Di620PE CF911PE Operator’s Manual
i Using the Printer Properly To ensure optimum performance of the printer, follow the precautions listed below. • Never place a heavy object on the printer. • Never subject the printer to shocks. • Never open any doors or turn the printer off while the printer is making prints. • Never bring any magnetized object near the printer. • Never use flammable sprays, liquids or gases near the printer. • Never modify the printer, as a fire or electrical shock could result.
ii Using the Printer Properly • Always use the correct power voltage, as improper voltage can cause a fire or electrical shock. • Never use a multiple outlet adapter, as a fire or electrical shock can result. • Should the power cord become damaged, immediately turn the printer off, unplug the power cord and call your technical representative. A damaged cord can result in a fire or cause an electric shock.
iii Safety Precautions Safety Information This is a digital printer which prints by means of a laser. There is no possibility of danger from the laser, provided the printer is operated according to the instructions in this manual. Since radiation emitted by the laser is completely confined within protective housing, the laser beam cannot escape from the machine during any phase of user operation. This printer is certified as a Class 1 laser product.
iv Safety Precautions For European Users: WARNING: Use of controls, adjustments or performance of procedures other than those specified in this manual may result in hazardous radiation exposure. This is a semiconductor laser. The maximum power of the laser diode is 15mW and the wavelength is 780nm. (Two provided.) For Denmark Users: ADVARSEL Usynlig laserstråling ved åbning, når sikkerhedsafbrydere er ude af funktion. Undgå udsættelse for stråling.
v Safety Precautions Laser Safety Label A laser safety label is attached to the outside of the printer as shown below. For Europe For United States 1155O698CB 4115O003AA 1155O699EB The Manufacturer’s Name Plate is affixed at the position illustrated above. Please write down the Model Name and Serial No. of your printer here. Model: Serial No.
vi Regulatory Information For United States Users: WARNING This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
vii Regulatory Information For European Users: Thank you for choosing Minolta. This operator's manual explains how to operate the printer and replenish its supplies. It also gives some troubleshooting tips as well as general precautions to be observed when operating the printer. To ensure the best performance and effective use of your printer, read this manual carefully until you familiarize yourself thoroughly with its operation and features.
viii Technical Support For United States and Canada Users: Thank you for choosing Minolta quality. For over 30 years Minolta has been a leader on the forefront of office equipment technology and service. Our desire has always been to bring you highly reliable products. We pledge to continue to provide you, our customer, with our state of the art equipment, as well as full customer service for all our products. We look forward to a long healthy relationship with you and our company.
ix Terms and Symbols for the Type of document and Paper A few special terms and symbols are used in this manual to designate types of paper. This page explains about these terms and symbols. Feeding Direction (paper path) In this printer system, paper is taken up from the right-hand side of the printer and fed through the printer toward the left-hand side, face up onto the Tray. In the figure below, the direction in which the paper is fed, as indicated by the arrow, is called the “feeding direction.
x Contents Using the Printer Properly .................................................................................. i Safety Precautions .............................................................................................iii Regulatory Information ..................................................................................... vi Technical Support ...........................................................................................
xi Contents Misfeed Clearing Procedures ....................................................................... 4-14 5. When a Staple Misfeed Occurs Clearing the Staple Misfeed ......................................................................... 4-30 6. What Does Each Message Mean? What does each message mean? ................................................................... 4-32 Chapter 5 Troubleshooting 1. When This Type of Print is Produced When this type of print is produced ...................
Safety Notes Chapter 1 1-1 Chapter 1 Safety Notes Di620PE Operator’s Manual
1-2 Safety Notes Chapter 1 1. Installing the Printer Installation Site To ensure utmost safety and prevent possible malfunction of the printer, install it in a location which meets the following requirements. ◆ A place away from a curtain or the like that may catch fire and burn easily. ◆ An area where there is no possibility of being splashed with water or other types of liquid. ◆ An area free from direct sunlight. ◆ A place out of the direct air stream of an air conditioner, heater, or ventilator.
