SERVICE HANDBOOK INSTRUCTION MANUAL KONICA CORPORATION TECHNOLOGY SUPPORT CENTER TOKYO JAPAN INSTRUCTION MANUAL 7415
Legal Restrictions on Copying Certain types of documents must never be copied by the machine for the purpose or with the intent to pass copies of such documents off as the original. The following is not a complete list but is meant to be used as a guide to responsible copying.
Thank you very much for your purchase of the Konica 7415. This operator’s manual explains how to operate the machine and replenish its supplies. It also gives some troubleshooting tips as well as general precautions to be observed when operating the machine. To ensure the best performance and effective use of your machine, read this manual carefully until you familiarize yourself thoroughly with its operation and features. After you have read through the manual, keep it for ready reference.
i Contents Chapter 1 Safety Notes ............................................................................ 1-1 1. Using This Manual ...........................................................................1-2 Caution Labels ..........................................................................1-3 Internal Laser Radiation ...........................................................1-4 Laser Safety Label ....................................................................1-4 2.
ii Contents Chapter 5 When an Indicator Lights Up ................................................. 5-1 1. Display Messages .............................................................................5-2 2. The Toner Empty Indicator ..............................................................5-4 How to replace the supply unit .................................................5-4 3. Paper Empty Indicator ......................................................................
iii Terms and Symbols for Original Types and Copy Paper A few special terms and symbols are used in this manual to designate types of originals and copy paper. This page explains about these terms and symbols. Feeding Direction (copy paper path) Paper that has been loaded into the machine will be fed from the right side. The copies will be output facedown from the central part of the machine.
Safety Notes Chapter 1 1-1 Chapter 1 Safety Notes
1-2 1. Using This Manual Safety Notes Chapter 1 Since laser light emitted inside the copier is completely confined within internal protective housings and external covers, the laser beam cannot escape from the machine during any phase of user operation.
1-3 1. Using This Manual The caution labels are attached to the machine areas, as shown, when you are advised to pay special attention to avoid any dangerous situations or serious injury. ATTENTION VORSICHT PRECAUCION ATTENZIONE temperatura! Heiße Oberfläche! ¡ Temperatura alta Alta ! High temperature! Température élevée! Non toccare. Agire Brandverletzungsgefahr. No tocar. Tener Do not touch. Use Risque de brûlure.
1-4 1. Using This Manual Internal Laser Radiation Safety Notes Chapter 1 Maximum Radiation Power: 1.03 mW at the laser aperture of the print head unit. Wavelength: 770–810 nm This product employs a Class 3b Laser Diode that emits an invisible laser beam. The Laser Diode and Scanning Polygon Mirror are incorporated in the print head unit. The print head unit is NOT A FIELD SERVICE ITEM. Therefore, the print head unit should not be opened under any circumstances.
1-5 2. Installing the Copier • A plug socket is limited in capacity. Use only a power source with the correct rating for the machine; otherwise, hazardous situations such as smoking or overheating may occur. See the to match the power supply and power consumption: a) 230V/50 Hz: Less than 3.5A b) 230V/60 Hz: Less than 3.5A • Avoid multiple connections in the same outlet. Do not use multiple outlet adaptors. CAUTION: Power Plug and Lead • Be sure to insert the power plug firmly into the power socket.
1-6 2. Installing the Copier Chapter 1 CAUTION: Temperature and Humidity • Keep away from direct sunlight, heat sources such as stoves, cool air from an air conditioner and hot air from a heater. • Avoid any environment that is outside the range shown below: Temperature: 10–30°C with a fluctuation of up to 10°C per hour. Humidity: 15–85% with a fluctuation of up to 20% per hour. • Maintain the installation place well-ventilated. • Keep away from dust or corrosive gases.
1-7 3. Precautions for Routine Handling CAUTION: Prevention of Fire Do not use volatile combustibles such as a thinner or alcohol near the machine. CAUTION: Prohibition of Machine Modification Do not modify or remove any parts by yourself. CAUTION: Prevention of Machine Troubles • Do not drop small metallic objects such as paper clips or staple inside the machine. • Do not place any heavy or hard objects such as a vase, books or ornaments on the machine.
