E INSTRUCTION MANUAL
BEFORE YOU BEGIN Thank you for purchasing this digital camera. Please take the time to read through this instruction manual so you can enjoy all the features of your new camera. Check the packing list before using this product. If any items are missing, immediately contact your camera dealer.
FOR PROPER AND SAFE USE Read and understand all warnings and cautions before using this product. WARNING Using batteries improperly can cause them to leak harmful solutions, overheat, or explode which may damage property or cause personal injury. Do not ignore the following warnings. • Only use the batteries specified in this instruction manual. • Do not install the batteries with the polarity (+/–) reversed. • Do not use batteries which show wear or damage.
• Keep batteries or small parts that could be swallowed away from infants. Contact a doctor immediately if an object is swallowed. • Store this product out of reach of children. Be careful when around children not to harm them with the product or parts. • Do not fire the flash directly into the eyes. It may damage eyesight. • Do not fire the flash at vehicle operators. It may cause a distraction or temporary blindness which may lead to an accident.
CAUTION • Do not use or store the product in a hot or humid environment such as the glove compartment or trunk of a car. It may damage the product and batteries which may result in burns or injuries caused by heat, fire, explosion, or leaking battery fluid. • If batteries are leaking, discontinue use of the product. • The lens retracts when the camera is turned off. Touching the lens barrel while it is retracting may cause injury. • The camera temperature rises with extended periods of use.
ABOUT THIS MANUAL The basic operation of this camera is covered between pages 12 and 33. This section of the manual covers the camera parts, preparation of the camera for use, and the basic camera operation for recording, viewing, and deleting images. Many of the features of this camera are controlled with menus. The menu navigation sections concisely describe how to change menu settings. Descriptions of the settings immediately follow the navigation sections. Names of parts ................................
Viewing and rotating images ...................................................................................................31 Deleting single images ............................................................................................................31 i+ button....................................................................................................................................32 Enlarged playback ......................................................................................
Image size (Movie) ...............................................................................................................................64 Frame rate ...............................................................................................................................64 Movie file sizes ........................................................................................................................64 Movie mode .......................................................................
Data-transfer mode ..............................................................................................................................93 System requirements...............................................................................................................93 Connecting the camera to a computer ....................................................................................94 Connecting to Windows 98 and 98SE...........................................................................
NAMES OF PARTS * This camera is a sophisticated optical instrument. Care should be taken to keep these surfaces clean. Please read the care and storage instructions in the back of this manual (p. 112). Shutter-release button Flash* (p. 26) Exposure-mode dial (p. 21, 29, 36 - 40) AF window* Flash-mode button (p. 26) Card slot (p. 16) Lens* Self-timer lamp (p. 46) USB port/Video-out terminal (p. 82, 94, 104) Strap eyelet (p. 12) The battery-chamber door (p.
Diopter-adjustment dial (p. 17) Macro button (p. 35) Viewfinder* (p. 17) Zoom lever (p. 20) Controller LCD monitor* Access lamp Menu button DC terminal (p. 15) Quick View / Delete button (p. 30, 31) Information button (p.
GETTING UP AND RUNNING ATTACHING THE STRAP AND LENS CAP Always keep the strap around your neck in the event that the camera is accidentally dropped. An optional leather neck strap, NS-DG1000, is also available from your Konica Minolta dealer. Availability varies with region. Pass the end of the neck strap through the strap eyelet on the camera body (1). 1 2 Using your thumb and index finger, pinch the outside tabs of the lens cap to remove or attach.
INSERTING BATTERIES This digital camera uses four AA-size alkaline or Ni-MH batteries. Do not use other types of AA batteries. The camera should be off when replacing batteries. 3 To open the battery-chamber door, slide the lock to the open position (1). Slide the door to the front of the camera (2) to release the safety catch. Lift the door to open (3). 2 1 Insert the batteries as indicated on the diagram on the inside of the battery-chamber door.
BATTERY CONDITION INDICATOR This camera is equipped with an automatic battery-condition indicator. When the camera is on, the battery-condition indicator appears on the monitor. If the monitor is blank, the batteries may be exhausted or installed incorrectly. Full-battery indicator - the battery is fully charged. This indicator is displayed for three seconds on the monitor when the camera is turned on. Low-battery indicator - battery power is low.
CONNECTING THE OPTIONAL AC ADAPTER Always turn off the camera before changing between power supplies. The AC Adapter allows the camera to be powered from an electrical household outlet. The AC Adapter is recommended when the camera is interfaced with a computer or during periods of heavy use. AC Adapter model AC-1L is for use in North America and Japan, and AC-11 is for use in all other areas. Insert the mini plug of the AC adapter into the DC terminal (1).
CHANGING THE MEMORY CARD An SD Memory Card or MultiMediaCard must be inserted for the camera to operate. If a card has not been inserted, a no-card warning is displayed on the monitor. For more about memory cards see page 114. Always turn off the camera and confirm the access lamp is not lit before removing a memory card; damage and data loss may result. 1 2 1.Insert the memory card all the way into the card slot and release; the card should catch in the slot.
TURNING ON THE CAMERA AND DISPLAYS Press the main switch to turn the camera on. Pressing the switch again turns the camera off. Around the main switch is the mode switch. This switch is used to change between the recording and playback modes as well as the selecting the between the monitor and viewfinder display. Recording mode (Viewfinder display) - the camera can record images and the monitor is viewed through the viewfinder. The viewfinder has a built-in diopter.
