Width B: Length 1139O1610A Terms and Symbols Used When the original or copy has a "length" longer than its "width," we call it "lengthwise" and use symbol "L" or " ." 1139O1610A When the original or copy has a "length" shorter than its "width," we call it "crosswise" and use symbol "C" or " .
xii
Chapter 1 Safety Notes Safety Notes Chapter 1 1 This Chapter explains about the operating environment, conditions, and precautions for use. 1. Installing the Copier p. 2 Installation Site Power Source Grounding Space Requirements 2. Precautions for Use p.
2 Safety Notes Chapter 1 1. Installing the Copier Installation Site To ensure utmost safety and prevent possible malfunctions of the copier, install it in a location which meets the following requirements. u A place away from a curtain or the like that may catch fire and burn easily. u An area where there is no possibility of being splashed with water or other types of liquid. u An area free from direct sunlight. u A place out of the direct air stream of an air conditioner, heater, or ventilator.
3 Space Requirements • EP1083 Safety Notes To ensure easy copier operation, supply replacement and service maintenance, adhere to the recommended space requirements detailed below. NOTE: Be sure to allow a clearance of 150mm. or more at the back of the copier as there is a ventilation duct. 1,063 633 430 469 1,250 655 372 841 253 387 1152O037AA 1152O038AA + OPTION 1,138 1,632 467 671 979 1,359 497 • EP1083 1152O039AA Chapter 1 1.
4 Safety Notes Chapter 1 2. Precautions for Use Operating Environment The operating environmental requirements of the copier are as follows. Temperature Humidity : 10°C to 30°C (50°F to 86°F) with a fluctuation of 10°C (50°F) per hour : 15% to 85% with a fluctuation of 20% per hour Using the Copier Properly To ensure the optimum performance of the copier, follow the precautions listed below. u NEVER place a heavy object on the copier or subject the copier to shocks.
5 = Placer le copieur dans une pièce largement ventilée = Une quantité d’ozone négligable est dégagée pendant le fonctionnement du copieur quand celui-ci est utilisé normalement. Cependant, une odeur désagréable peut être ressentie dans les pièces dont l’aération est insuffisante et lorsque une utilisation prolongée du copieur est effectuée.
6 Safety Notes Chapter 1 2.
7 This Chapter gives you a brief description of the system and preliminary information about the different parts of the system. 1. System Overview p. 8 2. Copier Parts and Accessories Outside Copier p. 9 Inside Copier p. 10 Automatic Document Feeder AF-5 p. 12 10-Bin Sorter S-106 p.13 Multi Bypass Tray MB-4 p. 13 3. Control Panel Keys and Indicators Control Panel p. 14 Display p. 16 4. Turning ON and OFF, and Resetting the Copier Turning ON and OFF p. 19 When Copier is Turned ON p.
8 1. System Overview The EP1083 system can be configured with the following components. Getting to Know your Copier Chapter 2 ◆ Automatic Document Feeder AF-5
9 2. Copier Parts and Accessories Outside Copier 3 4 5 10 9 8 7 6 1142O011AA 1 Control Panel 2 Original Cover 3 Power Switch : Use to start a copy cycle or to make copying-job settings. ➭ p. 14 : Holds the original placed on the Original Glass in position. To place an original, raise the Cover and place it in position on the Original Glass. ➭ p. 28 : Use to turn the copier ON and OFF. ➭ p. 19 4 Manual Bypass Tray : Use for manual feeding of paper into the copier. ➭ p.
10 2. Copier Parts and Accessories Getting to Know your Copier Chapter 2 Inside Copier 2 1 3 7 6 5 4 1142O012AA 2 Original : Place the original along these Scales for correct Width/Length Scale positioning. ➭ p. 28 Original Pad : Holds the original in position on the Original Glass. 3 Original Glass 1 4 5 6 7 : Place the original face down on this Glass. ➭ p.
11 2. Copier Parts and Accessories 9 13 10 12 11 1142O013AA 8 Upper Half of Copier 9 Imaging Unit : The copier main body can be divided into two parts, the upper and lower. The Upper Half can be swung upward. ➭ p. 77 : Converts the original image to the copy image. 10 Imaging Unit Lock : Operate when replacing the Imaging Unit. ➭ p. 84 Release Lever : Turn ON to prevent condensation from forming on 11 Dehumidifier Switch the PC Drum when power is turned OFF.
12 2. Copier Parts and Accessories Automatic Document Feeder AF-5 2 Chapter 2 1 Getting to Know your Copier 3 4 1152O040AA 1 2 3 4 Document Feed Tray Extender Document Feed Tray Document Guide Plate Document Exit Tray : Pull out when loading large-size originals. ➭ p. 31 : Load the originals face up on this tray. ➭ p. 31 : Slide the plate as necessary to the size of the originals. ➭ p. 31 : Receives originals that are automatically ejected from AF-5.
13 2. Copier Parts and Accessories 10-Bin Sorter S-106 Chapter 2 2 Getting to Know your Copier 1 1142O014AA 1 Sorter Bins 2 Lock Release Lever : Press to unlock the Sorter. ➭ p. 82 : Hold sorted copies. Multi Bypass Tray MB-4 1 3 2 1139O1090A 1 2 3 Paper Guide Plate : Slide as necessary to the size of the copy paper. ➭ p. 50 Multi Bypass Tray : Load your paper on this Tray. It allows you to make copies continuously on paper fed from this Tray. ➭ p.
14 3. Control Panel Keys and Indicators Control Panel 1 2 3 5 4 6 Chapter 2 Meter Count Toner Auto Size Getting to Know your Copier Paper Drum Dehumidify Sort A3 A4 A4 A5 @ @ @ @ @ @ B4 @ FLS. @ Inch 50%~20 Auto Photo Book Lighter Darker Auto/Photo A 23 1 2 3 4 5 6 7 8 9 10 11 12 22 21 20 19 18 Clip Tray: Use this tray to put the paper clips used with the documents. Drum Dehumidify Key: Press to remove condensation formed on the surface of the PC Drum. ➭ p.