Safety Notes Chapter 1 1-8
Chapter 2 Getting to Know Your Machine Getting to Know Your Machine Chapter 2 2-1
2-2 1. The Various Parts of the Machine Parts of the machine and what they do Automatic Document Feeder DF-216
2-3 1. The Various Parts of the Machine Options 2 1 4 5 C4007O095CA Automatic Document Feeder
2-4 1. The Various Parts of the Machine Getting to Know Your Machine Chapter 2 Parts of the machine and what they do 1 2 4 5 3 C4007O089CA C4007O097CA Copy Tray: Copies are output into this tray. Paper Tray: Holds up to 250 sheets of paper. Manual Bypass Tray: Use to feed paper into the machine manually. ☞ p. 3-7 Control Panel: Use to control copy and other functions of the unit. ☞ p. 2-6 Power Switch: Use to turn power to the unit ON and OFF. ☞ p.
2-5 1. The Various Parts of the Machine Inside the Machine 2 4 Getting to Know Your Machine Chapter 2 3 5 1 C4007O098CA C4007O099CA Lock Release Lever: Pulled when replacing the supply unit or removing paper misfeeds. Original Pad: Secures the original for copying. Original Glass: Original is placed on top of this surface for copying. Upper Half of Machine: Opened under the following circumstances: • When replacing the supply unit. ☞ p. 5-4 • When clearing a misfeed. ☞ pp.
2-6 2. The Functions of the Control Panel Control Panel Getting to Know Your Machine Chapter 2 3 4 Start Key • Press to start a copy cycle. Clear/Stop Key • Press to cancel a copy operation. • Press to reset the Copies setting to “1”. ☞ p. 3-11 • Press to return the zoom ratio setting to 100%. ☞ p. 3-13 • Press for three seconds to enable the total check function. ☞ p. 4-3 Paper Select Key • Press to select the drawer that contains the desired paper size. ☞ p.
2-7 C/ 7 8 9 0 2 1 C4007O001DA Display Panel Add Toner Indicator Indicates that the toner supply is running low. Replace the supply unit. ☞ p. 5-4 Add Paper Indicator Indicates that the selected drawer is out of paper. Replenish the paper supply. ☞ p. 5-6 Getting to Know Your Machine Chapter 2 2.
2-8 3. Turning the Machine ON and OFF and Enabling the Initial Mode Turning ON and OFF • Turning the Machine ON Press the Power Switch to the • Turning the Machine OFF Press the Power Switch to the (OFF) position. HINTS: If you turn off the Power Switch in sleeping mode, the green light of Start Key does not turn off for a while. Chapter 2 Getting to Know Your Machine (ON) position. C4007O100CA When the Machine is Turned ON The unit will enter a warm up mode.
2-9 4. Auxiliary Functions Auto Panel Reset Function The unit automatically returns to the Initial Mode without pressing the Clear/Stop Key one minute after a copy operation has completed or one minute after the last operation key was pressed. Useful Tip The period of time before the Sleep Function is enabled can be changed through the User’s Choice Mode. Please refer to the section of this manual that explains the “User’s Choice Mode” for details. ☞ p.
Getting to Know Your Machine Chapter 2 2-10
Making Copies Making Copies Chapter 3 Chapter 3 3-1
3-2 1. How to Copy Documents • Generally, full size copies are reproduced at a zoom ratio of 100%. To make a full-size copy on paper of the same size as the original, set the document (step 1), specify the number of copies to be generated (step 6), and press the Start Key (step 7). (* The default paper tray, zoom ratio and auto exposure settings are automatically selected in the Initial Mode.) • Performing the operations indicated by the copy as well as enable the 2in1 Mode.
3-3 1. How to Copy Documents 4. Selecting the Copy Density Mode. • Press the Exposure Control Keys to specify the desired level of density. ☞ p. 3-14 C4007O004DA To change the Function Mode C4007O005DA 5. Selecting the Function Mode. • Use the Copies/Function Key to specify the desired Function Mode. ☞ p. 3-16 C4007O006DA 6. Specifying the number of copies to be made. • Use the Key or Key to specify the number of copies or groups of documents to be copied. ☞ p.
3-4 2. Setting the Original Document When using the Automatic Document Feeder With the Automatic Document Feeder, originals placed into the Document Feed Tray are fed in one sheet at a time, copied, then fed out. Please follow the instructions provided when using this device. Failure to follow these instructions may cause a misfeed, damage to the original or other complications.
3-5 2. Setting the Original Document Setting the original onto the glass General Documents Transparent Documents Open the Original Cover. Set the document onto the glass with the side that you wish to copy facing down. 1 Follow the same procedure as described for general documents. Chapter 3 1 2 Align the centre of the original with the scale marker.