SETTING THE DATE AND TIME 1 After initially inserting a memory card and batteries, the camera’s clock and calendar must be set. When images are recorded, the image data is saved with the date and time of recording. If the clock and calendar have not been set, a message is displayed for a few seconds each time the camera is turned on. This message is also displayed if the clock and calendar are reset when the camera is stored without batteries for a long period.
SETTING THE MENU LANGUAGE For customers in certain areas, the menu language may have to be set. Press the menu button (1) to open the menu; the appearance of the menu will depend on the position of the camera’s controls. 2 1 Drive m Image Quality Auto D Digital Drive mode Image size Quality Auto DSP Digital zoom Single 2048x1536 Standard On Off LCDbrightness Power save Inst.Playback Lens acc. English Language Navigating the menu is simple.
BASIC RECORDING This section covers the basic operation of this camera. Thoroughly familiarize yourself with the operations in this section before moving on to the other sections in the manual. Turn on the camera. Set the mode switch to a recording position. HANDLING THE CAMERA While using the viewfinder or LCD monitor, grip the camera firmly with your right hand while supporting the body with your left. Keep your elbows at your side and your feet shoulder-width apart to hold the camera steadily.
RECORDING IMAGES AUTOMATICALLY Turn the exposure-mode dial to the auto-recording position (1); all camera operations are now fully automatic. The autofocus, exposure, and imaging systems will work together to bring beautiful results effortlessly. 1 While many of the camera’s systems in this mode are automatic. The flash mode (p. 26) and drive mode (p. 45) can also be changed. Image size and quality can be set on the auto-recording menu (p. 44, 51-52).
BASIC RECORDING OPERATION The example uses auto recording. Except for movie recording, the operation for other exposure modes is the same. Automatic Digital Subject Program Selection is only available in the auto recording mode. Place the subject anywhere within the focus frame. Make sure the subject is within the focus range of the lens (p. 24). For very close subjects, use the macro function (p. 35). Press the shutter-release button partway down to lock the focus and exposure.
AUTOMATIC DIGITAL SUBJECT PROGRAM SELECTION Automatic Digital Program Selection chooses between program autoexposure and one of five digital subject programs. The digital subject programs optimize camera setting for various conditions and subjects. Automatic Digital Subject Program Selection is only available in auto recording and can be disabled in the auto-recording menu. For information on individual subject programs, see page 29.
FOCUS LOCK Focus lock prevents the AF system from focusing. This can be used with off-center subjects or when a special focusing situation prevents the camera from focusing (p. 25). Place the subject within the focus frame. Press and hold the shutter-release button partway down. • The focus signal indicates the focus is locked. The shutter speed and aperture value change from white to black indicating the exposure is locked.
FOCUS SIGNALS The focus signal in the lower right corner of the LCD monitor indicates the focus status. The shutter can be released even if the camera cannot focus on the subject. Focus locked. Focus confirmed (P, A, S, and M continuous AF focus mode and sports action digital subject program). Exposure continuously adjusts. Cannot focus. The subject is too close or a special situation is preventing the AF system from focusing.
FLASH MODES To change the flash mode, simply press the flash mode button (1) until the appropriate mode is indicated. 1 Autoflash - the flash fires automatically in lowlight and backlit conditions. Red-eye reduction - multiple flashes are used before the main flash burst to reduce red-eye; an effect caused by light reflected from the retina. Use in low-light conditions when taking photographs of people or animals. The preflashes contract the pupils of the subject’s eyes.
FLASH RANGE - AUTO-RECORDING MODE The camera controls the flash output automatically. For well-exposed images, the subject must be within the flash range. Distance is given from the CCD plane. Because of the optical system, the flash range is not the same at the lens’ wide-angle position as it is at the telephoto position. Wide-angle position 0.57 - 5.3m (1.87 - 17.39 ft) Telephoto position 1.57 - 5.3m (5.15 - 17.
i+ BUTTON Pressing the information (i+) button changes the monitor display. The display cycles among the standard display, real-time histogram, and live image only. Standard display Real-time histogram Live image only The real-time histogram shows the approximate luminance distribution of the live image. This histogram cannot show the affect of flash illumination. The histogram of a recorded image may not show the same distribution as the real-time histogram.
DIGITAL SUBJECT PROGRAMS Digital subject programs optimize the camera’s exposure, white-balance, and image-processing systems for specific conditions and subjects. Simply turn the exposure mode dial to select the appropriate subject program; the active subject program is displayed in the bottom left corner of the monitor Subject program indicator Portrait - optimized to reproduce warm, soft skin tones and a slight defocusing of the background.
BASIC PLAYBACK Images can be viewed in the Quick View or playback modes. This section covers the basic operations in both modes. The playback mode has additional functions, see page 68. To view images from the playback mode, turn the mode switch to the playback position (1). 1 2 To view images from the recording mode, press the Quick View / delete button (2). SINGLE-FRAME PLAYBACK AND HISTOGRAM DISPLAY Image size (p. 51) Image quality (p.
The histogram shows the luminance distribution of the image from black (left) to white (right). The 256 vertical lines indicates the relative proportion of that light value in the image. The histogram can be used to evaluate exposure, but displays no color information. VIEWING AND ROTATING IMAGES In Quick View or the playback mode, use the left/right keys of the controller to scroll through the images.
i+ BUTTON The information (i+) button controls the display format. Each time the button is pressed, the display cycles through to the next format: full display, image only, index playback. Full display Image only Index playback Information button In index playback, the four-way keys of the controller will move the yellow border. When the image is highlighted with the border, the date of recording, the lock and printing status, and the frame number of the image are displayed at the bottom of the screen.
