Z5_cvr_OM_GB_r18r.qxd 29.03.2005 15:03 Uhr Seite 2 Konica Minolta Customer Support: www.konicaminoltasupport.com Konica Minolta Photo World: www.konicaminoltaphotoworld.com Become a member of Konica Minolta Photo World today, free of charge, and enter the fascinating world of Konica Minolta photography. Register now, save 29.99 EUR, get DiMAGE Messenger for free! © 2005 Konica Minolta Photo Imaging, Inc. under the Berne Convention and the Universal Copyright Convention.
Before you begin For proper and safe use Thank you for purchasing this digital camera. Please take the time to read through this instruction manual so you can enjoy all the features of your new camera. Check the packing list before using this product. If any items are missing, immediately contact your camera dealer. Read and understand all warnings and cautions before using this product.
CAUTION • Keep batteries or small parts that could be swallowed away from infants. Contact a doctor immediately if an object is swallowed. • Store this product out of reach of children. Be careful when around children not to harm them with the product or parts. • Do not fire the flash directly into the eyes. It may damage eyesight. • Do not fire the flash at vehicle operators. It may cause a distraction or temporary blindness which may lead to an accident.
About this manual The basic operation of this camera is covered between pages 12 and 33. This section of the manual covers the camera parts, preparation of the camera for use, and the basic camera operation for recording, viewing, and deleting images. Many of the features of this camera are controlled with menus. The menu navigation sections concisely describe how to change menu settings. Descriptions of the settings immediately follow the navigation sections. Names of parts ................................
Color mode..............................................................................................................................65 Contrast...................................................................................................................................65 Sharpness ...............................................................................................................................66 Custom key function .......................................................................
Names of parts * This camera is a sophisticated optical instrument. Care should be taken to keep these surfaces clean. Please read the care and storage instructions in the back of this manual (p. 122). Accessory shoe (p. 43) Exposure-mode dial (p. 21, 29, 36 - 40) Shutter-release button Diopter-adjustment dial (p. 17) Flash (p. 26) Macro button (p. 35) Flash-mode button (p. 26) Speaker Viewfinder* (p. 17) Microphone Zoom lever (p. 20) LCD monitor* Strap eyelet (p.
GETTING UP AND RUNNING Inserting batteries Attaching the strap and lens cap This digital camera uses four AA-size alkaline or Ni-MH batteries. Do not use other types of AA batteries. The camera should be off when replacing batteries. Always keep the strap around your neck in the event that the camera is accidentally dropped. An optional leather neck strap, NS-DG1000, is also available from your Konica Minolta dealer. Availability varies with region.
Battery condition indicator This camera is equipped with an automatic battery-condition indicator. When the camera is on, the battery-condition indicator appears on the monitor. If the monitor is blank, the batteries may be exhausted or installed incorrectly. Full-battery indicator - the battery is fully charged. This indicator is displayed for three seconds on the monitor when the camera is turned on. Low-battery indicator - battery power is low. The battery should be replaced as soon as possible.
Changing the memory card Turning on the camera and displays An SD Memory Card or MultiMediaCard must be inserted for the camera to operate. If a card has not been inserted, a no-card warning is displayed on the monitor. For more about memory cards see page 124. Press the main switch to turn the camera on. Pressing the switch again turns the camera off. Always turn off the camera and confirm the access lamp is not lit before removing a memory card; damage and data loss may result. 1 2 3 4 1.
Setting the date and time Setting the Menu language After initially inserting a memory card and batteries, the camera’s clock and calendar must be set. When images are recorded, the image data is saved with the date and time of recording. 1 Set date/time? Yes No Date/Time set :move :sel. :enter Use the up and down keys to adjust the item. Press the central button to set the clock and calendar. Date/Time setup screen The date/time setup screen can be opened in section 2 of the setup menu.
BASIC RECORDING Recording images automatically Turn the exposure-mode dial to the auto-recording position (1); all camera operations are now fully automatic. The autofocus, exposure, and imaging systems will work together to bring beautiful results effortlessly. This section covers the basic operation of this camera. Thoroughly familiarize yourself with the operations in this section before moving on to the other sections in the manual.