3-6 3. Selecting Paper Trays How to select a paper tray Paper trays are selected using the Paper Select Key. You can select from the Paper Drawer, the Paper Feed Unit and the Manual Bypass Tray depending on the configuration of your copy application. Chapter 3 C/ C4007O007DA The paper tray options can be selected as follows by pressing the Paper Select Key.
3-7 3. Selecting Paper Trays Using the Manual Bypass Tray Use this tray to copy documents onto paper that is not otherwise loaded into the machine or to copy onto OHP transparencies or specialty paper types. Paper and media supported by the Manual Bypass Tray * When the Manual Bypass Tray is selected, the paper size and type appear in the display. Use the Key and Key to change these settings to match the size and type of the installed paper. Each press of the keys changes the settings as shown below.
3-8 3. Selecting Paper Trays Loading the paper (standard sizes) Making Copies Chapter 3 1 2 Set the original document. 4 Insert the paper as far as possible into the Manual Bypass Tray. Be sure to adjust the Document Guide Plates to fit the paper. Select the proper paper size and type using the and Keys. (Example) Regular paper (A4 size) C4007O015DA C4007O105CA NOTES • Be sure to feed the paper one sheet at a time. • Curl the edges of the paper upwards before setting the paper into the machine.
3-9 3. Selecting Paper Trays Loading the paper (non-standard sizes/free sizes) 1 2 Set the original document. 4 Press the Key or the display “U8”. 5 Press the Start Key. Key to Insert the paper as far as possible into the Manual Bypass Tray. Be sure to adjust the Document Guide Plates to fit the paper. C4007O105CA NOTES • Be sure to feed the paper one sheet at a time. • Curl the edges of the paper upwards before setting the paper into the machine.
3-10 3. Selecting Paper Trays 8 Press the Key or the Key to display the paper length code. Refer to “Manual Feed Input Size” for details. ☞ pp. 4-6, 4-7 (Example) Paper Length: 195 mm the Manual Bypass Tray by pressing 11 Select the Paper Select Key. C4007O014DA the 12 Press display “P”. Key or the Key to NOTE The value entered for the paper length must be larger than the entered paper width.
3-11 4. Specifying the Number of Copies How to specify the number of copies to be generated The number of copies to be generated can be specified by using the Key and Each press of the Key increases the number value by one. Each press of the number value by 10. Key. Key increases the C/ 1 (Example: Specifying 23 copies.) Press the Key twice. NOTE Press the Clear/Stop Key if the wrong number of copies is entered. C4007O066CA 2 Press the C/ Key three times.
3-12 5. Specifying the Zoom Ratio How to specify the zoom ratio The zoom ratio can be specified by pressing the Zoom Key. There are two modes to choose from: Standard Copy Zoom and Manual Zoom Select. Making Copies Chapter 3 C/ C4007O017DA Standard Copy Zoom Mode With this mode, the most often used preset zoom settings can be selected. Press the Zoom Key to enable the Copy Zoom Setting Mode. The following zoom settings can be selected by pressing the Zoom Key.
3-13 5. Specifying the Zoom Ratio Manual Copy Zoom Settings The zoom ratio can be adjusted in single increments with each press of the / Keys. (Range: 50–199 %) Press and hold a or Key to rapidly change the zoom ratio. Press the Zoom Key to enter the Copy Zoom Setting Mode. 2 Set the zoom ratio using the Keys. C4007O018DA and C4007O047CA Useful Tips • To return the setting to 100%, press the Clear/ Stop Key while in the Copy Zoom Setting Mode.
3-14 6. Selecting the Copy Image Density Mode How to select the copy image density The copy image density can be selected by pressing the Auto Exposure Mode Key and the Image Density Key. There are three modes to choose from: Auto Exposure, Manual Exposure and the Photo. C/ Making Copies Chapter 3 A / C4007O016DA Auto Exposure Mode Manual Exposure Mode This mode automatically selects the exposure setting that is optimal for the original document to be copied.
3-15 6. Selecting the Copy Image Density Mode Photo Mode Photo Mode is used for copying documents containing halftones such as photos. This mode allows you to select from nine levels of exposure. 1 Press the Auto Exposure Mode Key to select the Photo Mode. Useful Tips • Both the Manual Exposure Mode and the Photo Mode allow you to select from nine levels of exposure. • The indicators appear as follows to indicate the selected exposure level.