15 3. Control Panel Keys and Indicators 10 % 50%~200% 1 2 3 4 5 6 7 8 9 0 C 141% A4 @ A3 115% B4 @ A3 100% @ @ @Full Size 81% B4 @ A4 70% A3 @ A4 Chapter 2 9 8 100% 17 16 15 14 13 12 1152O003DA 1152O003DA 11 13 Stop Key: Press to stop a multi-copy cycle. ➭ p. 48 14 Start Key: Press to start a copy cycle. ➭ p. 48 15 Enlargement Key: Press to select a desired fixed enlargement ratio. ➭ p. 35 16 Full Size Key: 17 18 19 20 21 22 23 Press to select full size (100%). ➭ p.
16 3. Control Panel Keys and Indicators Display 1 2 Getting to Know your Copier Chapter 2 Meter Count Toner Paper Drum Dehumidify Auto Size Sort Book A3 A4 A4 A5 @ @ @ @ 3 @ @ B4 @ FLS. @ Inch Auto Photo Lighter Darker Auto/Photo 4 1 % 50%~200% 141% A4 @ A3 115% B4 @ A3 100% @ @ @Full Size 81% B4 @ A4 70% A3 @ A4 1152O030DA Monitor Display • Paper Source Indicator Shows the paper source which is currently selected for use. ➭ p.
17 3. Control Panel Keys and Indicators Indicator • Add Toner Indicator Indicates that the Toner Bottle is running out of toner. Replace the Toner Bottle as soon as possible. ➭ p. 70 1142O021AA 1142O021AA • I. U. Service Life Indicator Indicates that the Imaging Unit needs replacement. Replace the Imaging Unit. ➭ p. 84 1142O022AA 1142O022AA 2 Paper Information Display • Paper Size Indicators Show the size of paper currently loaded in the Drawer. ➭ p.
18 3. Control Panel Keys and Indicators 3 Zoom Ratio Indicator / Multi-Copy Display Zoom Ratio Indicator Multi-Copy Display • Example Chapter 2 Getting to Know your Copier : Each shows the following data. Zoom ratio: 100% No.
19 4. Turning ON and OFF, and Resetting the Copier Turning ON and OFF 1142O026AA NOTE The Auto Shut OFF function will automatically shut down the copier a given period of time after the last activity. The initial setting is 30 minutes. Useful Tip The period of time can be changed by using the User’s Choice. ➭ p. 63 When Copier is Turned ON Blinking Orange Turns Green • The Start Key blinks orange, indicating that the copier is now warming up. • In about 30 sec., the Start key turns green.
20 4. Turning ON and OFF, and Resetting the Copier Auto Copy Start Function (Only when Automatic Document Feeder is used) Chapter 2 The Auto Copy Start Function allows a copy process to be started as soon as the copier completes warming up. Using the Function 1 2 3 4 5 6 7 8 9 Getting to Know your Copier 0 Start Energy Saver 1 When you load the originals onto the Automatic Document Feeder while the copier is warming up, the Start Key turns to green and blinks.
21 4. Turning ON and OFF, and Resetting the Copier Useful Tip The time for the copier to enter the Energy Saver Mode can be selected from 1 to 120 min. by using User’s Choice. ➭ p. 62 NOTE The copier is shut down if the Auto Shut OFF function activates while the copier is in the Energy Saver Mode. Entering The Energy Saver Mode • Press the Energy Saver Key on the control panel. Energy Saver ◆ All control panel Indicators go out, except that the Start Key and the Energy Saver Key which remain lit green.
22 4. Turning ON and OFF, and Resetting the Copier Initial Mode and Panel Resetting Chapter 2 Initial Mode When the Power Switch is turned ON, the initial settings are indicated on the control panel. * The initial settings serve as the reference for all control panel settings to be later made. Getting to Know your Copier Meter Count Toner Paper Drum Dehumidify Auto Size Sort Book A3 A4 A4 A5 @ @ @ @ @ @ B4 @ FLS.
23 4. Turning ON and OFF, and Resetting the Copier Panel Resetting The Panel Reset Key resets all control panel settings to default settings including the number of copies to be made and zoom ratio. 1139O4782A 1139O4782A Useful Tip The Panel Reset Key enables you to cancel all previous settings efficiently. To avoid miscopy, try to press the Panel Reset Key before attempting to make any setting for your own job.
24
25 Chapter 3 1. Copying Overview p. 26 2. Copying Procedure Placing Originals p. 28 Using the Automatic Document Feeder AF-5 p. 30 Checking the Copy Paper Size and Selecting the Paper Source p.33 Zoom Ratio • Types of Zoom Ratios p. 34 • Auto Size Mode p. 37 • Zoom Ratio Table (Original Size to Copy Paper Size) p. 39 Image Density p. 40 Book Copying p. 42 Finishing Modes • Finishing Modes p. 44 • Selecting the Finishing Mode p. 45 • Auto Dual Function P. 46 Number of Copies p.
26 1. Copying Overview • Place the original in position (step 1), set the number of copies to be made (step 7), and press the Start Key (step 8). This will allow you to make a full-size copy or copies on paper of the same size as the original. The control panel selection ( ) you make will change the magnification ratio and the image density. 1. Placing the Original • Load the Originals face up on the Automatic Document Feeder. ➭ p.
27 1. Copying Overview 4. Setting the Image Densitry • Set the image density in the Manual Exposure Mode. ➭ p. 41 • Select the Auto Exposure Mode or Photo Mode. ➭ p. 41 Auto Photo Auto Photo Lighter Darker Auto/Photo Lighter Darker Auto/Photo A A To copy from a book 5. Selecting Book Copying • Press the Book Key to select the Book Copying Mode. ➭ p. 42 Book 1142O097CC To sort copies Chapter 3 1152O023CA 1152O022CA 1142O097CC 6. Selecting the Finishing Mode • Select Sort Mode.
28 2. Copying Procedure Placing Originals Place the original face down on the Original Glass. Different methods are used to load the originals depending on the type of originals and whether the copier is equipped with an Automatic Document Feeder (option). Making Copies 1 Raise the Original Cover. 2 Gently lower the Original Cover. 1 2 Place the original in the same way as the sheet originals.