Basic recording operation Automatic Digital Subject Program Selection The example uses auto recording. Except for movie recording, the operation for other exposure modes is the same. Automatic Digital Subject Program Selection is only available in the auto recording mode. Automatic Digital Program Selection chooses between program autoexposure and one of four digital subject programs. The digital subject programs optimize camera setting for various conditions and subjects.
Focus lock Focus signals Focus lock prevents the AF system from focusing. This can be used with off-center subjects or when a special focusing situation prevents the camera from focusing (p. 25). The focus signal in the lower right corner of the LCD monitor indicates the focus status. The shutter can be released even if the camera cannot focus on the subject. Place the subject within the focus frame. Press and hold the shutter-release button partway down.
Flash modes Flash range - auto-recording mode 1 To use the built-in flash, simply raise it (1). Lower the flash unit to prevent it from firing. Flash-mode indicator turns red while the flash is charging; wait until it becomes white before taking pictures. The camera controls the flash output automatically. For well-exposed images, the subject must be within the flash range. Distance is given from the front of the lens.
i+ button Digital subject programs Pressing the information (i ) button changes the monitor display. The display cycles among the standard display, real-time histogram, and live image only. + Standard display Real-time histogram Exposure-mode indicator Live image only The real-time histogram shows the approximate luminance distribution of the live image. This histogram cannot show the affect of flash illumination.
BASIC PLAYBACK Images can be viewed in the Quick View or playback modes. This section covers the basic operations in both modes. The playback mode has additional functions, see page 72. To view images from the playback mode, turn the mode switch to the playback position (1). The histogram shows the luminance distribution of the image from black (left) to white (right). The 256 vertical lines indicates the relative proportion of that light value in the image.
i+ button Enlarged playback The information (i+) button controls the display format. Each time the button is pressed, the display cycles through to the next format: full display, image only, index playback. In single-frame playback in Quick View or the playback mode, a still image can be enlarged for closer examination from 1.2X. The maximum magnification depends on image size ranging from 2X for 640x480 size images to 4X for 2560x1920 images.
Macro ADVANCED RECORDING Two macro modes are available: Super Macro and standard macro. Super Macro allows the camera to focus as close as 1cm (0.4 in.) from the front of the lens. When Super Macro is selected, the lens automatically zooms to a specific focallength position and cannot be changed. Standard macro allows the zoom to be used. The minimum focus distance changes with focal length, see below. This section cover the advanced recording features of this camera.
Program (P) Exposure mode The program exposure mode controls both the shutter speed and aperture to ensure correct exposures. This exposure mode allows photographers to shoot without worry about exposure settings. The shutter speed and aperture values of the exposure are displayed on the monitor when the shutter-release button is pressed partway down. If shutter speed and aperture displays turn red, the scene is beyond the exposure control range of the camera.
Manual (M) Exposure mode Manual exposure mode allows individual selection of shutter speeds and apertures. This mode overrides the exposure system giving the photographer total control over the final exposure. Use the up/down keys of the controller to change the shutter speed. NOISE REDUCTION Noise can be apparent when using a slow shutter speed or high camera sensitivity (ISO), or using the camera in hot environment. In these cases, noise-reduction is applied to the image automatically.
Movie recording Exposure compensation This camera can record digital video with sound. Total recording time varies with the image size and frame rate, see page 68. The optical and digital zoom, exposure compensation, and the macro modes can be used. Other changes can be made with the movie recording menu (p. 44). The camera exposure can be adjusted to make the final picture lighter or darker by as much as ±2Ev in 1/3 increments.
Focus area selection Attaching an accessory flash Individual focus areas can be selected when recording still images. With auto recording and Digital Subject Programs, focus area selection is reset when the camera is turned off. In P, A, S, and M exposure modes, the selected focus area remains active until reset. To extend the versatility of the camera, an accessory flash unit (sold separately) can be used.