ENLARGED PLAYBACK In single-frame playback in Quick View or the playback mode, a still image can be enlarged up to 6X in 0.2 increments for closer examination. With the image to be magnified displayed, press the right (T) side of the zoom lever to activate the enlarged playback mode. The degree of magnification is displayed on the LCD monitor. Press the right (T) side of the zoom lever to increase the image magnification. Press the left (W) side of the lever to decrease the magnification.
ADVANCED RECORDING This section cover the advanced recording features of this camera. Read the basic recording section before moving on to this section. RECORDING MODE DISPLAY A. Focus frame B. Spot metering area (p. 58) 34 ADVANCED RECORDING 1. Wide-angle converter indicator (p. 87) 2. Mode indicator 3. Flash-mode indicator (p. 26) 4. Flash-compensation display (p. 57) 5. Sharpness display (p. 61) 6. Contrast display (p. 60) 7. White-balance indicator (p. 55) 8. Camera-sensitivity (ISO) display (p.
MACRO Macro mode allows the camera to focus as close as 1 cm (0.4 in.) from the front of the lens or 8 cm (3.1 in.) from the CCD. The focus range changes with the zoom ‘s focal length, see below. Press the macro button (1) to select the macro mode. Press the macro button again to cancel the macro mode. Macro indicator 1 The following chart lists the macro ranges. All distances are measured from the CCD. Wide-angle position: 8 - 107cm (3.1 - 42.1 in.) 26.5 - 30.8mm: 107 - 237cm (42.1 - 93.3 in.
PROGRAM (P) EXPOSURE MODE The program exposure mode controls both the shutter speed and aperture to ensure correct exposures. This exposure mode allows photographers to shoot without worry about exposure settings. The shutter speed and aperture values of the exposure are displayed on the monitor when the shutter-release button is pressed partway down. If shutter speed and aperture displays turn red, the scene is beyond the exposure control range of the camera.
SHUTTER PRIORITY (S) EXPOSURE MODE The photographer selects the shutter speed and the camera sets the appropriate aperture to ensure correct exposure. When shutter priority is selected, the shutter speed on the monitor turns blue and a double arrow indicator appears next to it. The shutter speed can be set between 1/2000 and 15 seconds. If the shutter speed is beyond the aperture range, the aperture display will turn red.
MANUAL (M) EXPOSURE MODE Manual exposure mode allows individual selection of shutter speeds and apertures. This mode overrides the exposure system giving the photographer total control over the final exposure. Use the up/down keys of the controller to change the shutter speed. Use the left/right keys of the controller to change the aperture. The changes made to the exposure will be visible in the live image on the monitor.
TIME EXPOSURES Time photographs can be taken in the manual-exposure mode. Exposures up to thirty seconds can be made. The use of a tripod is recommended. The camera’s exposure system cannot be used to calculate time exposures. A separate light meter can be used to determine the exposure. 1 Use the down key of the controller to decrease the shutter speed below 15 seconds until “T” is displayed. Set the aperture using the left/right keys of the controller.
MOVIE RECORDING This camera records digital video without audio. Total recording time varies with the image size and frame rate, see page 64. Exposure compensation and the macro mode can be used. Other changes can be made with the movie recording menu (p. 44). Image size Frame rate Before recording, the frame counter shows the maximum time in seconds that can be recorded on the next movie clip. Recording time Frame the picture as described in the basic recording operation section (p. 22).
EXPOSURE COMPENSATION The camera exposure can be adjusted to make the final picture lighter or darker by as much as ±2Ev in 1/3 increments. Exposure compensation can only be used with Digital Subject Programs, the P, A, and S exposure modes, and movie recording mode. With movie recording mode, exposure compensation is reset when the camera is turned off. In Digital Subject Programs, P, A, and S exposure modes, exposure compensation remains in effect until reset.
FOCUS AREA SELECTION Individual focus areas can be selected when recording still images. With auto recording and Digital Subject Programs, focus area selection is reset when the exposure-mode dial is moved to another position or the camera is turned off. In P, A, S, and M exposure modes, the selected focus area remains active until reset. Press and hold the central button of the controller until the three spot focus areas are displayed.
NAVIGATING THE RECORDING MENUS The recording menu displayed varies with the position of the exposure-mode dial. There are four menus depending on if auto recording, movie recording, Digital Subject Programs, or the P,A,S, and M exposure modes are selected. See next page for details. Pressing the menu button (1) turns the menu on and off. The four-way keys of the controller (2) move the cursor in the menu. Pressing the central button of the controller enters a setting. Activate the menu with the menu button.
Drive mode Image size Quality Auto DSP Digital zoom Single 2048x1536 Standard On Off Drive mode Image size Quality Focus mode Digital zoom Auto-recording menu Single 2048x1536 Standard Autofocus Off Focus mode Color mode Image size Frame rate White balance Movie mode Digital Subject Program menu Cont. AF NaturalColor 320x240 15fps Auto STD. movie Movie menu Drive mode Image size Quality White balance Key func. Single 2048x1536 Standard Auto Flash mode Focus mode Full-time AF Flash mode Flash comp.
DRIVE MODES The drive modes control the rate and method images are captured. The drive mode is set on all menus except the movie menu. In auto recording mode, the drive mode is reset to single-frame advance when the exposure-mode dial is moved to another position or the camera is turned off. In Digital Subject Programs and P, A, S, and M exposure modes, the drive mode remains in effect until changed. Refer to the following sections for descriptions of the drive modes.
SELF-TIMER Used for self-portraits, the self-timer will delay the release of the shutter for approximately ten seconds or two seconds after the shutter-release button is pressed. The self-timer is set in section 1 of the recording menus (p. 44). The length of the self-timer delay is set in section 4 of the setup menu (p. 92). 1 2 With the camera on a tripod, compose the picture so the subject is within the focus frames. Press the shutter-release button partway down to lock the exposure and focus (1).