1-3 The operating environmental requirements of the printer are as follows: Temperature : 10°C to 32°C (50°F to 90°F) with a fluctuation of 10°C (18°F) per hour. Humidity : 15% to 85% with a fluctuation of 10% per hour. Using the Printer Properly To ensure optimum performance of the printer, follow the precautions listed below. ◆ NEVER place a heavy object on the printer or subject the printer to shocks. ◆ NEVER open any doors, or turn OFF the printer while the printer is making prints.
1-4 Safety Notes Chapter 1 2. Precautions for Use Note on Making Multiple Prints If the fusing temperature drops excessively during a multi-print cycle, there is a possibility that the printing speed will be reduced. The printing speed will automatically return to normal when the fusing temperature rises enough to ensure good fusing performance.
Chapter 2 Getting to Know Your Printer Di620PE Operator’s Manual Getting to Know Your Printer Chapter 2 2-1
2-2 1. System Overview System Overview Getting to Know Your Printer Chapter 2 The following overview presents the printer and the available options with a brief explanation of the function of each. Refer to the separate manual “Print Station Manager Reference Manual”. 1155O014AA Finisher FN-3
2-3 2. Printer Parts and Accessories 2 5 4 6 7 8 3 9 4115O006AA Printer 1 Exit Tray Extender : Slide this extender out when making prints on large-size paper. 2 Exit Tray : Holds prints fed out of the printer. (Option) 3 Front Door : Open to clear a paper misfeed. ☞p. 4-12 Closing the Front Door after a misfeed has been cleared will turn the misfeed warning message on the control panel OFF. 4 Upper Front Door : Open to replace the Toner Bottle. ☞p.
2-4 Getting to Know Your Printer Chapter 2 2. Printer Parts and Accessories 10 13 11 12 4115O007AB Drawers of the Printer 10 Tray 1 : Holds up to 550 sheets of paper. ☞p. 4-2 11 Tray 2 : Holds up to 550 sheets of paper. ☞p. 4-3 It can accommodate paper of different sizes. 12 Tray 3 : Holds up to 2,700 sheets of paper. ☞p. 4-4 13 Paper Descent Key : Press before sliding the drawer out of the printer.
2-5 2.
2-6 2. Printer Parts and Accessories Getting to Know Your Printer Chapter 2 Finisher FN-3 1 Manual Staple Tray Cover 2 Top Offset Tray 3 Grip 7 Finisher Door 8 Bottom Offset Tray : Open to load documents for manual stapling or to clear a paper misfeed. : Receives sorted print sets or grouped print stacks. : Grasp and press here to slide the Finisher away from the printer to clear a misfeed or other service job. : Open to replace the Staple Cartridge. ☞p. 4-8 Open to clear a paper misfeed. ☞p.
2-7 2. Printer Parts and Accessories 2 1 8 3 M5 M4 M1 4 5 M7 M3 D2 7 D1 6 4115O009AB 1 Toner Bottle : Contains Toner. Replace it with a new one when the warning message tells you to. ☞p. 4-6 2 Toner Bottle Holder : Swing open to replace the Toner Bottle. ☞p. 4-6 3 Misfeed Removal Guide Unit M5 : Use to clear a misfed sheet of paper. ☞p. 4-14 4 Misfeed Removal Lever M4 : Press down to pull out the M5 Unit. ☞p. 4-14 5 Misfeed Removal Knob M3 : Use to clear a misfed sheet of paper. ☞p.
2-8 3. Turning ON and OFF Turning ON and OFF • Turning the Printer ON: Press the Power Switch to the Getting to Know Your Printer Chapter 2 • Turning the Printer OFF: Press the Power Switch to the position. (ON) position. (OFF) 4115O050AB When the unit is turned ON The printer icon on the print station manager screen changes as follows when the power is turned ON.