29 2. Copying Procedure Book Original *"Book original" refers to an open bound original. Position the higher-numbered page on the Original Width Scale end. NOTES Making Copies 1134O037AA properly will result in copies with pages in incorrect order. • Do not place an original weighing more than 3kg on the Original Glass, as an image problem could result.
30 2. Copying Procedure Using the Automatic Document Feeder AF-5 The Automatic Document Feeder AF-5 automatically feeds sheet originals placed on the Document Feed Tray one by one. After the copy cycle has been completed, it automatically ejects the originals onto the Exit Tray. Making Copies Chapter 3 Some originals may not be suitable for reliable operation in the AF-5. Here is a guide.
31 2. Copying Procedure Loading Standard Size Originals 1 Slide the Document Guide Plate to the size of the originals. *Using the large size originals, flap up the Document Feed Tray Extender. 2 Load a neat stack of originals face up on the Document Feed Tray. Chapter 3 1151O015AA 1151O017AA • The maximum number of originals that can be loaded A4 or smaller : Up to 50 A3 or B4 : Up to 30 • Make sure that the top level of the original stack does not exceed the ▼ marking.
32 2. Copying Procedure Single Automatic Document Feeding Mode (SADF Mode) Making Copies Chapter 3 This is the mode in which you load your originals one by one onto the Automatic Document Feeder to make a copy or copies from it. When you load the original, the copier automatically starts the copy cycle. Originals available for the SADF Mode. • Type : Plain paper • Thickness : 35g/m2 to 200g/m2 • Size : A3 to A5 1 Open the Document Feed Table and slide the Guide Plate to the size of the orginal.
33 2. Copying Procedure Checking the Copy Paper Size and Selecting the Paper Source Paper Drum Dehumidify Auto Size Sort A3 A4 A4 A5 @ @ @ @ @ @ B4 @ FLS. @ Inch Auto Photo Book Lighter Darker Auto/Photo % 50%~200% 141% A4 @ A3 115% B4 @ A3 100% @ @ @Full Size 81% B4 @ A4 70% A3 @ A4 1152O031DA When the copier is not equipped with the Multi Bypass Tray, it is necessary to check that the desired paper size is loaded into the Drawer.
34 2. Copying Procedure Zoom Ratio Meter Count Toner Paper Drum Dehumidify Making Copies Chapter 3 Auto Size Sort A3 A4 A4 A5 @ @ @ @ @ @ B4 @ FLS. @ Inch Auto Photo Book Lighter Darker Auto/Photo % 50%~200% 141% A4 @ A3 115% B4 @ A3 100% @ @ @Full Size 81% B4 @ A4 70% A3 @ A4 1152O031DA The zoom ratio can be set manually by the operator when in the Manual Mode or will be set automatically by the copier when in the Auto Size Mode. Select the appropriate mode according to your needs.
35 2. Copying Procedure Selecting the Fixed Zoom Ratios Press the Reduction, Full Size, or Enlargement Key to select a fixed zoom ratio of your choice. 100% Each time the Reduction Key is pressed, it selects a new reduction ratio. A4 A3 B4 A3 Full Size B4 A4 A3 A4 100% * The Zoom Ratio Indicator displays 1142O140DC 1142O140DB 141% 115% 100% 81% 70% the actual percentage of the selected ratio. Each time the Enlargement Key is pressed, it selects a new enlargement ratio.
36 2. Copying Procedure Setting a Zoom Ratio < > < Hold down the Zoom Down or Up Key until the desired zoom ratio is reached. Zoom Down Key makes the ratio smaller Zoom Up Key makes the ratio greater > 50%~200% Making Copies Chapter 3 1139O3640A 1139O3640A Zoom range: 50% to 200% Useful Tip To save time, first select the fixed ratio nearest to the target zoom ratio before using the Zoom Up or Down Key.
37 2. Copying Procedure Auto Size Mode • The Auto Size Mode can be selected only when the copier is equipped with the Automatic Document Feeder. • In the Auto Size Mode, the copier automatically selects the correct zoom ratio according to the original size and copy paper size. Selecting the Auto Size Mode 1142O096CC Chapter 3 Auto Size Press the Auto Size Mode Key. 1142O096CC The Zoom Ratio Indicator shows . %% 50%~200% 1142O046AA 1142O046AA 2 Paper A4 Check the copy paper size. ➭ p.
38 2. Copying Procedure NOTE Making Copies Chapter 3 The copier has been factory-set to automatically select the Manual Mode. This default setting can be changed to the Auto Size Mode by using the User’s Choice. ➭ p.
39 2.
40 2. Copying Procedure Image Density Meter Count Toner Paper Drum Dehumidify Auto Size Sort A3 A4 A4 A5 @ @ @ @ @ @ B4 @ FLS. @ Inch Auto Photo Book Making Copies Chapter 3 Lighter Darker Auto/Photo % 50%~200% 141% A4 @ A3 115% B4 @ A3 100% @ @ @Full Size 81% B4 @ A4 70% A3 @ A4 1152O031DA The image density level of copies can be adjusted either in the Auto Exposure Mode, Manual Exposure Mode or Photo Mode. Select the appropriate mode according to your particular needs.
41 2. Copying Procedure Lighter Darker Auto/Photo A 1152O023CA Manual Exposure Mode Hold down the Exposure Control Key < or > until the desired exposure level is reached. Auto Photo Lighter Darker Auto/Photo A 1152O022CA To make the image darker : Press or hold down the Exposure Control Key > . To make the image lighter : Press or hold down the Exposure Control Key < . Photo Mode Press the Auto Exposure Mode Key A as necessary to light up the Photo Mode Indicator ❍ Photo .
42 2. Copying Procedure Book Copying Original Auto Size Sort Copy Book 1139O1990A • Select Book Copying when you want to make a 1-sided copy of each page of an open book. Chapter 3 1142O150CA 1142O150CA Selecting the Book Copying Mode Making Copies 1 Position the higher-numbered page on the Original Width Scale end. If the book is thick, you can make copies with the Original Cover raised. * "Book original" refers to an 1134O037AA open bound original.