Navigating the recording menus The recording menu displayed varies with the position of the exposure-mode dial. There are four menus depending on if auto recording, movie recording, Digital Subject Programs, or the P, A, S, and M exposure modes are selected. Pressing the menu button (1) turns the menu on and off. The four-way keys of the controller (2) move the cursor in the menu. Pressing the central button of the controller enters a setting. Activate the menu with the menu button.
Self-timer Drive modes The drive modes control the rate and method images are captured. The drive mode is set on all menus except the movie menu. With auto recording and Digital Subject Programs, the drive mode is reset to single-frame advance when the camera is turned off. In P, A, S, and M exposure modes, the drive mode remains in effect until changed. Refer to the following sections for descriptions of the drive modes.
Using the Continuous-advance modes The continuous-advance drive modes allow a series of images to be captured while holding down the shutterrelease button. These drive modes are set in section 1 of the recording menus.
Using the progressive-capture mode The Progressive-Capture drive mode continuously records images while holding down the shutter-release button. When the shutter button is released, the images stored in the camera’s buffer memory are saved. These drive mode is set in section 1 of the recording menus. Compose the picture as described in the basic recording operation section (p. 22). Press the shutter-release button partway down (1) to lock the focus and exposure for the series.
Bracketing This mode makes a three-image bracket of a scene. Bracketing is a method of taking a series of images of a static subject in which each image has a slight variation in exposure. The bracketing mode is set in section 1 of the recording menus. Immediately after selecting the bracketing option on the menu, a selection screen is displayed to select the bracketing increment.
Image size and image quality Changing image size affects the number of pixels in each image. The greater the image size, the larger the file size. Choose image size based on the final use of the image smaller images will be more suitable for web sites whereas larger sizes will produce higher quality prints. LCD monitor 2560 2048 1600 640 Number of pixels (hor. X vert.
Auto DSP Automatic Digital Subject Program Selection can be temporarily disabled in the auto-recording menu. When disabled, the program exposure mode is active. If the camera is turned off, Automatic Digital Subject Program Selection is activated. Three options are available for the Anti-Shake system in section 1 of the recording menus. Drive mode Image size Quality Auto DSP Anti-shake Single 2560x1920 Standard On Disp. + Exp. Display + Exp.
Focus modes Manual Focus This camera has autofocus and manual focus control. The focus mode is selected separately in the Digital Subject Program, movie, and P, A, S, and M exposure-mode menus. When using Digital Subject Programs, the focus mode is reset when the camera is turned off. When focusing manually, a scale shows the approximate subject distance. The scale changes depending on the focusing range.
White balance Custom White Balance White balance is the camera’s ability to make different types of lighting appear neutral. The effect is similar to selecting daylight or tungsten film, or using color compensating filters in conventional photography. An indicator will be displayed on the monitor if a setting other than auto white-balance is chosen. White balance is set independently in section 1 of the movie, and P, A, S, and M exposure-mode menus (p. 44).
Full-time AF With full-time AF active, the autofocus systems continually focuses to keep the monitor image sharp. This also reduces the autofocusing time when taking pictures. When the camera is set to manual focus, full-time AF is disabled. Turning the full-time AF function off can help conserve battery power. Full-time AF can be turned on and off in section 2 of the P, A, S, and M menus (p. 44).
Camera Sensitivity - ISO Color Mode Five camera sensitivity settings can be selected: Auto, 50, 100, 200, and 320; the numerical values are based on an ISO equivalent. ISO is the standard used to indicate film sensitivity: the higher the number, the more sensitive the film. Camera sensitivity is set in section 3 of the P, A, S, and M menus (p. 44). Sensitivity Color mode Sharpness Contrast Key func.
Sharpness Custom Key function Sharpness accents or softens details in an image in three levels: hard (+), normal, and soft (–). This can be set in section 3 of the P, A, S, and M menus (p. 44). The function assigned to the flash mode button can be selected among the flash mode, drive mode, white balance, focus mode, color mode, and camera sensitivity. This can be set in section 3 of the P, A, S, and M menus (p. 44). The flash mode can also be changed in section 2 of the P, A, S, and M menus.