2-9 3. Turning ON and OFF Panel Indicator Green Red 4115O057AA Indicator Meaning Power Indicator ON: Print engine is in the ready state. Blinking: warming up. Slow Blinking: Power save mode. Error Indicator ON: Printing error, fatal error, paper misfeed, something that prevents printing has occured. Blinking: Maintenance call.
2-10 Getting to Know Your Printer Chapter 2 3.
Chapter 3 Printing Procedure Di620PE Operator’s Manual Printing Procedure Chapter 3 3-1
3-2 1. Printing & Function Settings Printing & Function Settings Refer to the following manuals for the procedure about printing and/or function settings.
3-3 2. Basic Printing Overview Manual Feed Tray • Use the Manual Feed to make prints on paper not loaded in any tray, or to print onto OHP transparencies, thick paper, or any other special paper. • When using the Manual Feed Tray, you can load multiple sheets of paper. • The setting of paper size is needed for manual feed printing. • Manual Feed cannot be used for a reserved job.
3-4 3. Selecting the Finishing In the following, we explain about different finishing functions and setting procedures. For more infomation on finishing function settings and options, please refer to the PrintStation Manager Reference Manual. Staple Printing Procedure Chapter 3 • This function is effective when making multiple printings of a multipage document. Prints are sorted or grouped into complete sets of the jobs and then stapled.
3-5 3. Selecting the Finishing Selecting the Finishing Function Sort/Group NOTES • When the Finisher FN-102 is installed, prints are fed out in a sawtooth manner in Sort or Group mode. • When the Finisher FN-3 is installed, sorted sets and grouped stacks are separated by a separator page. • When a Finisher is not installed, sorted sets and grouped stacks are separated by a separator page.
3-6 3. Selecting the Finishing Hole Punch Printing Procedure Chapter 3 1 Select the desired finishing function. Refer to the printer driver manual (PrintStation Manager Reference Manual) for a detailed description of the setting procedures and setting items. NOTES • The size of the paper for Hole Punch is 11″×17″L, LegalL, LetterL, LetterC, A3L, A4L and A4C only. • Hole Punch is not possible in the Interrupt mode.
3-7 3. Selecting the Finishing Staple 4115O054CA * When you touch a stapling key, the finisher is automatically set into the Sort mode. Useful Tip Paper size: A3L to A4, 11″×17L″ to Letter Number of sheets: 2 to 50 Kinds of Paper: Plain paper, Recycled paper Di620PE Operator’s Manual Printing Procedure Chapter 3 You have a choice of the following two stapling types.
3-8 3. Selecting the Finishing Manual Staple Open the Manual Staple Tray Cover. Chapter 3 1 4 1155O033AA 1155O034AA Align the sheets of paper neatly. NOTE Make sure that the Paper Guide Plates are in touch with the edge of the paper stack. Printing Procedure 2 Slide the Paper Guide Plate to the size of the paper. 5 Close the Manual Staple Tray Cover. 1134O039AA 3 Insert a neat stack of papers face down into the Staple Tray.
3-9 3. Selecting the Finishing 4115O055CA 7 Press set. . This staples the paper stack or 1155O038AA Useful Tip This feature is useful for stapling document sets after making prints. 8 Open the Manual Staple Tray Cover and remove the stapled paper stack. 1155O760AA 9 Close the Manual Staple Tray Cover. Di620PE Operator’s Manual Printing Procedure Chapter 3 You have a choice of the following three stapling positions.
3-10 3. Selecting the Finishing Folding Printing Procedure Chapter 3 Crease makes a crease in the print at its center before it is fed out. A3L, B4L, A4L, 11″×17″L, LetterL Make sure to select the correct stapling function when making prints with the Crease function if you want to make a stapled print set.
3-11 3. Selecting the Finishing Z-Fold folds the print into three parts with the print surface inside as shown below. Sizes of paper that can be loaded: 11″×17″L, A3L * The finished print size has a length half that of the paper loaded in the printer. 1155O642EA Number of sheets: 2~10. NOTES • Even if screen settings are made to make 2-sided prints, the prints to be Z-Folded will be 1-sided.