43 2. Copying Procedure NOTE • If paper other than A4 crosswise @ @ B4 @ FLS. @ Inch 1152O032DA 1139O1460A A4 Crosswise In such a case, load paper of the same size and in the same direction of each page of a book into the Drawer. Chapter 3 @ @ @ @ Making Copies Paper A3 A4 A4 A5 paper is loaded into the Drawer when the Book Copying Mode is selected, the Drawer Indicator and the corresponding Paper Size Indicator blink on the Control Panel.
44 2. Copying Procedure Finishing Modes Auto Size Sort There are two different finishing modes: Non-Sort and Sort. Book Select the appropriate mode according to your particular needs. 1142O151CA Chapter 3 1142O151CA Finishing Modes • In the Non-Sort Mode, all copies are Making Copies Non-Sort Originals Copies fed out onto the 1st Bin without being sorted.
45 2. Copying Procedure Selecting the Finishing Mode Press the Finishing Mode Select Key to select the desired mode. Sort * If the Sort Mode is selected, the Sort Indicator lights. 1142O098CC NOTES • The Sort Mode cannot be selected unless the copier is equipped with the Chapter 3 1142O098CC If this capacity is exceeded, the Remove Copies Indicator blinks on the Monitor Display and the Start Key turns orange, inhibiting the initiation of a new copy cycle.
46 2. Copying Procedure Auto Dual Function Each of the Sorter Bins holds up to 25 sheets of paper. However, the Auto Dual Function allows sorting of copies of up to 50 originals under certain conditions. Auto Dual Function in the Sort Mode Making Copies Chapter 3 When 5 or less copies are made from an original set consisting of more than 25 originals in the Sort Mode, the Sorter is automatically switched into the Auto Dual Function Mode using the 6th to 10th Bins.
47 2. Copying Procedure Number of Copies Meter Count Toner Paper Drum Dehumidify Auto Size Sort Book A3 A4 A4 A5 @ @ @ @ @ @ B4 @ FLS. @ Inch Auto Photo % 50%~200% Lighter Darker Auto/Photo 141% A4 @ A3 115% B4 @ A3 100% @ @ @Full Size 81% B4 @ A4 70% A3 @ A4 A 100% 1 2 3 4 5 6 7 8 9 0 C 1 2 3 4 5 6 7 8 9 0 C Using the Key Pad, enter the number of copies to be made. * The maximum number that can be set is 99.
48 2. Copying Procedure Starting the Copy Cycle Meter Count Toner Paper Drum Dehumidify Sort Book @ @ @ @ @ @ B4 @ FLS. @ Inch Auto Photo % 50%~200% Lighter Darker Auto/Photo 141% A4 @ A3 115% B4 @ A3 100% @ @ @Full Size 81% B4 @ A4 70% A3 @ A4 A 100% 1 2 3 4 5 6 7 8 9 0 C 1152O033DA Starting the Copy Cycle Making Copies Chapter 3 Auto Size A3 A4 A4 A5 1 Check the control panel to make sure that you have set up your copy job correctly.
49 2. Copying Procedure Manual Bypass Copying • Plain paper: Approx. 50 sheets • Plain paper (once-copied paper) ... Up to 20 sheets • Heavyweight paper, transparencies, translucent paper: Approx. 20 sheets IMPORTANT When making multiple copies using OHP transparencies, set the Copy Tray into the upper position if there is no Sorter or Staple Sorter mounted. Using the Manual Bypass Tray 1139O0150A 1 Place the original on the Original Glass and make the control panel settings.
50 2. Copying Procedure Using the Multi Bypass Tray (Option) 1 Place the original on the Original Glass and make the control panel settings. 2 Swing down the Multi Bypass Tray and slide the Paper Guide Plate to the size of the copy paper. 1139O0130A Chapter 3 NOTE Pull out the Multi Bypass Tray Extender if you are using larger paper. Making Copies 3 Load a neat stack of copy paper on the Tray and insert it into the copier until it stops.
51 Chapter 4 Auxiliary Functions 1. Checking the Total Number of Copies Mode p. 52 2. Toner Replenisher Function (Increasing the Image Density) p. 54 3. Drum Dehumidifier Function p. 55 4. User’s Choice p. 56 Auxiliary Functions Chapter 4 This Chapter explains about the Auxiliary functions that can be used for specific purposes.
52 1. Checking the Total Number of Copies Mode This function allows you to check the total count of the two counters of the copier. Meter Count Toner Drum Dehumidify 1142O152CA 1142O152CA Auxiliary Functions Chapter 4 Types of Counters • Total Counter : Shows the total number of copies made since • Size Counter : Shows the number of copies made on paper of the installation of the copier. a size preset by the Technical Representative.
53 1. Checking the Total Number of Copies Mode Using the Meter Count Function Meter Count 1 Press the Meter Count Key once. 2 Press the Meter Count Key again. The count of the Size Counter is shown across the Zoom Ratio Indicator and Multi-Copy Display. 3 Press the Meter Count Key once again. Toner Drum Dehumidify The count of the Total Counter is shown across the Zoom Ratio Indicator and Multi-Copy Display.
54 2. Toner Replenisher Function 2. (Increasing the Image Density) The copier tends to exhaust the supply of toner rapidly when making a number of copies from an original with dark solid areas. As a result, the image density of the copy will become lighter. In such a case, you can use the Toner Replenisher function to regain the normal image density quickly.
55 3. Drum Dehumidifier Function During high humidity periods or when there are sudden rapid changes in humidity (especially when you are using a heater in winter), condensation*1 could form on the surface of the PC Drum*2, resulting in blotchy copies. In such instances, use the Drum Dehumidify Key to dry the surface of the PC Drum.
56 4. User’s Choice The copier has been set so that the most frequently used settings are automatically selected in the initial mode. % 50%~200% 141% 115% 100% 81% 70% The User’s Choice allows you to select the default settings which are automatically selected in the initial mode according to your own needs.
57 4. User’s Choice Description of Each User’s Choice Function U-4 Lightweight Original Mode • Select either one of the following settings when the copier is equipped with the Automatic Document Feeder. If "0" is selected: You can make copies only from originals of standard weight (Normal Mode). If "1" is selected: You can make copies from lightweight originals (40g/m2 to 50g/m2 ), as well as originals of the standard weight (Lightweight Original Mode).