Quality (MOVIE) Movies can be recorded at three size and quality combinations: 640x480 Fine, 640x480 Standard, and 320x240 Standard. Image size and quality are the same as those for still images: the larger the image size and higher the quality, the larger the file size. Quality is set in section 1 of the movie menu (p. 44). Quality Frame rate White balance Movie mode Anti-shake 640x480 STD. 15 fps Auto STD. movie Disp. + Exp.
A SHORT GUIDE TO PHOTOGRAPHY Photography can be a rewarding pursuit. It is a broad and disciplined field that can take years to master. But the pleasure in making photographs and the joy of capturing a magical moment cannot be compared. The guide is an introduction to some basic photographic principles. The lens aperture controls not only exposure, but also depth of field; the area between the closest object in focus and the furthest object in focus.
Capturing a movie frame ADVANCED PLAYBACK A single frame from a movie clip can be copied and saved as a still image. The copied image has the same image size as the original movie. The basic functions in this mode are described in the basic playback section on pages 30 through 33. This section covers how to playback movie clips as well as the advanced function on the playback menu. Movie clips can be played back in Quick View or the playback mode.
Navigating the playback menu Pressing the menu button (1) turns the menu on and off. The four-way keys of the controller (2) move the cursor in the menu. Pressing the central button of the controller enters a setting. Activate the menu with the menu button. Delete Format Lock Edit movie Copy – – – – – Slide show Playback Duration Repeat – – 5 sec. No Use the left/right keys of the controller to highlight the appropriate menu tab; the menu changes as the tabs are highlighted.
Frame-selection screen Delete When a marked-frames setting is chosen on a menu, the frame selection screen will appear. This screen allows multiple images to be chosen. The left/right keys of the controller moves the yellow border to select the image. :move :sel. :enter The up key of the controller selects the frame; when selected, an indicator appears next to the image. The down key deselects the image removing the indicator. The garbage can indicates the image is selected for deletion.
Format Lock When a memory card is formatted, all data on the card is erased. The formatting function is used to erase all data on a memory card. Before formatting a memory card, copy the data to a computer or storage device. Locking images will not protect them from being deleted when the card is formatted. Always format the memory card using the camera; never use a computer to format a card. When the format option is selected and entered in section 1 of the playback menu (p.
Movie editing Preview edit. The edit-movie option in section 1 of the playback menu allows an unwanted section to be cut from a movie clip. The movie to be edited must first be displayed in the playback mode before opening the playback menu. Highlight “Enter” in the movie edit option and press the center button of the controller to open the editing screen. Delete Format Lock Edit movie Copy – – – – – Press the center controller button to preview the edit.
Copy and E-mail Copy The copy function in section 1 of the playback menu (p. 74) makes exact copies of image or movie files and can store the copied data on another memory card. E-mail Copy in menu section 3 makes a 640x480 (VGA) JPEG copy of an original still image so that it may be easily transmitted by e-mail. E-mail copies can only be copied to the original card. Copy Delete Format Lock Edit movie Copy When the image(s) to be copied are selected, a screen with four messages is displayed.
Slide Show Section 2 of the playback menu controls the slide-show function. This function automatically displays all still images and movie clips on the memory card in order. The menu has the following options: Slide show Enter All frames Playback Marked Frames To start the slide-show presentation. Highlight “Enter” and press the central button of the controller to start the slide show. To select all the images on the memory card to be displayed in the slide-show presentation.
About DPOF This camera is supported by DPOF™ version 1.1. The DPOF (Digital Print Order Format) allows direct printing of still images from digital cameras. After the DPOF file is created, the memory card is simply taken to a photofinishing service or inserted into the memory-card slot of DPOF compatible printers. When a DPOF file is created, a misc. folder is automatically created on the memory card to store it (p. 108).
Viewing images on a television SETUP MENU It is possible to view camera images on your television. The camera has a video-out terminal to make the connection using the supplied AV cable. The camera is compatible with the NTSC and PAL standards. The video-output setting can be checked and set in section 4 of the setup menu (p. 90). The setup menu is used to control the camera’s functions and operation. The navigating the setup menu section covers the operation of the menu.