3-12 3. Selecting the Finishing Auto Dual Function Auto Dual Function in Finishing Mode Though the Top Offset Tray can hold only up to 100 sheets, the Auto Dual function permits making prints of up to 2,100 sheets.
3-13 3.
3-14 3. Selecting the Finishing Note on Stapling When prints are made using the stapling function, the stapled print sets may not be neatly stacked on the tray or may even fall off the tray unless certain conditions are met regarding the number of prints to be stapled and the number of print sets to be made. Use the following table as guide when making prints. 2 prints 3 to 5 prints 6 to 10 prints 11 to 20 prints 21 to 30 prints 31 to 40 prints 41 to 50 prints Printing Procedure Chapter 3 No.
When a Message Appears Di620PE Operator’s Manual When a Message Appears Chapter 4 Chapter 4 4-1
4-2 1. When the Message “The current Paper Tray is empty.” Appears When the tray currently selected for use runs out of paper, the message shown on the left appears. The current print cycle is interrupted and you cannot start a new print cycle. The blinking drawer has run out of paper. Add paper by using the following procedure. The current Paper Tray is empty. Adding paper When a Message Appears Chapter 4 Tray 1 1 Slide out Tray 1. 3 Slide the Tray back in.
4-3 1. When the Message “The current Paper Tray is empty.” Appears Tray 2 1 Slide out Tray 2. 4 1161O096DA 1161O104DA Slide the Edge Guides in the direction of the arrow to suit the paper size. 1161O097DA 3 Load the paper stack into the Tray so that its front side faces down. 1161O099DA NOTE The paper should be loaded no higher than the ▼ (Max. Level Indicator). Ma. 1145O555KA Di620PE Operator’s Manual When a Message Appears Chapter 4 2 Slide the Tray back in.
4-4 1. When the Message “The current Paper Tray is empty.” Appears Tray 3 1 Press the Paper Descent Key and then slide the Tray out. 3 Load another paper stack into the left half of the Tray, front side face down. Press the leading edge of the paper stack tightly up against the left side of the Tray. Chapter 4 1075O049BA Indication of the Paper Descent Key Steady Light: Tray 3 has run out of paper when a Tray other than the 3rd is currently selected for 1136O146AA use.
4-5 1. When the Message “The current Paper Tray is empty.” Appears Large Capacity Cassette 1 Holding the Door Lock Release Lever, open the Cassette Door. NOTES • Make sure that the leading edge of the paper stack is pressed tightly up against the Guide Plate on the take-up side of the Cassette. • The paper should be loaded no higher than the ▼ (Max. Level Indicator). Ma. 1145O555KA 1134O055AA 3 Close the Cassette Door.
4-6 2. When the Message “Replenish Toner.” Appears The message shown on the left appears when toner is soon running out. You can still make prints, but the image density will become lighter and lighter. It is recommended therefore that you replace the Toner Bottle as soon as possible. Replenish Toner Chapter 4 When toner has run out, the message shown on the left appears and you can no longer start a new print cycle. Replace the Toner Bottle with a new one by following the procedure given below.
4-7 2. When the Message “Replenish Toner.” Appears 4 Shake the new Toner Bottle well and turn it over lengthwise five times. 7 Swing the Toner Bottle Holder closed and close the Front Door. 1075O059AA With the “UP” marking on top, insert the Bottle into position. Check that the marking on the Bottle is aligned with the marking on the Toner Bottle Holder. 4115O046AA 6 NOTES • Use ONLY the specified toner for this printer. Using any other toner could result in trouble.
4-8 3. When the Message “The Staple Cartridge is empty.” Appears The message shown on the left appears when the staples are running out. Replace the Staple Cartridge with a new one by following the procedure given below. Replenish Toner When a Message Appears Chapter 4 Replacing the Staple Cartridge Holding the Finisher Lock Release Lever, slide the Finisher away from the printer.