58 4. User’s Choice U-13 Default auto exposure level • Determines the default exposure level in the Auto Exposure Mode. Setting Value Initial Setting Description 46 Low, level 4 47 48 Low, level 3 Low, level 2 49 50 51 Low, level 1 Standard High, level 1 52 High, level 2 Chapter 4 * When the exposure level is "Low," the greater the level number is, the lower the exposure level. When the exposure level is "High," the greater the level number is, the higher the exposure level.
59 4. User’s Choice U-14 Default exposure mode/level • Determines the default exposure mode, either Auto or Manual, selected when the control panel settings are reset. If Auto is selected, this function also allows you to specify the default exposure level (EXP) in the Manual Exposure Mode, after the Auto Exposure Mode has been canceled. If Manual is selected, the function also allows you to specify the default exposure level (EXP) in the Manual Exposure Mode.
60 4.
61 4. User’s Choice U-15 Default Finishing mode • Determines the default finishing mode when the copier is equipped with the Sorter. Setting Value 0 1 Description Initial Setting Non-Sort Sort Setting Value 0 1 Description Auto Panel Reset is not activated. Auto Panel Reset is activated (after 30 sec.) 2 Auto Panel Reset is activated (after 60 sec.) Initial Setting Auxiliary Functions If "0" is selected: The control panel settings remain valid even after 60 seconds.
62 4. User’s Choice U-21 Energy Saver ON Timing • Select whether or not to set the copier into the Energy Saver mode after the lapse of a given period of time after a copy cycle has been completed or a key on the control panel has been operated. • The period of time can fall within the range 1 to 120 min. * The initial setting is 15 min. Auxiliary Functions Chapter 4 Setting Value 1 2 3 : : 98 99 Description Enabled : Enabled : Enabled : : : Enabled : Enabled : Initial Setting 1 min. 2 min. 3 min.
63 4. User’s Choice U-24 Sort/Non-Sort Auto Switching ON/OFF • Specifies whether to enable automatic switching between the Sort and Non-Sort Mode under the following conditions when the copier is equipped with the Sorter and the Automatic Document Feeder. Conditions • The copy cycle is initiated using a single original in the Sort Mode. • The copy cycle is initiated to make two or more copies using two or more originals in the Non-Sort Mode.
64 4. User’s Choice Making the User’s Choice Mode Settings 1 Panel Reset Keep pressing the Panel Reset Key for about 3 seconds. * Uappears on the Zoom Ratio Indicator, and the indicator on the Multi-Copy Display goes out. 1139O4782A 1139O4782A Zoom Ratio Indicator Multi-Copy Display 1139O3860A 1139O3860A Chapter 4 1139O3850A 1139O3850A 1 2 3 4 5 6 7 8 9 0 C 2 Using the Key Pad, enter the desired Choice Code number.
65 4. User’s Choice 3 Press the Start Key. * This causes the current setting of that particular choice code to be shown on the Multi-Copy Display. 1139O2360A Multi-Copy Display Zoom Ratio Indicator 1152O050AA 1152O050AA 3 5 6 7 8 9 0 C 4 * This clears the current setting. 1142O169AA 1142O169AA Zoom Ratio Indicator 1152O050AA 1152O050AA Multi-Copy Display 1139O3860A 1139O3860A Chapter 4 2 4 Press the Clear Key.
66 4. User’s Choice 1 2 3 4 5 6 7 8 9 0 C 5 Press the appropriate Key Pad to enter the new setting. See pages 57-63 for the Choice Code. * The Multi-Copy Display shows the new setting. 1142O171AA 1142O171AA Zoom Ratio Indicator Multi-Copy Display 1152O050AA 1152O050AA 1139O3890A 1139O3890A Auxiliary Functions Chapter 4 6 Press the Start Key. * This enters the new setting. Repeat steps 2 to 6 to make new settings for other User’s Choices.
67 Chapter 5 When an Indicator Lights Up (Replenishing Supplies, Clearing Misfeeds, and Correcting a Closure Failure) Call-Tech.-Rep. Indicator p. 83 When an Indicator Lights Up 1. Quick Reference for Indicator Lights p. 68 2. Detailed Instructions for Indicator Lights Add Toner Indicator p. 70 Add Paper Indicator p. 72 Closure Failure Indicator p. 75 Misfeed Indicator • Misfeed Indicator and Monitor Display p. 76 • Misfeed Clearing Procedure : Copier p. 77 : Automatic Document Feeder p. 80 : Sorter p.
68 1. Quick Reference for Indicator Lights Meter Count Toner Paper Drum Dehumidify Auto Size Sort A3 A4 A4 A5 @ @ @ @ @ @ B4 @ FLS. @ Inch Auto Photo Book Lighter Darker Auto/Photo % 50%~200% 141% A4 @ A3 115% B4 @ A3 100% @ @ @Full Size 81% B4 @ A4 70% A3 @ A4 1152O034DA 1152O034DA When the copier encounters any of the following conditions, a corresponding warning indicator lights up.
69 1. Quick Reference for Indicator Lights Action If the Call-Tech.-Rep. Indicator remains lit even after you have reset it, call your Technical Representative. ➭ p. 83 Chapter 5 1139O3940A Copier State The copier has developed a technical malfunction. When an Indicator Lights Up Indicator Call-Tech.-Rep.
70 2. Detailed Instructions for Indicator Lights Add Toner Indicator The Add Toner Indicator lights up when toner in the Toner Bottle is running out. Once the Indicator lights up, replace the Toner Bottle with a new one as soon as possible by following the procedure given below. 1142O021AB 1142O021AB When an Indicator Lights Up Chapter 5 Replacing the Toner Bottle 1 Open the Front Door. 2 Swing open the Toner Bottle Holder and pull out the Toner Bottle. 3 Shake a new Toner Bottle well.
71 2. Detailed Instructions for Indicator Lights 4 With the Seal on the Toner Bottle facing up, slowly peel off the Seal as illustrated. NOTE Be careful, some toner may puff out from the bottle. 1139O1390A 5 Ensuring that the arrow ( ) on the Toner Bottle is facing toward you, insert the Bottle into position. NOTE 6 Swing the Toner Bottle Holder closed and close the Front Door.