Navigating the setup menu See page 89 on how to open the menu. The four-way keys of the controller (1) move the cursor in the menu. Pressing the central button of the controller enters a setting. Use the left/right keys of the controller to highlight the appropriate menu tab; the menu changes as the tabs are highlighted. Use the up/down keys to scroll through the menu options. Highlight the option whose setting needs to be changed.
LCD Monitor Brightness Instant playback Monitor brightness can be adjusted in 11 levels. Brightness can be set individually for viewfinder and direct viewing in the recording mode. Turn the mode switch to the appropriate position before opening the brightness option in section 1 of the setup menu (p. 90). Also see page 28. An image can be displayed on the monitor after it is captured. When used with the continuous-advance, progressive-capture, or bracketing drive modes (p.
Language The language used in the menus can be changed in section 1 of the setup menu. See page 19 for details. File number (#) memory If file number memory is selected, when a new folder is created or a new memory card is used, the next image recorded will have a file number one greater than the last file saved. If the new card contains an image with a greater file number, the new image will be assigned a file number one greater than the greatest on the card.
Date imprinting Reset default The date of recording can be printed directly on the image. The imprinting function must be activated in section 2 of the setup menu (p. 90) before the image is taken. Once activated, the date will continue to be imprinted until the function is reset; a yellow bar is displayed behind the frame counter to indicate the imprinting function is active. This function affects all modes.
Playback menu Playback (Slide Show) Duration (Slide Show) Repeat (Slide Show) Date print Index print Setup menu LCD Brightness Auto-power-save period Instant playback Lens accessory File number (#) memory Folder name Date imprinting Audio signals Focus signals Shutter FX Volume Transfer mode Digital zoom Self-timer Audio signals All frames 5 seconds No Off No Normal 1 minute Off None Off Standard Off 1 1 1 2 Data storage Off 10 seconds p. p. p. p. p. 84 84 84 87 87 p. 92 p. 92 p. 93 p. 93 p. 94 p. 94 p.
Video output Camera images can be displayed on a television (p. 88). The video output can be changed between NTSC and PAL in section 4 of the setup menu. North America uses the NTSC standard and Europe uses the PAL standard. Check which standard is used in your region to play back images on your television set. Video output Transfer mode Self-timer Anti-shake NTSC Data storage 10 sec. Disp. + Exp. Zoom scale Magnification The digital zoom is operated by the zoom lever (1).
DATA-TRANSFER MODE Connecting the camera to a computer Read this section carefully before connecting the camera to a computer. Instructions on using and installing the DiMAGE Viewer software are found in the supplied software manual. The DiMAGE manuals do not cover the basic operation of computers or their operating systems; please refer to the manual supplied with your computer.
When the USB connection is completed, a drive icon, or volume, appears in My Computer or the desktop; the name varies with memory card. When using Windows XP, a window opens requesting instructions on what to do with the image data; follow the directions in the window. Connecting to Windows 98 and 98 SE The driver needs only to be installed once.
Manual Installation To install the Windows 98 driver manually, follow the instructions in the connecting-the-camera-to-a-computer section on page 103. When the camera is plugged into the computer, the operating system will detect the new device and the add-newhardware-wizard window opens. Place the DiMAGE Viewer CD-ROM in the CD-ROM drive. Click “Next.” Choose the recommended search for a suitable driver. Click “Next.” Choose to specify the location of the driver.
Memory card folder organization Once the camera is connected to the computer, image files can be accessed by double clicking on icons. Image folders are located in the DCIM folder. The misc. folder contains DPOF print files (p. 86). Drive Icon Dcim Files and folders on the memory card can be deleted using the computer. Never format the memory card from the computer; always use the camera to format the card. Only files recorded by the camera should be stored on the memory card. 10150130 PICT0001.
Disconnecting the camera Never disconnect the camera when the access lamp is red - the data or memory card may permanently be damaged. The hardware devices to be stopped will be displayed. Highlight the device by clicking on it then click “Stop.” Windows 98 / 98 Second Edition Confirm that the access lamp is not lit. Turn off the camera and then disconnect the USB cable. Windows Me, 2000 Professional, and XP A confirmation screen will appear to indicate the devices to be stopped.