4-9 3. When the Message “The Staple Cartridge is empty.” Appears NOTE Check that no portion of the staple sheet hangs out of the cartridge. Break off any portion of the sheet that hangs out of the cartridge. Slide the Finisher back against the printer. 8 4115O015AA 1134O076AA Insert the new Staple Cartridge until it clicks into position. 1155O038AA 1155O070AA 7 Push the Staple Unit back in and close the Finisher Front Door. Remove the sheet of paper to check that it has been properly stapled.
4-10 3. When the Message “The Staple Cartridge is empty.” Appears 1 4 Remove the empty staple clip from the Staple Cartridge. Press and turn the knob and open the cover at the rear of the Finisher. 1166O129AA 1155O766AA Load a new staple clip into the Staple Cartridge and carefully peel off the Seal. Pull the Stapler Unit out of the well.
4-11 3. When the Message “The Staple Cartridge is empty.” Appears 8 Press and turn the Knob to lock the cover. 1155O767AA When a Message Appears Chapter 4 NOTES • Replace the Staple Cartridge only after you are prompted to do that by the message. Removing the Staple Cartridge before then will result in stapling trouble.
4-12 4. When the Message “A paper misfeed has been detected.” Appears If a paper misfeed occurs during a print cycle, the message shown on the left appears and that particular print cycle is stopped in the middle of operation. Clear the misfed sheet of paper according to the procedure given below. 4115O016CA When a Message Appears Chapter 4 Misfeed Location Displays Different procedures are used to clear a misfed sheet of paper depending on the location.
4-13 4. When the Message “A paper misfeed has been detected.” Appears Large Capacity Cassette p. 4-18 Intelligent Manual Feeding Tray p. 4-19 4115O019AA 4115O024AA 4115O026AA 4115O027AA 4115O028AA 4115O029AA 4115O030AA 4115O031AA 4115O032AA Finisher FN-102 p. 4-28 4115O033AA Di620PE Operator’s Manual 4115O034AA 4115O035AA 4115O036AA When a Message Appears 4115O025AA Chapter 4 Finisher FN-3 p.
4-14 4. When the Message “A paper misfeed has been detected.” Appears Misfeed Clearing Procedures Printer 1 Open the Misfeed Clearing Guide pull out the sheet of paper. L1 , 6 Open the Right Door. L1 1155O079AA 1155O558AB 7 Turning Knob M2 , pull out the sheet of paper. When a Message Appears Chapter 4 2 Open the Left Door. M2 1155O076AA 3 Open the Front Door. 1155O080AA 8 9 4115O047AA 4 Turning Knob M1 , pull out the sheet of paper.
4-15 4. When the Message “A paper misfeed has been detected.” Appears 11 Raising Misfeed Clearing Guide M6 , remove the sheet of paper. 15 16 Close the Front Door. Slide out the Tray being used and take out the paper stack left in it. M6 1155O083AA 12 Turn Knob M7 and remove the sheet of paper. 1075O068AA Reload the paper stack and slide the Tray into the printer. Chapter 4 17 M7 13 1075O069AA M8 18 To reset the paper misfeed indication on the Panel, open and close the Front Door.
4-16 4. When the Message “A paper misfeed has been detected.” Appears Duplex Unit 1 Open the Left Door. 6 Turning Knob M2 , pull out the sheet of paper. M2 1155O076AA 1155O080AA 7 8 Chapter 4 2 Open the Front Door. Close the Right Door. Slide out Duplex Unit D2 . When a Message Appears D2 4115O047AA 3 Turning Knob M1 , pull out the sheet of paper. Then turn Knob D1 to return any paper to the Duplex Unit. 1155O089AA 9 Raising Misfeed Clearing Guide D3 , remove the sheet of paper.
4-17 4. When the Message “A paper misfeed has been detected.” Appears 11 Raising Misfeed Clearing Guide D5 , remove the sheet of paper. D5 1155O092AA Slide Duplex Unit D2 back into the printer. Chapter 4 12 D2 13 Close the Front Door. Useful Tip After the paper misfeed has been cleared, the printer automatically resumes a print cycle without the Start Command.
