Installation Sheet

Installation Guide SKU#22659
USA/Canada: 1-800-4 KOHLER 1391088_2
www.kohler.com
Approved fastener
(Wire nut)
Electrical tape
PREPARATION
1. Record your model number for future reference.
2. DANGER: Risk of electric shock. To avoid electric shock, the power must be turned off at the circuit breaker or fuse box before beginning
the installation procedure.
3. DANGER: Risk of electric shock. To avoid electric shock, the outlet box must be properly grounded.
4. Important Information. Inspect the product for any damages. This product is for indoor use only. Observe all local codes.
5. Your product may appear different than the one illustrated. The installation procedures remain the same.
Please see next page for a larger installation image
TOOLS AND MATERIALS NEEDED
FIXTURE INSTALLATION
1. Remove the fixture and parts bag(s) from the carton. Put them onto a clean and soft
cloth to protect finish. Confirm all parts are included.
2. To adjust the length of cords, loosen the set screw (H) on the canopy (C) until the
cords can slide. Be careful not to remove the set screws. Adjust the length of cords
by pulling cords through the canopy (C) to set fixture at desired height. Then tighten
set screws (H); be careful not to pierce wiring.
3. Slide safety clip (I) down cord to touch canopy. Do not damage the cord insulation
layer.
4. Cut excess cord to minimum 6” beyond canopy (C).
a) Trim cloth 2” from the end.
b) Strip insulation 5/8” from end of wire without cutting copper wire.
c) Twist each copper wire individually.
5. Mark the anchor hole position (L) or (K), take down the mounting plate. Then, drill
the anchor hole in Dia. 1/4” for concrete ceiling or Dia. 3/8” for drywall ceiling.
6. Insert anchor (K) or (L) into ceiling. Attach the mounting plate (B) onto the outlet box
with screws (N) and drywall screws (J) to ceiling anchors. Ensure the direction of
ground screw (O) and mounting screws (M) are as shown.
7. Lace safety cord (P) around mounting plate, secure it on mounting plate with its lock.
8. NOTICE: To avoid short circuit, make sure wires are not exposed. Gang together three
black wires from fixture and one black wire from the quick connect into a wire nut
(A). Wrap the wire connector with electrical tape so that the tape seals the end of
wire nut (A). Then repeat the step for the white wires from fixture and white wire
from quick connect; repeat the step for the green wires from fixture and green wire
from quick connect. See diagram.
9. NOTICE:
To avoid short circuit, make sure wires are not exposed. Using the other
quick connect piece, connect black wire from outlet box and black wire from the
connect piece in a wire nut (A). Wrap the wire connector with electrical tape so that
the tape seals the end of wire nut (A). Then repeat the step for the white wires
from outlet box and white wire from quick connect; repeat the step for the green
wires from outlet box and green wire from quick connect. See diagram.
10. Press together the two connectors (R).
11. Tuck wires carefully inside outlet box. Align screws (M) on mounting plate (B) with
holes on canopy (C), then secure the canopy (C) onto mounting plate (B) with nuts (G).
12. NOTICE: Do not exceed recommended wattage. Install lamp(s). Rated Max 40 W, Type B. (Bulb(s) not included).
13. Install the small glass shades (E) and medium-sized glasses (F) onto glass holders with screws (D).
14. Restore power to circuit at breaker or fuse box.
CLEANING
Please clean fixture with a soft and dry cloth ONLY. Clean glass with a mild soap.
F
E
C
D
A
B
J
K
N
I
O
G
L
H
M
P
R
Phillips &
Flathead
Screwdriver
Slip Joint
Pliers
Small
Adjustable
Wrench
Wire
Cutter/stripper
Electrical
Current
Tester
Electrical
Tape
Allen Wrench