Changing the memory card Never remove the card when the access lamp is red - the data or memory card may permanently be damaged. Windows 98 and 98 Second Edition 1. Turn off the camera. 2. Change the memory card. 3. Turn on the camera to remake the USB connection. Windows Me, 2000 Professional, and XP 1. Stop the USB connection using the unplug-or-eject-hardware routine (p. 110). 2. Turn off the camera. 3. Change the memory card. 4. Turn on the camera to remake the USB connection. Macintosh 1.
PictBridge Confirm the transfer-mode option in section 4 of the setup menu is set to PictBridge. Connect the camera to a PictBridge compatible printer using the camera’s USB cable. The larger plug on the cable is connected to the printer. Open the AV out/ USB port cover and insert the smaller plug of the cable into the camera. Turn the camera on; the PictBridge screen is displayed automatically. Individual still images can be selected for printing on the PictBridge screen.
The options that can be changed vary with the printer. Navigating the PictBridge menu Pressing the menu button (1) turns the menu on and off. The four-way keys of the controller (2) move the cursor in the menu. Pressing the central button of the controller enters a setting. Batch print Index print – – Activate the menu with the menu button. Use the left/right keys of the controller to highlight the appropriate menu tab; the menu changes as the tabs are highlighted.
Paper size Data print The paper size of the print can be specified. Highlight the current page size and press the central button of the controller to open paper-size screen. Use the controller to select the paper size, and press the central button to complete the operation. A paper size not available with the printer in use cannot be selected.
APPENDIX Troubleshooting The section covers minor problems with basic camera operation. For major problems or damage, or if a problem continues to reoccur frequently, contact a Konica Minolta service facility. Problem The camera will not work. Pictures are not sharp. 120 Appendix Symptom Cause Solution Access lamp turns red when pressing the main switch The batteries are dead. Replace batteries (p. 13). AA Ni-MH batteries are inserted incorrectly.
Care and storage Read this section in its entirety to get the best results from your camera. With proper care, your camera will provide years of service. Camera care • Do not subject the camera to shock or impact. • Turn off the camera when transporting. • This camera is neither waterproof nor splashproof. Inserting or removing batteries or the memory card, or operating the camera with wet hands may damage the camera. • When at the beach or near water, take care not to expose the camera to water or sand.
Memory cards Before important events and journeys SD Memory Cards and MultiMediaCards are manufactured with precision electronic components. The following may cause data loss or damage: • Improper use of the card. • Bending, dropping, or subjecting the card to impact. • Heat, moisture, and direct sunlight. • Static electrical discharge or electromagnetic fields near the card.
QuickTime system requirements IBM PC / AT Compatible Pentium processor-based PC or compatible computer Windows 98, Me, 2000, or XP. 128MB or more of RAM QuickTime is used for playing back movies. To install QuickTime, follow the instructions in the installer. QuickTime is not supplied with the camera in all sales regions. Users can download the latest version of QuickTime free of charge from the Apple Computer web site at http://www.apple.com.
Technical specifications CCD: Number of effective pixels: Total number of pixels: Camera sensitivity (ISO): Aspect ratio: Lens construction: Maximum aperture: Focal length: Focusing range: Autofocusing system: Focus modes: Shutter: Shutter speeds: Built-in flash recycling time: Monitor LCD: Monitor field of view: Viewfinder field of view: A/D conversion: Recording media: File formats: Printing output control: Menu languages: 128 Appendix 1/2.5-type interline primary-color CCD 5.0 million 5.
Index A mode, 36 AC adapter, 15 Anti-shake system, 56 Aperture priority mode, 36 Audio signals, 99 Auto power save, 14, 92, 109 Autoflash, 26 Autofocus, 58 Automatic white balance, 60 Battery Care and storage, 123 Indicator, 14 Inserting, 13 Bracketing, 52 Camera-shake warning, 27, 56 Center weighted metering, 63 Color, 65 Connecting, 102 Continuous advance, 48 Continuous AF, 58 Contrast, 65 Copy, 82 Custom key function, 67 Custom white balance, 61 Date and time, 18, 95 Date imprinting, 96 Date print (DPOF)