4-18 4. When the Message “A paper misfeed has been detected.” Appears Large Capacity Cassette 1 Press the Paper Descent Key. 5 Remove the sheet of paper. 1134O031AA 1134O029AA Holding the Door Lock Release Lever, open the Cassette Door and remove the sheet of paper. 6 Slide the Cassette back against the printer. When a Message Appears Chapter 4 2 1134O030AA 1134O027AA 3 Close the Cassette Door. 1134O033AA 4 Press the Lock Release Lever and slide the Cassette away from the printer.
4-19 4. When the Message “A paper misfeed has been detected.” Appears Intelligent Manual Feed Tray 1 Unload the paper stack from the Manual Feed Tray and open the Right Door. Pull out the sheet of paper from the Paper Take-Up Section. Then, close the Right Door. 1155O087AA 3 Place the paper stack back on the tray. 1075O073AA 4 To reset the paper misfeed indication on the Touch Panel, open and close the Front Door.
4-20 4. When the Message “A paper misfeed has been detected.” Appears Finisher FN-3 4 Close the Misfeed Clearing Guide and tighten the screws. 5 Open the Finisher Front Door. 4115O037AA 1 Holding the Finisher Lock Release Lever, slide the Finisher away from the printer. 6 Chapter 4 When a Message Appears 1155O067AA 4115O014AA 2 Raising Misfeed Clearing Guide FN3 , remove the sheet of paper. FN3 Opening Misfeed Clearing Guide FN1 , remove the sheet of paper.
4-21 4. When the Message “A paper misfeed has been detected.” Appears Remove the sheet of paper and close Misfeed Clearing Guide FN4 . 13 1155O645AA FN4 1155O410AA 14 Slide the Finisher back against the printer. Turn Knobs FN7 and FN6 to feed the sheet of paper. FN7 FN6 4115O015AA 1155O411AA 11 Pinching the lever of Misfeed Clearing Guide FN5 , open FN5 . FN5 1155O412AA 12 Remove the sheet of paper and close FN5 .
4-22 4. When the Message “A paper misfeed has been detected.” Appears 4 Remove the sheet of paper and close FN8 . FN8 4115O038AA 1 Holding the Finisher Lock Release Lever, slide the Finisher away from the printer. 1155O415AA Chapter 4 5 Turn Knobs FN7 and sheet of paper. FN6 to feed the FN7 FN6 When a Message Appears 4115O014AA 2 Open the Finisher Front Door. 1155O411AA 6 FN5 1155O067AA 3 Pinching the lever of Misfeed Clearing Guide FN5 , open FN5 .
4-23 4. When the Message “A paper misfeed has been detected.” Appears 8 Close the Finisher Front Door. 4115O039AA 1155O645AA 9 Slide the Finisher back against the printer. 1 Open Exit Tray sheet of paper. FN9 and remove the Chapter 4 FN9 2 3 Close FN9 . Open Manual Staple Tray Cover FN10 and remove the sheet of paper. FN10 1155O425AA 4 Di620PE Operator’s Manual Close FN10 .
4-24 4. When the Message “A paper misfeed has been detected.” Appears 4 Turn Knob paper. FN2 to feed the sheet of FN2 4115O040AA Holding the Finisher Lock Release Lever, slide the Finisher away from the printer. 1155O408AA 5 Open Misfeed Clearing Guide FN4 . Chapter 4 1 FN4 When a Message Appears 4115O014AA 2 Open the Finisher Front Door. 1155O409AA 6 Remove the sheet of paper and close Misfeed Clearing Guide FN4 .
