Dash Cam Install Guide
What’s Included? LogiCam Camera Hardware Kit Mounting Bracket Proprietary Screwdriver 2
LogiCam Features Road-Facing Camera Mounting Bracket Slot 1080 P HD Adjustable 140 Angle Camera Lens Tamper Resistant Cover for SIM and SD Card Slots Driver-Facing Camera 720 P HD adjustable wide angle camera IR for Clear Night Vision Power and Auxiliary Inputs with locking screws SOS Button Rotating and Touch Screen Locking Rings 3
Install My20 LogiCam Before you start the install, make sure that the vehicle is parked on a level surface and that the windshield is clean and dry. • Unscrew the safety screw that lock the tamper proof cause using the specialty screwdriver. • Insert the SIM and SD cards. • Attach the mounting bracket onto the camera. • Place the camera as high as possible on the driver side of the vehicle. • Remove the 3M adhesive tape cover, and mount the camera to the windshield.
Adjusting the Angles • Dismount the LogiCam camera from the mounting bracket on the windshield. Make sure that the mounting bracket is not attached, as it locks the camera into position. • Use the screwdriver to loosen the three security screws on the round side of the camera. Do not remove the screws fully. • Adjust the viewing angle by rotating the body of the LogiCam and lock the three side screws when finished. Screws Power jack • • • • Mount the camera back onto the windshield.
Adjusting the Angles • On the main screen enter the “Live View” mode. • Use the “Live View” to direct the road facing camera and the cabin facing camera to the proper direction. You can use the arrow keys to switch between the views. • Dismount the camera from the windshield and screw in the security screws all the way. Mount the camera back on the windshield.
Connect to a Power Source • The LogiCam may only be connected to a power source using the supplied cables. • The camera’s cylinder side is where the input power connector is located. • In order to utilize the LogiCam full features such as active standby, the camera must be connected to a constant 12v power source. Power source Access the Settings Menu • Press the camera touchscreen. • Enter the default PIN number 3333. • The camera is now unlocked and the Settings menu is now accessible.
Calibrating the LogiCam Sensors The LogiCam contains an internal accelerometer that detects unsafe driving events. The accelerometer is not calibrated in advance as the installation in every vehicle is different. Please follow the following steps to calibrate the accelerometer. Before you start, make sure that the vehicle is parked on a level surface. • • • • • Turn on the vehicle’s ignition. Check that the camera is on. Press the touchscreen and enter the security PIN. Enter into the “Settings” menu.
View Live Video • Enter the “Live View” mode in the main menu. • The live video will be displayed on the screen. • Use the arrow keys below the screen to switch between the road and cabin facing cameras. • Use the arrow back button to return to the main menu.
View Recorded Videos • Enter the “Recordings” mode in the main menu. • All the recorded videos on the SD card will be displayed in a list, sorted by date and time. • Use the arrow buttons to scroll through the list. • Select the video you would like to view and then click the “Play” button. Driving Alerts • A white vehicle icon will be displayed on the screen while driving.
Hardwire Your Camera Hardwiring a dash cam is one of the most common installation methods to power on your dash cam. In order to utilize the LogiCam full features such as active standby, the camera must be connected to a constant 12v power source. NOTE: The hardwiring kit includes 2 wires; one RED wire that connects to a constant 12v sources and a BLACK ground wire that will go to a metal ground bolt.
Hardwire to the Vehicle Fusebox Step 1: Locate Your Fuse Box Check the car owner’s manual for the fuse box location. It may vary depending on the vehicle model. Remove the plastic panel to access the fuse box. It may open simply by lifting a tab or pulling it with your fingers, or use a flat tool that can pinch in between the plastics. Step 2: Which Slot Should I Use? Use a circuit tester to test which fuse is constant (typically red) and provides 12v of power.
Hardwire to the Vehicle Fusebox 1. Insert the new fuse tap provided in the kit into “slot 1”, and the fuse from the fuse box into “slot 2” (12v constant or ignition switch). If you set them with the wrong order, it will not feed power to the hardware kit. 1 New Fuse Tape Add a Fuse Kit 2. Connect the hardwiring cable with the terminal crimp connector from the add-a-fuse kit. Trim off some of the rubber tubing to expose the wiring on your hardwiring cable. Then crimp them down together.
Hardwire to the Vehicle Fusebox 3. Connect you add-a-fuse kit to the vehicle fuse slot that you have chosen. Step 4: Ground the Hardwire Kit 4. The ground wire is usually in a C shape or a ring. To connect the ground wire, slip it under a metal bolt or screw in your vehicle. 5. You may need a socket wrench set to loosen the bolt. Loosen the bolt enough to slip it in and tighten it back up afterwards. A loose ground can result in power issues for your dash cam.