CONTINUOUS-ADVANCE MODE The continuous-advance drive mode allow a series of images to be captured while holding down the shutterrelease button. The number of images that can be captured at one time and the rate of capture depend on the image-size and image-quality settings. The maximum rate of capture is approximately 1.5 fps. This drive mode is set in section 1 of the recording menu. Drive mode Image size Quality White balance Key func.
PROGRESSIVE-CAPTURE MODE The Progressive-Capture drive mode continuously records images while holding down the shutterrelease button. When the shutter button is released, the last six images stored in the camera’s buffer memory are recorded. This drive mode is set in section 1 of the recording menu. When the red lowbattery warning is displayed, these drive modes cannot be used. Compose the picture as described in the basic recording operation section (p. 22).
BRACKETING This mode makes a three-image bracket of a scene. Bracketing is a method of taking a series of images of a static subject in which each image has a slight variation in exposure. The bracketing mode is set in section 1 of the recording menus. Immediately after selecting the bracketing option on the menu, a selection screen is displayed to select the bracketing increment. Drive mode Image size Quality White balance Key func.
Number of frames in bracketing series Frame counter The remaining number of frames in the bracket series is displayed on the monitor next to the bracketing indicator. If the memory is filled or the shutter button is released before the series has completed, the camera will reset and the entire bracket must be made again. If the red low-battery indicator appears, the bracketing drive mode is disabled. The flash cannot be used with the bracketing drive mode.
IMAGE SIZE AND IMAGE QUALITY Changing image size affects the number of pixels in each image. The greater the image size, the larger the file size. Choose image size based on the final use of the image - smaller images will be more suitable for web sites whereas larger sizes will produce higher quality prints. FINE STD. ECON. LCD monitor Number of pixels (hor. X vert.) 2048 1600 1280 640 2048 X 1536 1600 X 1200 1280 X 960 640 X 480 Fine - high-quality JPEG image. Standard - the default setting.
Approximate file sizes. 2048 X 1536 1600 X 1200 1280 X 960 640 X 480 Fine 1.3MB 770KB 550KB 170KB Standard 830KB 440KB 300KB 120KB Economy 440KB 290KB 210KB 100KB Approximate number of images that can be stored on a 16MB memory card. Fine 9 14 22 69 Standard 17 27 39 100 Economy 32 47 69 150 Camera Notes The frame counter indicates the approximate number of images that can be stored on the memory card at the camera’s image quality and size settings.
AUTO DSP Automatic Digital Subject Program Selection can be temporarily disabled in the auto-recording menu. When disabled, the program exposure mode is active. If the camera is turned off, Automatic Digital Subject Program Selection is activated. Drive mode Image size Quality Auto DSP Digital zoom Single 2048x1536 Standard On Off DIGITAL ZOOM The digital zoom is activated in the auto-recording, Digital Subject Program, and section 3 of the P, A, S, and M exposure-mode menus (p. 44).
FOCUS MODES This camera has autofocus and manual focus control. The focus mode is selected separately in the Digital Subject Program, movie, and P, A, S, and M exposure-mode menus. The selected focus mode is not reset when the camera is turned off With the P, A, S, or M exposure modes or movie recording, the autofocus mode can be specified between single-shot AF (AF-S) and continuous AF (AF-C) in section 2 of the menu (p. 44).
WHITE BALANCE White balance is the camera’s ability to make different types of lighting appear neutral. The effect is similar to selecting daylight or tungsten film, or using color compensating filters in conventional photography. An indicator will be displayed on the monitor if a setting other than auto white-balance is chosen. White balance is set independently in section 1 of the movie, and P, A, S, and M exposure-mode menus (p. 44).
Custom White Balance Custom white-balance allows the camera to be calibrated to a specific lighting condition. The setting can be used repeatedly until reset. Custom white balance is especially useful with mixed-lighting or when critical control over color is needed. The object used to make a calibration must be neutral. A blank piece of white paper is an ideal surface and can easily be carried in a camera bag. To calibrate the camera, select custom setup (Cust.
FULL-TIME AF With full-time AF active, the autofocus systems continually focuses to keep the monitor image sharp. This also reduces the autofocusing time when taking pictures. When the camera is set to manual focus, full-time AF is disabled. Turning the full-time AF function off can help conserve battery power. Full-time AF can be turned on and off in section 2 of the P, A, S, and M menus (p. 44). FLASH MODE The flash modes can be changed in section 2 of the P, A, S, and M menus (p. 44).
Flash compensation changes the ratio between the ambient and flash exposures. When using fill-flash to reduce harsh shadows caused by direct sunlight, flash compensation changes the ratio between the highlights and shadows. The flash affects the darkness of the shadows without affecting the area illuminated by the sun. By decreasing the flash output with a negative Ev setting, the shadows receive less light and are deeper, but retain detail that would be lost without the flash.
CAMERA SENSITIVITY - ISO Five camera sensitivity settings can be selected: Auto, 64, 100, 200, and 400; the numerical values are based on an ISO equivalent. ISO is the standard used to indicate film sensitivity: the higher the number, the more sensitive the film. Camera sensitivity is set in section 3 of the P, A, S, and M menus (p. 44).
COLOR MODE The color mode controls whether a still image is color or black and white. This must be set before the image is recorded. The color mode is set in section 3 of the P, A, S, and M menus and section 2 of the movie menu (p. 44). The live image reflects the selected color mode. The color mode has no effect on image file size. Vivid color Black & White Sepia Natural Color reproduces the colors in the scene faithfully. This mode uses no monitor indicator when active.