3-16 7. Selecting the Function Mode How to select the Function Mode The Function Mode can be selected by pressing the Copies/Function Key. There are four modes to choose from: Non-Sort Mode, 2in1 Non-Sort Mode, Sort Mode and 2in1 Sort Mode. C/ F1-F4 A / Making Copies Chapter 3 C4007O021DA Select the Function Mode Press the Copies/Function Key to enable the Function Mode. The following Function Modes can be selected by pressing the F1 : Non-Sort F2 : 2in1-Non-Sort / F3 : Sort Keys.
3-17 7. Selecting the Function Mode F1: Non-Sort This mode outputs copies of original documents just as they are loaded into the machine. Copies 2 2 2 3 3 3 C4007O132CA F2: 2in1 Non-Sort (Requires installation of expansion memory) Copies Originals 1 2 3 4 1 2 1 2 1 2 3 4 3 4 3 4 Copies two original documents onto one sheet of paper and outputs the results in the same order as they were loaded into the machine.
3-18 7. Selecting the Function Mode F4: 2in1 Sort (Requires installation of the Automatic Document Feeder and expansion memory) Copies two original documents onto one sheet of paper and automatically outputs them into complete sets. Copies Originals 1 2 3 4 1 2 3 4 1 2 3 4 Making Copies Chapter 3 1 2 3 4 C4007O135CA Useful Tip The Initial Mode’s default setting when the Automatic Document Feeder and Expansion Memory are installed is the Sort Mode.
3-19 7. Selecting the Function Mode Notes for using the Function Mode The Function Mode Indicator • The Function Mode indicator will become lit when settings other than the Initial Mode are selected. • The Zoom indicator will become lit and the zoom ratio will automatically be decreased when F2 (2in1 Non-Sort) or F4 (2in1 Sort) are selected. 2in1 Copying When using the 2in1 function, it is important to set the original documents correctly to prevent them from being output in reverse order.
Making Copies Chapter 3 3-20
Using the User’s Choice Mode Using the User’s Choice Mode Chapter 4 Chapter 4 4-1
4-2 1. The Total Check Function How to read the Total Check Function displays This machine can keep a count of the number of copies that it has generated since it was first set up. ◆ Total Count Shows the total number of copies since the machine was installed. ◆ PM Count Shows the number of copies taken since the last replacement of PM parts. Count Displays Count displays appear as shown below.
4-3 1. The Total Check Function How to select a Total Check Function 1 Press and hold the Clear/Stop Key for three seconds. The Total Count will be displayed. C/ C4007O075CA Press and hold the Clear/Stop Key again, for three seconds, to display the PM Count. C/ C4007O076CA 3 Press the Clear/Stop Key to return to the previous status mode.
4-4 2. User’s Choice Mode This mode allows you to determine the default settings for functions that are activated when the main power switch is turned on or the panel is reset with the Auto Panel Reset Function. The User’s Choice Mode is used to program the most commonly used settings of the machine into the Initial Mode.
4-5 2. User’s Choice Mode U3: Disable Sleep Function Completely disables the Sleep Function Mode. Code Setting 1 Turns OFF the Disable Sleep Function Mode. 2 Enables the Disable Sleep Function Mode. Default U4: Exposure Mode Priority Allows you to select the optimal exposure mode or the Photo Mode from the Initial Mode.
4-6 2. User’s Choice Mode U7: Paper Size Select Allows you to assign a particular paper size to the paper tray. Code Setting 1 A4 R 2 A5 R Default U8: Manual Feed Input Size Allows you to specify a paper size when loading non-standard size paper into the Manual Bypass Tray.
4-7 2.
4-8 2. User’s Choice Mode U9: Density (Automatic Document Feeder) Allows you to specify the density level when an original document is set into the Automatic Document Feeder. Code Setting 1 Recommended for general copying purposes (text documents). 2 Recommended when copying lighter or faded original documents. Default * Only displayed when the Automatic Document Feeder has been installed onto the machine. U0: Function Mode Allows you to specify the initial settings of the Function Mode.
4-9 2. User’s Choice Mode UC: Tray Priority (for Printer Mode) Allows you to set the prioritized tray for feeding paper into the machine when outputting documents from a personal computer. Code Setting 1 Auto Select 2 Paper Tray 3 Paper Feed Unit Default Using the User’s Choice Mode Chapter 4 * This function is displayed only when the Print Controller is installed.