72 2. Detailed Instructions for Indicator Lights Add Paper Indicator Monitor Display Add Paper Indicator When the Drawer or the Multi Bypass Tray has run out of paper, the Add Paper Indicator lights up. At this time, you cannot start a new copy cycle. 1139O3910A Use the following procedure to load paper into the Drawer or the Multi Bypass Tray.
73 2. Detailed Instructions for Indicator Lights 4 Load the paper stack into the Drawer so that its front side faces down. Make sure that the paper stack rests under the two catches of the Drawer. NOTE 1151O094AA Slide the Edge Guide and Trailing Edge Stop tightly up against the paper. Gently slide the Drawer back in. 1139O0420A NOTE When loading Inch Size paper into the Drawer, flip the Marketing Area Switch, located in the rear left corner of the Drawer to "Inch".
74 2. Detailed Instructions for Indicator Lights Adding Paper (Multi Bypass Tray) Monitor Display Add Paper Indicator The indications on the left show that the Multi Bypass Tray has run out of paper. 1139O3910A 1142O061AA 1142O061AA Front Side 1 Unwrap the package of the copy paper and fan the paper stack thoroughly. 2 Load the paper stack onto the Tray so that its front side faces up and insert it until it stops.
75 2. Detailed Instructions for Indicator Lights Closure Failure Indicator The Closure Failure Indicator lights up if a copier door is left open, or an option is not attached properly. The Monitor Display shows the location of the closure failure. At this time, you can no longer start a new copy cycle. Correct the closure failure by following the procedure given below. 1142O018AA 1142O018AA 1142O065AA 1142O064AA Chapter 5 1142O018AA Check Locations Check that the Right Door or Front Door is closed.
76 2. Detailed Instructions for Indicator Lights Misfeed Indicator If a paper misfeed occurs during a copy cycle, that copy cycle stops. The Misfeed Indicator lights up and the Monitor Display shows the location. At this time, you cannot start a new copy cycle. 1142O019AB 1142O019AB Misfeed Indicator and Monitor Display Check the Monitor Display for the location of the misfeed, and clear the misfed sheet of paper according to the procedure given for each location.
77 2. Detailed Instructions for Indicator Lights Misfeed Clearing Procedure: Copier NOTE Be careful not to touch the areas marked with High Voltage and Caution: HOT with bare hands. 1142O019AB 1142O019AB Unload the paper stack from the Multi Bypass Tray. Open the Front Door and turn the Lock Release Lever counterclockwise to unlock and swing up the Upper Half of the copier.
78 2. Detailed Instructions for Indicator Lights 2 1142O073AA Holding up the Fusing Unit, pull out the sheet of paper . CAUTION: HOT The Fusing Unit and its surrounding areas may be extremely hot. DO NOT touch any part except the Fusing Uinit Handle (yellow). 3 Remove any sheet of paper from the Transport Section. 4 Open the Right Door. 5 6 Pull out the sheet of paper from the Paper Take-Up Section.
79 2. Detailed Instructions for Indicator Lights 7 Gently swing down and lock the Upper Half of the copier. Then close the Front Door. 1142O076AA 8 Slide out the Drawer and unload the paper from the Drawer. Next, push down the Paper Lifting Plate until it is locked into position. 9 Fan the paper and reload it. 1142O060AA NOTE Make sure that the paper stack rests under the two catches of the Drawer.
80 2. Detailed Instructions for Indicator Lights Misfeed Clearing Procedure: Automatic Document Feeder There is a misfeed original in the Automatic Document Feeder. 1142O068AC 1142O068AC 1 Remove the original stack from the Document Feed Tray. 2 3 Swing open Document Feed Unit Door F1 , and gently pull out the original. 4 Carefully pull out the original from the Document Exit Unit. When an Indicator Lights Up Chapter 5 1151O097AA Close F1 .
81 2. Detailed Instructions for Indicator Lights 5 Raise the Automatic Document Feeder. Opening the Document Feed Unit Guide Plate, gently pull out the original from the Unit. 6 Remove the original from the Original Glass, and lower the Automatic Document Feeder. 7 Return the number of originals indicated on the Display at the back of the original stack removed in step 1 and reload it onto the Document Feed Tray.
82 2. Detailed Instructions for Indicator Lights Misfeed Clearing Procedure: Sorter There is a misfeed sheet of paper in the 10-Bin Sorter. 1142O069AC 1142O069AC 1 Hold the Lock Release Lever of the Sorter and slide the Sorter away from the copier. 2 Pull out the copy from the Transport Section. 3 Slide the Sorter back to the copier.
83 2. Detailed Instructions for Indicator Lights Call-Tech.-Rep. Indicator Meter Count Toner Paper Drum Dehumidify Auto Size Sort A3 A4 A4 A5 @ @ @ @ @ @ B4 @ FLS. @ Inch % 50%~200% Auto Photo Book 141% A4 @ A3 115% B4 @ A3 100% @ @ @Full Size 81% B4 @ A4 70% A3 @ A4 Lighter Darker Auto/Photo 1152O029DA When a malfunction occurs in the copier, the Call-Tech.-Rep. Indicator lights up and the corresponding malfunction code appears across the Zoom Ratio Indicator and Multi-Copy Display.
84 2. Detailed Instructions for Indicator Lights I.U. Service Life Indicator When time is about to come when the Imaging Unit needs replacement, the I.U. Service Life Indicator starts blinking to prompt you to replace it with a new one. Replace the Imaging Unit by following the procedure given below. 1142O174CA Chapter 5 When 2,500 more copies are made with Add Toner Indicator lighting up, or 7,500 more copies are made, after the I.U. Service Life Indicator has started blinking, the I.U.
85 2. Detailed Instructions for Indicator Lights Precautions for Handling • Do not leave the I. U. in a bright place. 1139O6032A • Do not store the I. U. in a hot place of 40°C (104°F) or more. place or subject to water splash. 1139O6052A • Do not store the I. U. upside down or tilted. Do not subject the I. U. to vibration. 1139O6062A When an Indicator Lights Up • Do not store the I. U.