SHARPNESS Sharpness accents or softens details in an image in three levels: hard (+), normal, and soft (–). This can be set in section 3 of the P, A, S, and M menus (p. 44). Any changes made are applied to the live image, but may be difficult to see. However, when viewed with a computer, the changes will be evident. If any level except normal is selected, an indicator appears on the monitor as a warning.
CUSTOM KEY FUNCTION The function assigned to the flash-mode button can be selected among the flash mode, drive mode, white balance, focus mode, color mode, and sensitivity. This can be set in section 1 of the P, A, S, and M menus (p. 44). The flash mode can also be changed in section 2 of the P, A, S, and M menus. Drive mode Image size Quality White balance Key func. After selecting the custom key function option on the menu, press the central button of the controller to display the selection screen.
When selecting the bracketing drive mode, or preset white balance, a selection screen appears. Use the left/right keys of the controller to display the bracketing increment or preset white balance, and press the central button of the controller to select it. :select :enter When selecting custom white balance, the calibration screen appears. Fill the frame with a white object and press the central button of the controller to calibrate the camera.
IMAGE SIZE (MOVIE) Movies can be recorded at two sizes: 640x480 and 320x240. The larger the image size, the higher the image quality and the larger the file sizes. Image size is set in section 1 of the movie menu (p. 44). Image size Frame rate White balance Movie mode 320x240 15ps Auto STD. movie FRAME RATE Movies can be recorded at two frame rates: 15 fps and 30 fps. 640x480 size image can only be recorded at 15fps. The higher the frame rate, the smoother the moving image and the larger the file sizes.
The writing speed of the memory card may prematurely end the recording of a movie clip. Test the card before important events. Check the Konica Minolta web site for the latest compatibility information: North America: http://www.konicaminolta.us/ Europe: http://www.konicaminoltasupport.com. MOVIE MODE The movie mode option selects the type of movie recorded. Standard produces a normal movie clip.
A SHORT GUIDE TO PHOTOGRAPHY Photography can be a rewarding pursuit. It is a broad and disciplined field that can take years to master. But the pleasure in making photographs and the joy of capturing a magical moment cannot be compared. The guide is an introduction to some basic photographic principles. The lens aperture controls not only exposure, but also depth of field; the area between the closest object in focus and the furthest object in focus.
The shutter controls not only exposure, but also the ability to stop motion. Fast shutter speeds are used in sport photography to stop action. Slow shutter speeds can be used to show the flow of motion such as water cascading over a waterfall. The use of a tripod is recommended with slow shutter speeds. The change in aperture and shutter speed is not apparent in the live image. Unlike film cameras, test photographs can be taken and immediately viewed.
ADVANCED PLAYBACK The basic functions in this mode are described in the basic playback section on pages 30 through 33. This section covers how to playback movie clips as well as the advanced function on the playback menu. Movie clips can be played back in Quick View. PLAYING BACK MOVIES Play Use the left/right keys of the controller to display the movie. Press the center of the controller to play back the movie clip.
CAPTURING A MOVIE FRAME A single frame from a movie clip can be copied and saved as a still image. The copied image has the same image size as the original movie. During playback, press the center button of the controller to pause the movie playback at the point to capture the frame. When the movie is paused, the left/right keys can be used to jog the clip to display the correct frame. Pause Rew Fwd Press the up key of the controller to capture the frame.
NAVIGATING THE PLAYBACK MENU Pressing the menu button (1) turns the menu on and off. The four-way keys of the controller (2) move the cursor in the menu. Pressing the central button of the controller enters a setting. Activate the menu with the menu button. Use the left/right keys of the controller to highlight the appropriate menu tab; the menu changes as the tabs are highlighted. Use the up/down keys to scroll through the menu options. Highlight the option whose setting needs to be changed.
Delete Format Lock Copy – – – – Slide show Playback Duration Repeat – – 5 sec. No DPOF set Date print Index print E-mail copy – Off – – To delete images on the memory card (p. 73). To format the memory card (p. 74). To protect images from deletion (p. 75). To copy images from one memory card to another (p. 76). To play back images automatically (p. 78) To select the images for the Slide Show (p. 78). To specify how long each image is played back (p.
FRAME-SELECTION SCREEN When a marked-frames setting is chosen on a menu, the frame selection screen will appear. This screen allows multiple images to be chosen. The left/right keys of the controller moves the yellow border to select the image. :move :sel. :enter The up key of the controller selects the frame; when selected, an indicator appears next to the image. The down key deselects the image removing the indicator. The garbage can indicates the image is selected for deletion.
DELETE Deleting permanently erases the file. Once deleted, a file cannot be recovered. Care should be taken when deleting images. Single, multiple, or all files on the memory card can be deleted in section 1 of the playback menu (p. 71). The delete option has three settings: Delete Format Lock Copy – – – – This frame The file displayed or highlighted in the playback mode is deleted. All frames All unlocked files are deleted. Marked frames To delete multiple files.
FORMAT When a memory card is formatted, all data on the card is erased. The formatting function is used to erase all data on a memory card. Before formatting a memory card, copy the data to a computer or storage device. Locking images will not protect them from being deleted when the card is formatted. Always format the memory card using the camera; never use a computer to format a card. When the format option is selected and entered in section 1 of the playback menu (p. 71), a confirmation screen appears.
LOCK Single, multiple, or all files can be locked. A locked file cannot be deleted by either the playback menu functions or the QV/delete button. However, the formatting function (p. 74) will erase all files on a memory card whether locked or not. Important images should be locked. The lock function is in section 1 of the playback menu (p. 71). The lock option has four settings: This frame The file displayed or highlighted in the playback mode is locked.