4-10 2. User’s Choice Mode How to select User’s Choice Settings 1 Press and hold the Exposure Control Key (Lighter) for three seconds to enter the User’s Choice Mode. “U1” will be displayed. 3 Press the Start Key. The currently selected User’s Choice Code will be displayed. C4007O077CA C4007O072CA Using the User’s Choice Mode Chapter 4 2 The User’s Choice Codes will rotate as shown below when the Key and Key are pressed.
4-11 2. User’s Choice Mode 6 Press the Clear/Stop Key to return to the previous status mode. C/ C4007O073CA Using the User’s Choice Mode Chapter 4 * The User’s Choice Mode will be cancelled and the previous status mode will be enabled.
Using the User’s Choice Mode Chapter 4 4-12
5-1 Chapter 5 When an Indicator Lights Up Chapter 5 When an Indicator Lights Up
5-2 1. Display Messages Error Indicator Cause Toner Empty Response The toner supply inside of the supply unit has been depleted. Replace the supply unit using the procedure provided. ☞ p. 5-4 The paper supply has been depleted. Replenish the paper supply using the procedure provided. ☞ p. 5-6 Paper has been misfed somewhere within the machine. Clear the paper misfeed using the procedure provided. ☞ p. 5-8 Paper has been misfed somewhere within the machine.
5-3 1. Display Messages Error Indicator Cause Response An internal error has occurred. Reset the machine using the procedure provided. ☞ p. 5-12 The Upper Half of the Machine is open. Make sure that the Upper Half of the Machine is securely closed. The Automatic Document Feeder is open. Make sure that the Automatic Document Feeder is securely closed. The Paper Misfeed Guide of the Automatic Document Feeder is open.
5-4 2. The Toner Empty Indicator The error indicator displayed here will appear when the toner supply inside of the supply unit has been depleted. The machine will not be operable under these circumstances. Follow the procedure provided below to replace the supply unit when this indicator is displayed. C4007O038CA How to replace the supply unit NOTE Be careful not to touch the areas marked CAUTION: HOT with bare hands. Pull the Lock Release Lever and open the Upper Half of Machine.
5-5 2. The Toner Empty Indicator Useful Tip The supply unit can easily be installed by aligning the front of the unit with the marker provided within the machine. C4007O113CA C4007O114CA NOTE Only use replacement supply unit that were designed for use specifically with this machine. Use of other supply unit may result in irregular machine performance. Chapter 5 Gently swing down and lock the Upper Half of Machine. Then, close the Front Door.
5-6 3. Paper Empty Indicator The error indicator displayed here will appear when the paper supply inside of the machine has been depleted. The machine will not be operable under these circumstances. Follow the procedure provided below to replenish the paper supply when this indicator is displayed. C4007O037CA How to replenish the paper supply Paper Tray 1 Remove the Manual Bypass Tray. NOTE The paper should be loaded no higher than the (Max. Level Indicator).
5-7 3. Paper Empty Indicator Paper Feed Unit 1 Slide out the Paper Drawer and press down the Paper Lifting Plate. 3 Gently slide the Paper Drawer back in. C4007O121CA C4007O141CA 2 Load the paper stack into the Paper Drawer so that its front side faces down. Make sure that the paper stack rests under the two catches of the Paper Drawer. NOTE The following indicator will appear in the display after replenishing the paper: C4007O017CA Chapter 5 The copy job is still saved in the machine’s memory.
5-8 4. Paper Misfeed Indicators If a paper misfeed occurs, the machine will stop operating, the letter “J” will flash alternately with a number or the “PC” indicator will flash. PC Indicator C4007O015CA J Indicator Example: The J2 indicator (Flashing alternately) C4007O013CA C4007O014CA Clearing paper misfeeds PC 4 Remove the Manual Bypass Tray and remove the misfeed. Chapter 5 1 Pull the Lock Release Lever to open and close the Upper Half of the Machine.
5-9 4. Paper Misfeed Indicators J2/J3 1 Press in the tray stoppers, and then remove the Paper Drawer. NOTE Be careful not to touch the areas marked CAUTION: HOT with bare hands. 1 Pull the Lock Release Lever and open the Upper Half of Machine. C4007O163CA 2 Remove the misfed sheet of paper. C4007O109CA Remove the supply unit. C4007O164CA 3 Make sure that the paper is correctly loaded in the Paper Drawer. C4007O110CA CAUTION : HOT The metal parts within the machine are hot.
