Installation Sheet

Canopy Installation
OFF
ON
Your circuit
breaker may
look
different.
Shock Hazard. Electric shock could result in serious injury or death. Make sure circuit
breaker is set to OFF before installaon. Must be installed by a qualified electrician.
1
pendant light
Z-BAR
rise square
rise square rise square
rise square
Canopy Installation
2
pendant light
Z-BAR
Feed the wires through the cable
grippers, then screw in cable
grippers to the holders.
Use the
provided strings
to hang the
cover plate
from the
canopy during
installaon.
-
+
-
+
-
+
-
+
-
+
Aer step 2 is finished and no
more adjustments are needed,
remove the hanging strings and
secure the cover plate by fing
the two screws from the sides.
Pull the core wire out
and fit it into the +
posive terminal. Twist
the skin of the wire and
fit it into the - negave
terminal. There are 2
power wires for the 16“
and 24” versions, and
4 power wires for the
48” version of this
pendant.
-
+
Aach LED light bars to the joints as illustrated below.
Make sure they are fully inserted with no gaps.
Your pendant is ready for use. Enjoy!
Feed the AC power cords from the LED
drivers into the juncon box through
the hole then connect them to the live
and neutral wires from the juncon
box accordingly. Connect the ground
wire from the canopy to the juncon
box’s ground. Make sure the canopy is
centered and fully covering the
juncon box.
If your canopy contains more than 1
LED driver, connect all white (neutral)
wires together to Neutral using a
twist-on connector, and all black (live)
wires to Live using a twist-on
connector. Do not mix neutral and live
wires.
Oponal: For extra reinforcement,
secure the canopy to the juncon box
using the 4 provided screws and
drywall anchors.
Boom view of canopy for 16” and 24” Z-Bar Pendant Rise Square
Boom View of canopy for 48” Z-Bar Pendant Rise Square
Wires can be released and
re-adjusted by pressing the cable
grippers’ “nozzle”. All wires
should be of equal length.
Canopy Installation
pendant light
Z-BAR
Canopy Installation
pendant light
Z-BAR
Overheang may result in reduced LED lifespan:
• Keep out of direct sunlight.
• Remove plasc bag from lamp before use.
• Recommended ambient temperature: under 77 °F.
Koncept Inc.
429 E. Huntington Drive
Monrovia, CA 91016, USA
Phone: [phone]
Fax: [phone]
Customer Support:
[e-mail]
Warning: To reduce the risk of fire, electric shock or injury:
• Do not use in wet locaons
• Do not handle plug or appliance with wet hands
• Do not stare directly at LEDs
Web Address:
www.koncept.com
Specificaons
Register your Koncept LED lamp online and receive:
• One Year Warranty Extension
• Priority Product Servicing
Visit www.koncept.com/productsupport and enter your
serial number (S/N: XXXXXXXX) located on your product.
Model ZBP-RS
Color Temperature 3000 K
Light Color So Warm
Brightness Adjustability
Compable w/ELV or LED dimmers
Input voltage 120V only
3
4
Koncept warrants to the original purchaser of this product against manufacturer defects in design, assembly, material, or workmanship,
and will, at Koncept’s opon, replace or repair any defecve product free of charge. This coverage is valid for five years from the date of
purchase as long as the original purchaser owns the product. In the case of a hardwired product, this warranty is valid for one year for
the LED driver specifically. Koncept will replace or repair the product, which Koncept, at its sole discreon, agrees is defecve, free of
charge provided that the following condions for a return are fulfilled.
This warranty does not apply to any product damaged by accident, physical or electrical misuse or abuse, improper installaon,
alteraon, any use contrary to its intended funcon, war, fire, flood, or any other acts of nature, or unauthorized repair. This warranty
does not apply to the LED driver in the case of a hardwired product. This warranty does not apply to a product purchased from an
authorized 3rd party dealer.
Koncept assumes no liability for any events such as fines arising out of the use of this product or any consequenal damages caused by
any failure of the product to funcon properly. In no event shall Koncept be liable for more than the replacement of the product. This
warranty does not cover shipping or labor costs associated with the replacement of a defecve product. Under no circumstances should
this warranty or the product covered by it be construed as an insurance policy against loss of any kind. Koncept staff neither assumes
nor authorizes any person or organizaon to make any warranes or assume any liability in connecon with the sale or use of this
product.
This warranty covers only products used in the territory covered by your local distributor. This is the complete product warranty and no
other warranty exists. Some jurisdicons may not allow limitaons on how long an implied warranty lasts, or the exclusion or limitaon
of incidental or consequenal damages, so the above exclusions or limitaons may not apply to you. This warranty gives you specific
legal rights, and you may also have other rights which vary in different states and countries.
To file a replacement/repair claim under the warranty:
1) Contact Koncept for a return authorizaon number during the warranty period. A claim will not be accepted without a return
authorizaon number.
2) Provide a copy of the original purchase receipt with purchase date and product name clearly shown.
3) Return the defecve product to Koncept, freight prepaid, accompanied by (1) and (2) to the following address: Limited Product
Warranty
Koncept Inc.
429 E. Hunngton Drive,
Monrovia, CA 91016
Limited Product Warranty
v.01092019