COPY AND E-MAIL COPY The copy function in section 1 of the playback menu (p. 71) makes exact copies of image or movie files and can store the copied data on another memory card. E-mail Copy in menu section 3 makes a standard 640 X 480 (VGA) JPEG copy of an original still image so that it may be easily transmitted by e-mail. E-mail copies can only be copied to the original card.
Copy When the image(s) to be copied are selected, a screen with four messages is displayed. The messages are highlighted during the copying procedure. Copy Copying to camera memory. Change card. Copying to card. Copying completed. Enter Copied to 101KM_CP. OK When the change-card message is highlighted, remove the camera’s memory card and insert the card to which the image should be copied. Press the central button of the controller to continue or the menu button to cancel the copy operation.
SLIDE SHOW Section 2 of the playback menu controls the slide-show function. This function automatically displays all still images and movie clips on the memory card in order. The menu has the following options: Enter To start the slide-show presentation. Highlight “Enter” and press the central button of the controller to start the slide show. All frames To select all the images on the memory card to be displayed in the slide-show presentation.
The controller can be used to control the presentation during playback. Press the central button of the controller to pause and restart the slide show presentation. Slide show Playback Duration Repeat – – 5 sec. No The left/right keys advance to the next still image or return to the previous one. During a movie, the keys forward or rewind the clip Press the menu button to cancel the presentation. Camera Notes The presentation can be viewed without image information.
ABOUT DPOF This camera is supported by DPOF™ version 1.1. The DPOF (Digital Print Order Format) allows direct printing of still images from digital cameras. After the DPOF file is created, the memory card is simply taken to a photofinishing service or inserted into the memorycard slot of DPOF compatible printers. When a DPOF file is created, a misc. folder is automatically created on the memory card to store it (p. 98).
When the this-frame or all-frames setting is chosen, a screen appears requesting the number of copies of each image; a maximum of nine copies can be ordered. Use the up/down keys of the controller to set the required number of copies. If the all-frames setting was used to create a print order, any additional images recorded afterwards will not be included in the order. DPOF files created with another camera will be canceled.
VIEWING IMAGES ON A TELEVISION It is possible to view camera images on your television. The camera has a video-out terminal to make the connection using the supplied Video cable VC-400. The camera is compatible with the NTSC and PAL standards. The video-output setting can be checked and set in section 4 of the setup menu (p. 92). 1.Turn off the television and the camera. 2.Insert the small plug of the video cable into the camera’s video-out terminal.
SETUP MENU The setup menu is used to control the camera’s functions and operation. The navigating the setup menu section covers the operation of the menu. The section is followed by detailed descriptions of the settings. OPENING THE SETUP MENU The setup menu is opened from the other menus. It can be accessed from any of the recording or playback menus.
NAVIGATING THE SETUP MENU See page 83 on how to open the menu. The four-way keys of the controller (1) move the cursor in the menu. Pressing the central button of the controller enters a setting. Use the left/right keys of the controller to highlight the appropriate menu tab; the menu changes as the tabs are highlighted. Use the up/down keys to scroll through the menu options. Highlight the option whose setting needs to be changed.
LCDbrightness Power save Inst.Playback Lens acc. Language – 1 min. Off None English File # memory Folder name Noise reductn Date/Time set Date imprint Off Std. form On – Off Reset default Audio signals Focus signal Shutter FX – 1 1 1 Video output Transfer mode Self-timer NTSC Data storage 10 sec. To set monitor brightness (p. 86). To set the auto power save period (p. 86). To play back a still image after it is recorded (p. 86). Specified when using a lens accessory (p. 87).
LCD MONITOR BRIGHTNESS Monitor brightness can be adjusted in 11 levels. Brightness can be set individually for viewfinder and direct viewing in the recording mode. Turn the mode switch to the appropriate position before opening the brightness option in section 1 of the setup menu (p. 85). Also see page 28. Use the left/right keys of the controller to adjust brightness, the monitor image changes accordingly. Press the central button of the controller to set the level.
LENS ACCESSORY This camera is compatible with the optional Wide-angle Converter ZCW-200. This 0.7X wide-angle converter reduces the focal length of the zoom lens’ wide-angle position giving it the equivalent of a 26mm lens on a 35mm camera. When the converter is mounted, the lens accessory option in section 1 of the setup menu should be set to “WideConvertr.” An indicator (W W ) appears in the top left corner of the monitor as a warning. The optical zoom is automatically set to the wide-angle position.
FOLDER NAME All recorded images are stored in folders on the memory card. Two foldername formats are available in section 2 of the setup menu, standard and date. Standard folders have an eight character name. The initial folder is named 100KM008. The first three digits are the folder’s serial number, which will increase by one each time a new folder is created. The next two letters refer to Konica Minolta, and the last three numbers indicate the camera used; 008 indicates a DiMAGE Z10.
DATE AND TIME SETUP It is important to accurately set the clock. When a still image or a movie clip is recorded, the date and time of the recording are saved with the image and are displayed during playback or can be read with the supplied DiMAGE Viewer software. The date format that is displayed or imprinted can be changed: YYYY/MM/DD (year, month, day), MM/DD/YYYY (month, day, year), DD/MM/YYYY (day, month, year). See page 18 for instructions on how to set the clock and calendar.
RESET DEFAULT This function affects all modes. When selected, a confirmation screen appears; choosing “Yes” resets the following functions and settings, “No” cancels the operation.