5-10 4. Paper Misfeed Indicators 4 Remove the misfed sheet of paper. 5 Remove a misfed sheet of paper jammed in the Transport Section by pulling it from the bottom of the Fusing Unit. 7 Close the Upper Half of Machine. C4007O123CA C4007O114CA NOTE The following indicator will appear in the display after clearing the paper misfeed: C4007O017CA The copy job is still saved in the machine’s memory. Press the Start Key to resume operations. C4007O124CA Re-install the supply unit.
5-11 4. Paper Misfeed Indicators J8 1 Remove the original document from the Document Feed Tray. 2 Open the Paper Misfeed Guide and gently remove the paper misfeed. 5 Place the original document that was removed in step 1 into the Automatic Document Feeder again. C4007O125CA C4007O127CA NOTE The following indicator will appear in the display after clearing the paper misfeed: Load the number of pages that are displayed into the Automatic Document Feeder again to proceed with the copy job.
5-12 5. Trouble Indicator If an error occurs within the machine, a “CXXXX” trouble code appears in the display. How to reset the machine Press the Power Switch to turn the machine off, then on again. * Should a “CXXXX” trouble code continue to appear in the display after resetting the machine, please contact your Service Centre. C4007O100CA When an Indicator Lights Up Chapter 5 NOTES • When calling your Service Centre, give him or her the malfunction code shown on the Message Display.
6-1 Chapter 6 Troubleshooting Chapter 6 Troubleshooting
6-2 1. Improving Image Quality Symptom The image is too light. 1074O108 The image is too dark. 1074O109 Troubleshooting Chapter 6 The copy appears blurred. Possible Cause Action A “lighter” exposure level for the Adjust the Auto Exposure Level Auto Exposure Mode has been Priority of the User’s Choice specified. Mode. ☞ p. 4-5 Or, disable the Auto Exposure Mode and adjust settings manually through the Manual Exposure Mode. ☞ p.
6-3 1. Improving Image Quality The copy appears uneven or at a tilt. 1139O168 Action Wipe the Original Pad clean with a soft cloth. ☞ p. 7-4 The selected paper size is larger Specify a paper size that is than the original document (zoom appropriate to the original document. ☞ p. 3-6 ratio is set to full size 100%) Place the original document The original document is not placed in the proper orientation correctly on the Original Glass. on the Original Glass (zoom ratio ☞ p.
6-4 2. Correcting Functional Problems Symptom Nothing is displayed on the Control Panel. Nothing happens when the Start Key is pressed. The machine will not turn ON. The green light of Start Key will not turn OFF immediately. Check for: Does the green light in the Start Key turn on? Actions The Sleep Function has been enabled. Press the Start Key to disable this mode. Has an Error or Trouble Indicator Follow the procedures provided. become lit? ☞ p.
7-1 Chapter 7 Miscellaneous Chapter 7 Miscellaneous
7-2 1.
7-3 1. Specifications Automatic Document Feeder Original Documents Plain Paper (50–110 g/m2) Original Sizes A4 R–A5 R Capacity Up to 50 sheets Dimensions Width 552 mm × Depth 397 mm × Height 161 mm Weight 4.0 kg Plain Paper (60–90 g/m2) Paper Size A4 R Capacity 500 Sheets Dimensions Width 548 mm × Depth 450 mm × Height 128 mm Weight 5.
7-4 2. Care and Maintenance Cleaning Outer Cover Original Pad Wipe the exterior surface of the machine clean with a soft cloth. 1 2 Open the Original Cover. Wipe the surface of the Original Pad clean with a soft cloth dampened with a mild home detergent. C4007O128CA Original Glass 1 2 Open the Original Cover. C4007O130CA Wipe the surface of the Original Glass clean with a soft cloth. C4007O129CA Control Panel Turn the main power switch OFF.
7-5 3.
7-6 Miscellaneous Chapter 7 3.
A-1 Appendix Index Appendix Index
A-2 Index Numerics O 2 in 1 Copying pp. 3-16, 3-17, 3-18 OHP pp. 3-5, 3-7 Options p. 2-3 A Add toner pp. 5-4, 5-5 Adding paper pp. 5-6, 5-7 Auto Exposure Level Priority pp. 4-4, 4-5 Auto Exposure Mode Key pp. 2-6, 3-14 Auto Panel Reset Function pp. 2-9, 4-4 Automatic Document Feeder p. 3-4 C Caution Labels p. 1-3 Changing exposure levels p. 3-3 Changing zoom ratios p. 3-2 Changing paper trays p. 3-2 Cleaning p. 7-4 Clearing paper misfeeds pp. 5-8, 5-9, 5-10, 5-11 Counters p. 4-2 D Density pp.