86 2. Detailed Instructions for Indicator Lights Removing the I. U. from copier 1 Open the Front Door. Turn the Lock Release Lever counterclockwise to swing up the Upper Half of the copier. 1142O071AA Unlock and swing up the Upper Half of the copier. Then lock Stopper M2 . When an Indicator Lights Up Chapter 5 1142O072AA 2 Turn the I. U. Lock Release Lever and, while holding it down, pull the I. U. halfway out from the copier.
87 2. Detailed Instructions for Indicator Lights Unpacking the I. U. Starter Bottle I. U. 1 2 3 Peel off the piece of tape and open the Carton Box. 1 Take the I. U. out of the bag. 2 Peel off the three pieces of tape and packing materials. Take the Starter Bottle out from the Carton Box. Take the I. U. with its bag out of the Carton Box. 4445U002AA 4445U003AA When an Indicator Lights Up Setting up the I. U.
88 2. Detailed Instructions for Indicator Lights 3 Carefully pull the polyester tape from the I. U.. 4 Remove the Cap from the I. U. and re-fit it to the used I. U. as shown in the illustration. 5 Align the I. U. with the Rails in the copier. 6 Slide the I. U. all the way into the copier.
89 2. Detailed Instructions for Indicator Lights 7 Be sure to push the I. U. into the locked position until a click is heard. Then, check to see the position of Lock Release Lever, as shown in the illustration. NOTE 4445U005AA An improperly installed I. U. could be a cause of copier malfunction. 8 Lower the Upper Half of the copier and push it into the locked position by pushing down on the portion marked with "Push Down Here Only".
90 2. Detailed Instructions for Indicator Lights 1 Swing out the Bottle Holder. 2 Hold the Starter Bottle so that its tab is on the upper side, shake it well. Chapter 5 3 Peel off the tape from the Starter Bottle. When an Indicator Lights Up Charging the Copier with Starter and Toner 4 Align the markings on the Starter Bottle with the upper side of the Bottle Holder and slide the Bottle into position.
91 2. Detailed Instructions for Indicator Lights 5 6 7 Close the Front Door. 8 The copier automatically start the charging cycle for approximately 5 minutes. 1139O6012A Plug the Power Cord into the Wall Outlet. Turn ON the Power Switch. This will cause the wait indicator to be shown on the control panel. 1139U011AA When the copier has been completely charged with Starter, the indication on the Magnification Ratio Indicator changes to "100" and the cycle stops.
92 2. Detailed Instructions for Indicator Lights 9 Swing down the Front Door, swing out the Bottle Holder and remove the Starter Bottle. 10 Hold the Toner Bottle so that its tab is on the upper side, shake it well and peel off the tape. 4445U009AA Once the tape has been removed, hold the Bottle so that its Toner Port faces up.
93 Chapter 6 Troubleshooting 2. The Copier is not functioning as designed p. 98 • None of the Control Panel Indicators light up • Pressing the Start Key does not start the copy cycle • The Copier is not activated when the Power Switch is turned ON Troubleshooting 1. When this Type of Copy is Produced p.
94 1. When this Type of Copy is Produced Symptom The image is too light. Possible Cause The exposure level for the Auto Exposure Mode is set at one of the "Light" levels. The manual exposure level is set on the lighter side. You have been making copies from a photo or an original with a large dark area. 1074O108 The Toner Bottle has just been replaced. The Add Toner Indicator on the Monitor Display is lit up. Add Toner Indicator 1139O3270A The paper is damp.
95 1. When this Type of Copy is Produced Action Change the setting of the User’s Choice Mode U-13 (Default Auto Exposure Level). ➭ p. 58 Cancel the Auto Exposure Mode and select the Manual Exposure Mode to adjust the exposure level and obtain a darker image. ➭ p. 41 Press the Exposure Control Key (Darker) as necessary to obtain a darker image. ➭ p. 41 The copier needs more toner. Press the Auxiliary Toner Replenishing Key as many times as required to obtain the desired image density. ➭ p.
96 1. When this Type of Copy is Produced Symptom The copy has lines. Possible Cause The Corona Units are dirty. 1139O1670A The copy has dark specks or spots. The Original Glass is dirty. The Original Pad or Document Feed Belt is dirty. The original is very thin or highly transparent. The original is two-sided. 1139O1660A 1139O1690A The image on the copy is not aligned properly. Troubleshooting Chapter 6 The edge of the copy is dirty. The Original Pad or Document Feed Belt is dirty.
97 1. When this Type of Copy is Produced Action Using the Corona Unit Cleaning Levers, clean the Corona Units. ➭ p. 112 Wipe the Original Glass clean with a soft dry cloth. ➭ p. 110 Wipe the Original Pad or Document Transport Belt clean with a soft cloth dampened with mild home detergent. ➭ pp. 110, 113 Place a blank sheet of paper over the original. ➭ p. 28 The information on the back side of a two-sided, thin original may be slightly reproduced on the copy.
98 2. The Copier is not functioning as designed Symptom None of the Control Panel Indicators light up. Check for: Is the Start Key lit up green? The copier is in the Auto Shut OFF Mode. Pressing the Start Key does not start the copy cycle. Is the Start Key blinking Orange? Is any of the following Indicators lit up? 1139O3910A The Copier is not activated when the Power Switch is turned ON.
99 2. The Copier is not Functioning as Designed Action The copier is in the Energy Saver Mode. Press any Key on the Control Panel to cancel the Energy Saver Mode. Turn the Power Switch ON. The copier is now warming up. Please wait. ➭ p. 19 Take the necessary steps for each Indicator. ➭ p. 68 ➭ p. 21 Plug the power cord into the power outlet. Troubleshooting Chapter 6 Close the room circuit breaker.
100 Troubleshooting Chapter 6 2.
101 Chapter 7 Specifications Chapter 7 1. Copier p. 102 2. Automatic Document Feeder p. 104 3. 10 Bin Sorter p. 105 4. Multi Bypass Tray p. 106 Specifications This Chapter gives complete specifications of the copier system and options.
102 1. Copier Name Copier EP1083 Type Desk Top Copier Platen Type Stationary Photoconductor OPC Copying System Electrostatic Dry Powdered Image Transfer to Plain Paper Developing System Micro-Toning System Fusing System Lamp-Heated Roller Types of Original Sheets, Books, and other three-dimensional objects Maximum Original Size: A3 Lengthwise Maximum Original Weight: 3kg.