4-25 4. When the Message “A paper misfeed has been detected.” Appears 8 Pinching the lever of Misfeed Clearing Guide FN5 , open FN5 . 11 Check to see if a sheet of paper is left in the Finisher. If any is visible, perform step 10 once again. FN5 1155O412AA NOTE Sliding out Paper Folding Unit PF2 with a sheet of paper left inside could result in a malfunction. 12 FN5 Open Misfeed Clearing Guide FN4 . 1155O413AA 10 Turn Knobs FN2 and PF1 together five turns to feed the sheet of paper.
4-26 4. When the Message “A paper misfeed has been detected.” Appears 14 Turn Knobs FN7 the sheet of paper. and FN6 to feed 18 Opening Misfeed Clearing Guide remove the sheet of paper. PF3 , FN7 FN6 PF3 1155O411AA Pinching the lever of Misfeed Clearing Guide FN5 , open FN5 . 19 Raise Misfeed Clearing Guide Chapter 4 15 1155O418AA PF4 . PF4 When a Message Appears FN5 1155O419AA 1155O412AA 16 Remove the sheet of paper and close FN5 .
4-27 4. When the Message “A paper misfeed has been detected.” Appears 22 PF6 , Opening Misfeed Clearing Guide remove the sheet of paper. PF6 1155O423AA PF2 back into PF2 1155O422AA 24 Close the Finisher Front Door. 1155O645AA 25 Slide the Finisher back against the printer. 4115O015AA Di620PE Operator’s Manual Chapter 4 Slide Paper Folding Unit the printer.
4-28 4. When the Message “A paper misfeed has been detected.” Appears Finisher FN-102 1 Holding the Finisher Lock Release Lever, slide the Finisher away from the printer. 4 1155O740AA 4115O041AA When a Message Appears Chapter 4 2 If “Hole Punch” has been set, turn the Hole Punch Adjustment Dial ten times upward. Remove the sheet of paper. Open Misfeed Clearing Guide FN3 and remove the sheet of paper. 5 Open Misfeed Clearing Guide FN4 and remove the sheet of paper.
4-29 4. When the Message “A paper misfeed has been detected.” Appears 8 Open Misfeed Clearing Guide FN9 and remove the sheet of paper. 12 Close Misfeed Clearing Guide FN2 . 1166O172AA 1155O744AC 13 Open Misfeed Clearing Guide FN1 . Chapter 4 9 Open Misfeed Clearing Guide FN7 at the right side of the Finisher. 10 14 Remove the sheet of paper. Remove the sheet of paper and close Misfeed Clearing Guide FN1 . 1155O746AC 1166O174AA 11 Close Misfeed Clearing Guide FN7 .
4-30 5. When a Staple Misfeed Occurs Clearing the Staple Misfeed If a staple misfeed occurs, the message shown on the left appears. Clear the staple misfed according to the procedure given below. When a Message Appears Chapter 4 4115O042CA 1 Open Misfeed Clearing Guide FN1 . 4 1166O127AA 1166O173AA 2 Remove the sheet of paper and close Misfeed Clearing Guide FN1 . 5 Press and turn the knob to open the cover at the rear of the Finisher.
4-31 5. When a Staple Misfeed Occurs 7 Return the guide back to its original position. 1166O178AA Insert the Staple Cartridge into the Stapler Unit until it clicks into place. Chapter 4 8 9 Align the arrows and firmly push the Stapler Unit down into the well. 1166O131AB 10 Press and turn the knob to lock the cover. 1155O767AA NOTE If the finisher does not staple after clearing the staple misfeed, call your Tech. Rep.
4-32 6. What Does Each Message Mean? When a Message Appears Chapter 4 What does each message mean? Message A malfunction was detected. The SMART controller has called your Technical Representative. Please add toner. Follow the instructions on label inside of Front Door. Cause The printer malfunctioned and is unable to make prints. Action Call and inform your Technical Representative of the code being shown on the screen. Toner has run out and the printer is unable to make prints.