Playback menu Playback (Slide Show) Duration (Slide Show) Repeat (Slide Show) Date print Index print All frames 5 seconds No Off No p. p. p. p. p. 78 78 78 81 81 Setup menu LCD brightness Auto-power-save period Instant playback Lens accessory File number (#) memory Folder name Noise reduction Date imprinting Audio signals Focus signals Shutter FX Transfer mode Self-timer Normal 1 minute Off None Off Standard On Off 1 1 1 Data storage 10 sec. p. p. p. p. p. p. p. p. p. p. p. p. p.
FOCUS SIGNAL When the shutter-release button is pressed partway down, an audio signal confirms the AF system has focused. The focus signals can be changed or turned off in section 3 of the setup menu (p. 85). Two tones are available. SHUTTER FX When the shutter is released, a shutter sound effect gives a positive confirmation a still image is recorded. The sound effect can be turn off in section 3 of the setup menu (p. 85). Two shutter effects are available.
DATA-TRANSFER MODE Read this section carefully before connecting the camera to a computer. Instructions on using and installing the DiMAGE Viewer software are found in the supplied software manual. The DiMAGE manuals do not cover the basic operation of computers or their operating systems; please refer to the manual supplied with your computer.
CONNECTING THE CAMERA TO A COMPUTER Confirm the battery has sufficient power before connecting the camera to a computer; the full-battery indicator should be displayed on the monitor. The use of the AC adapter (sold separately) is recommended over the use of the battery. For users with Windows 98 or 98 Second Edition, read the section on page 95 on how to install the necessary USB driver before connecting the camera to a computer. 1.Start up the computer.
When the USB connection is completed, a drive icon, or volume, appears in My Computer or the desktop; the name varies with memory card. When using Windows®XP or Mac OS X, a window opens requesting instructions on what to do with the image data; follow the directions in the window. Mac OS X Mac OS Windows XP Windows CONNECTING TO WINDOWS 98 AND 98 SE The driver needs only to be installed once.
Manual Installation To install the Windows®98 driver manually, follow the instructions in the connecting-the-camera-to-acomputer section on page 94. When the camera is plugged into the computer, the operating system will detect the new device and the add-new-hardware-wizard window opens. Place the DiMAGE Viewer CD-ROM in the CD-ROM drive. Click “Next.” Choose the recommended search for a suitable driver. Click “Next.” Choose to specify the location of the driver.
The add new hardware wizard will confirm the location of the driver. The letter designating the CDROM drive will vary between computers. Click “Next” to install the driver in the system. One of three drivers may be located: MNLVENUM.inf, USBPDR.inf, or USBSTRG.inf. The last window confirms the driver has been installed. Click “Finish” to close the add new hardware wizard. Restart the computer. When the my-computer window is opened, a new removable-disk icon is displayed.
MEMORY CARD FOLDER ORGANIZATION Drive Icon Dcim Misc Once the camera is connected to the computer, image files can be accessed by double clicking on icons. Image folders are located in the DCIM folder. The misc. folder contains DPOF print files (p. 80). Files and folders on the memory card can be deleted using the computer. Never format the memory card from the computer; always use the camera to format the card. Only files recorded by the camera should be stored on the memory card.
The number in the image file name may not correspond to the frame number of the image. As images are deleted in the camera, the frame counter will adjust itself to show the number of images on the card and reassign the frame numbers accordingly. The serial numbers used with image files will not change when an image is deleted. When a new image is recorded, it will be assigned a number one greater than the largest serial number in the folder.
DISCONNECTING THE CAMERA Never disconnect the camera when the access lamp is red - the data or memory card may permanently be damaged. Windows 98 / 98 Second Edition Confirm that the access lamp is not lit. Turn off the camera and then disconnect the USB cable. Windows Me, 2000 Professional, and XP To disconnect the camera, click once on the unplug-or-eject-hardware icon located on the task bar. A small window will open indicating the device to be stopped. Click on the small window to stop the device.
The hardware devices to be stopped will be displayed. Highlight the device by clicking on it then click “Stop.” A confirmation screen will appear to indicate the devices to be stopped. Clicking “OK” will stop the device. A third and final screen will appear to indicate the camera can be safely disconnected from the computer. Close the window, turn the camera off, and then disconnect the USB cable.
CHANGING THE MEMORY CARD Never remove the card when the access lamp is red - the data or memory card may permanently be damaged. Windows®98 and 98 Second Edition 1. Turn off the camera. 2. Change the memory card. 3. Turn on the camera to remake the USB connection. Windows®Me, 2000 Professional, and XP 1. Stop the USB connection using the unplug-or-eject-hardware routine (p. 100). 2. Turn off the camera. 3. Change the memory card. 4. Turn on the camera to remake the USB connection. Mac OS 1.
UNINSTALLING THE DRIVER SOFTWARE - WINDOWS 1.Insert a memory card in the camera and connect it to the computer with the USB cable. Other devices must not be connected to the computer during this procedure. 2.Right click on the My-computer icon. Select “properties” from the drop-down menu. Windows®XP: from the start menu go to the control panel. Click on the performance and maintenance category. Click “System” to open the system properties window. 3.
PictBridge Confirm the transfer-mode option in section 4 of the setup menu is set to PictBridge. Connect the camera to a PictBridge compatible printer using the camera’s USB cable. The larger plug on the cable is connected to the printer. Open the USB port/Video-out terminal cover and insert the smaller plug of the cable into the camera. Turn the camera on; the PictBridge screen is displayed automatically. Individual still images can be selected for printing on the PictBridge screen.
No. of prints: Print size: Layout: Print quality: Data print: :start 7 Printer setup Printer setup Printer setup Printer setup The number of prints in the print run are displayed as well as the print parameters selected with the menu. See the menu navigation section for more information (p. 106). Press the central button of the controller to begin printing, or press the menu button to return to the PictBridge screen.