103 Fixed ratios Full size: 1:1±0.5% Reduction Ratios: 50%, 70%, 81% Enlargement Ratios: 115%, 141%, 200% Zoom ratios: From 50% to 200% in 1% increments Multiple Copy Up to 99 copies (Count-Down system) Exposure Control Auto, Manual and Photo Mode Power Requirements AC 115V, 120V, 127V, AC 220V-240V, 50/60Hz Power Consumption 1.3 kW (Max.
Chapter 7 Specifications 104 2.
105 3. 10 Bin Sorter No.
106 4.
107 Chapter 8 Miscellaneous This Chapter explains about care of the copier and the various possible combinations of functions. Chapter 8 Miscellaneous 1. Care of the Copier • Daily Checks p. 108 • Cleaning p. 110 2. Description of Copy Paper Size p. 114 3. Zoom Ratio Table (Original Size to Copy Paper Size) p. 115 4. Index p.
108 1. Care of the Copier To keep your copier in good shape at all times, make the following daily checks and cleaning. Daily Checks Power Cord, Communications Cable, Ground Cable Item Is the copier placed on its power cord or other Cables? Is the copier placed on cables of other electrical equipment? Are the cord and cables free of damage or cracks? Has the cord or cable jacket frayed to expose the wires? Action It could result in the copier or other electrical equipment malfunctioning.
109 1. Care of the Copier Original Cover, Automatic Document Feeder Item Is the Original Pad or Document Transport Belt dirty? Is the Original Pad or Document Transport Belt scratched? Action Clean the Pad or Belt using the procedure given in "Cleaning." ➭ pp. 110, 113 Call your Technical Representative. Copy Paper Item Is the paper damp and wavy? Action ➭ p. 72 Replace the paper.
110 1. Care of the Copier Cleaning Housing Wipe the surface of the Housing clean with a soft cloth dampened with mild home detergent. 1142O082AA Original Pad 1 2 Raise the Original Cover. 1 2 Raise the Original Cover. Wipe the surface of the Original Pad clean with a soft cloth dampened with mild home detergent. 1139O1830A Chapter 8 Miscellaneous Original Glass 1142O083AA Wipe the surface of the Original Glass clean with a soft, dry cloth.
111 1. Care of the Copier Control Panel 1 2 Turn the Power Switch OFF. Wipe the surface of the control panel clean with a soft, dry cloth. NOTE 1142O084AA NEVER use a glass cleaner or any other detergent to avoid damage to the control panel keys. Front Door 1 2 Swing down the Front Door. Wipe the inside of the Front Door clean with a soft cloth.
112 1. Care of the Copier Corona Units 1 2 Open the Front Door. 3 Gently slide the Cleaning Lever back into the original position. 4 Gently slide out the Corona Unit Cleaning Lever (Lower) as far as it will go. 5 6 Gently slide the Cleaning Lever back into the original position. Gently slide out the Corona Unit Cleaning Lever (Upper) as far as it will go. 1139O1870A 1139O1880A Chapter 8 Miscellaneous 1139O1890A 1139O1900A Repeat steps 2 to 5 two to three times.
113 1. Care of the Copier Document Transport Belt 1 2 Raise the Automatic Document Feeder. 3 Hold the Document Transport Belt on both edges and pull it to the left to expose a fresh surface. 4 Wipe the fresh surface clean with a soft cloth dampened with mild home detergent. Wipe the surface of the Document Transport Belt clean with a soft cloth dampened with mild home detergent. 1139O1910A 1139O1920A Repeat these steps until the entire surface of the Belt is wiped clean.
114 2.
Inch Areas Copy Paper Zoom Ratio Original Size Size 11" × 14" 82% 11 × 17" Legal 77% 279.4 Foolscap 76% × 431.8 mm Letter 64% Invoice 50% 11" × 14" 93% 11 × 15" Legal 77% 279.4 Foolscap 77% × 381 mm Letter 73% Invoice 50% Legal 77% 11 × 14" Foolscap 77% 279.4 Letter 77% × 355.6 mm Invoice 50% Foolscap 92% Legal 8-1/2 × 14" Letter 78% 215.9 Invoice 60% × 355.6 mm 11" × 17" 121% Letter 84% Foolscap 8-1/2 × 13" Invoice 64% 215.9 11" × 17" 129% × 330.
Chapter 8 Miscellaneous 116 4. Index A Auto Size Mode p. 37 Auto Size/Manual Priority p. 57 Add Paper p. 72 Add Toner p. 70 Auto Panel Reset for Plug-In Counter p. 62 Auto Panel Reset ON/OFF p. 61 Auto Copy Start Function p. 20 Auto Dual Function p. 46 Auto Exposure Mode pp. 40, 41 Auto Reset Function p. 23 Auto Shut OFF Timing p. 63 B Book Copying p. 42 C Call-Tech.-Rep. Indicator p. 83 Cleaning p. 110 Closure Failure Indicator p. 75 Condensation p. 55 Control Panel p. 14 Copy Cycle Start p.
117 4. Index I Initial Mode p. 22 L Lightweight Original Mode pp. 30, 57 M Manual Bypass Copying p. 49 Manual Exposure Mode pp. 40, 41 Misfeed p. 76 Multi Bypass Copying p. 50 N Non-Sort Mode p. 44 Number of Copies p. 47 O Original Placement p. 28 P Paper, Add p. 72 Panel Resetting p. 22 Paper Size p. 33 PC Drum p. 55 Photo Mode pp. 40, 41 Power Switch p. 19 R Reduction Ratios p. 35 Remove Copies Indicator p. 45 Replacing the Toner Bottle p. 70 S Setting the Number of Copies p.
Chapter 8 Miscellaneous 118 4. Index T Toner, Add p. 70 Toner Replenisher Mode p. 54 Total Counter p. 52 Total Number of Copies Mode p. 52 U User’s Choice p. 56 Z Zoom Ratios p. 34 Zoom Ratio Table (Original Size to Copy Paper Size) pp.