5-1 Troubleshooting Troubleshooting Chapter 5 Chapter 5 Di620PE Operator’s Manual
5-2 1. When This Type of Print is Produced When this type of print is produced When there is a problem with the print image quality, check both the print size and printer driver options. Symptom The image is too light. Possible Cause The Toner Bottle has just been replaced. The message “Replenish Toner.” is shown on the Screen. The paper is damp. Action The printer needs more toner. Replenish toner by using Toner Replenisher of Utility Mode. Replace the Toner Bottle. ☞p. 4-6 Change the paper. ☞p.
5-3 2. The Printer is not Functioning as Designed The printer is not functioning as designed Symptom The power indicator is off. The icon is red with black stripes. The power indicator is blinking slowly. The printer is not activated when the Power Switch is turned ON. (Power Indicator is dark on the Panel) Check for Auto Shut Off is activated. Action Turn the Power Switch ON. Power save mode is activated. Power save mode is canceled when a job is executed.. Plug the power cord into the power outlet.
5-4 Troubleshooting Chapter 5 2.
6-1 Chapter 6 Miscellaneous Chapter 6 Miscellaneous Di620PE Operator’s Manual
6-2 1. Specifications Specifications Printer Di620PE Type Photoconductor Printing System Developing System Fusing System Resolution Type Copy Paper Size Warm-Up Time First Print Print Speed (Approx. prints/minute) Lost Image Power Requirements Power Consumption Dimensions Weight Miscellaneous Chapter 6 Tray Capacity Console Type Printer OPC Electrostatic Dry Powdered Image Transfer to Plain Paper Micro-Toning System Lamp-Heated Roller 400dpi Plain Paper (60 g/m2 to 90 g/m2, 16 lbs. to 24 lbs.
6-3 1. Specifications Large Capacity Cassette C-304 Kinds of Paper Paper Size Capacity Power Source Power Consumption Dimensions Weight Plain paper (60 g/m2 to 90 g/m2, 16 lbs. to 24 lbs.), Recycled paper A4C, Letter C 3,000 sheets (80 g/m2), 3,400 sheets (20 lbs.) Supplied from printer 30W or less Width: 278 mm (11-1/2″) Depth: 446 mm (17-1/2″) Height: 500 mm (19-3/4″) 14.2 kg (31-1/4 lbs.) Large Capacity Cassette C-304L Plain paper (60 g/m2to 90 g/m2, 16 to 24 lbs.
6-4 1. Specifications Finisher FN-3 Types of Trays Modes Kinds of Paper Capacity of Bins Punching Power Source Power Consumption Dimensions Weight Accessories Top Offset Tray, Bottom Offset Tray Non-Sort Mode, Sort Mode, Group Mode, Staple Mode, Hole Punch Mode and Folding Mode Non-Sort Mode, Sort Mode and Group Mode • Plain paper (60 g/m2 to 90 g/m2, 16 lbs. to 24 lbs.
6-5 1.
6-6 1. Specifications Finisher FN-102 Types of Trays Modes Kinds of Paper Paper Size Chapter 6 Capacity Stapling Miscellaneous Punching Power Source Power Consumption Dimensions Weight Accessories Top Offset Tray, Elevator Tray Non-Sort Mode, Shift (Sort/Group) Mode, Staple Mode, Hole Punch Mode Top Offset Tray • Non-Sort Mode: Plain paper (60 g/m2 to 90 g/m2, 16 lbs. to 24 lbs.), Recycled paper Exclusive paper Thick paper (91 g/m2 to 157g/m2, 24-1/4 lbs. to 41-3/4 lbs.
6-7 2. Care of the Printer Cleaning (Turn OFF the Power Switch of the printer when cleaning.) Housing Front Door Wipe the surface of the housing clean with a soft cloth dampened with alcohol. 1 2 Swing down the Front Door. Wipe the surface of the Front Door clean with a soft, dry cloth.
6-8 3.
6-9 4.
Copyright 1999 MINOLTA CO., LTD. Made in Japan The information contained in this manual is subject to change without notice to incorporate improvements made on the product or products the manual covers. MINOLTA CO., LTD. Image Information Products Marketing Headquarters 1999.