NAVIGATING THE PictBridge MENU Pressing the menu button (1) turns the menu on and off. The four-way keys of the controller (2) move the cursor in the menu. Pressing the central button of the controller enters a setting. Activate the menu with the menu button. Use the left/right keys of the controller to highlight the appropriate menu tab; the menu changes as the tabs are highlighted. Use the up/down keys to scroll through the menu options. Highlight the option whose setting needs to be changed.
Batch print Index print – – Index to menu functions Batch print, 107 Index print, 107 Paper size Layout Print quality Data print Printer setup Printer setup Printer setup Printer setup Paper size, 108 Layout, 108 Print quality, 109 Data print, 109 DPOF print – DPOF print, 109 Batch print Batch print in section 1 selects all still images on the memory card for printing. Two options are available: All-frames - to print all images on the card.
Paper size Paper size Layout Print quality Data print Printer setup L Postcard 2L A4 Printer setup The paper size of the print can be specified in section 2 of the PictBridge menu. The printer-setup option uses the size set with the printer. Highlight the current size setting in the menu and press the central button of the controller to open the paper-size screen. 2” X 3” card 100mmX150mm 4” X 6” 8” X 10” Letter Use the four-way key of the controller to highlight the new paper size.
Print quality The print quality can be set in section 2 of the PictBridge menu. The printer-setup option uses the quality set with the printer. The fine quality can be specified with the camera. Data print Data can be printed with the image. The printer-setup option uses the options set with the printer. The date of capture and the file name can be selected for printing. Data printing can also be disabled with the menu.
APPENDIX TROUBLESHOOTING The section covers minor problems with basic camera operation. For major problems or damage, or if a problem continues to reoccur frequently, contact a Konica Minolta service facility. Problem Symptom Cause The batteries are dead. This camera will not work. APPENDIX Replace batteries (p. 13) AA Ni-MH batteries are inserted incorrectly.
Focus signal is red. Pictures are not sharp. Pictures are taken indoors or in low-light situations without flash. While using flash, the pictures are too dark. Subject is too close. Make sure the subject is within the autofocus range (p. 24) or use the macro mode (p. 35). The camera is in macro mode. Cancel the macro mode setting (p. 35). A special situation is preventing the autofocus system from focusing (p. 25).
CARE AND STORAGE Read this section in its entirety to get the best results from your camera. With proper care, your camera will provide years of service. Camera care • Do not subject the camera to shock or impact. • Turn off the camera when transporting. • This camera is neither waterproof nor splashproof. Inserting or removing batteries or the memory card, or operating the camera with wet hands may damage the camera. • When at the beach or near water, take care not to expose the camera to water or sand.
LCD monitor care • The LCD monitor is manufactured using high-precision technology and more than 99.99% of the pixels operate properly. Less than 0.01% of the monitor pixels are displayed as color or bright points; this is not monitor defect and does not affect the recorded image. • Do not apply pressure to the surface of the LCD monitor; it may be permanently damaged. • In cold temperatures, the LCD monitor may become temporarily dark. When the camera warms up, the display will function normally.
Memory cards SD Memory Cards and MultiMediaCards are manufactured with precision electronic components. The following may cause data loss or damage: • Improper use of the card. • Bending, dropping, or subjecting the card to impact. • Heat, moisture, and direct sunlight. • Static electrical discharge or electromagnetic fields near the card. • Removing the card or interrupting the power supply while the camera or a computer is accessing the card (reading, writing, formatting, etc.).
Before important events and journeys • Check the camera’s operation; take test pictures and purchase spare batteries. • Konica Minolta has no responsibility for any damage or loss incurred by equipment malfunction. Copyright • TV program, films, video tapes, photographs, and other materials may be copyrighted. Unauthorized recording or duplication of such material may be contrary to copyright laws. Taking pictures or images of performances, exhibitions, etc.
QUICKTIME SYSTEM REQUIREMENTS IBM PC / AT Compatible Pentium processor-based PC or compatible computer ® Windows®98, Me, 2000, or XP 128MB or more of RAM 116 APPENDIX To install QuickTime™, follow the instructions in the installer. Macintosh users can download the latest version of QuickTime™ free of charge from the Apple Computer web site: http://www.apple.com.
This mark on your camera certifies that this camera meets the requirements of the EU (European Union) concerning interference causing equipment regulations. CE stands for Conformité Européenne (European Conformity). FCC Compliance Statement Declaration on Conformity Responsible Party: Konica Minolta Photo Imaging U.S.A. Inc.
TECHNICAL SPECIFICATIONS CCD: Number of effective pixels: Total number of pixels: Camera sensitivity (ISO): Aspect ratio: Lens construction: Maximum aperture: Focal length: Focusing range (from the CCD): Autofocusing system: Focus modes: Shutter: Shutter speeds: Built-in flash recycling time: Monitor LCD: Monitor field of view: Viewfinder field of view: A/D conversion: Recording media: File formats: Printing output control: Menu languages: Video output: 118 APPENDIX 1/2.
Batteries: Four AA alkaline or Ni-MH batteries. Battery performance (recording): Approximately 500 frames based on the CIPA standard with alkaline batteries, LCD monitor on, full-size images (2048x1536), standard image quality, no instant playback, no full-time AF, flash used with 50% of the frames. Approx. 240 minutes for continuous movie recording with alkaline batteries Battery performance (playback): Approx.
© 2004 Konica Minolta Photo Imaging, Inc. under the Berne Convention and the Universal Copyright Convention.
