BEVERAGE COOLER 43L, 93L KAM43BEVFGA, KAM93BEVFGA
SAFETY & WARNINGS Ensure to read all instructions and warnings in this user guide prior to first use. Retain this user guide for future reference. • This beverage cooler is intended to be used in household and non-commercial use (for example, staff kitchens, offices, hotel rooms). • The temperature range of this beverage cooler is 5–14°C.
• WARNING: If a previous beverage cooler is being replaced, ensure to remove the doors, and leave the shelves in place to prevent children from entering the appliance. • The refrigerant and cyclopentane foaming material used in this beverage cooler is flammable. Keep all heat sources (for example, stoves, radiators) away from the beverage cooler. • When positioning the beverage cooler, ensure the power cord is not trapped underneath the beverage cooler or at risk of being damaged.
OVERVIEW 43L Beverage Cooler Door handle Glass shelf Thermostat knob Levelling foot 93L Beverage Cooler LED light Door handle Steel wire protective cover Thermostat knob Levelling foot Note: Images used in this user guide are for reference only.
BEFORE FIRST USE • Remove all packaging and tape from inside the beverage cooler. Remove the protective film on the door and beverage cooler body. • Wipe the interior of the beverage cooler to clean any dust and other particles. Reversing the door swing ASSEMBLY If you would like to change the direction of the swing for the door (right swing to left swing), follow the steps outlined below. 1. Ensure the door is closed and the beverage cooler is unplugged.
3. Loosen the door axle sleeve (6) located on the bottom right of the door, door stopper (7) and block screws (8) then secure the components (6, 7, 8) to the left side. 8 7 6 4. Loosen the adjustable foot (10), position bolts (4), and lower hinge (9), then install the components (4, 9, 10) in the reverse order on the left side of the beverage cooler body. 9 4 10 5. Align the door onto the repositioned lower hinge (9) and secure the door to the upper hinge (5).
OPERATION 1. Place the beverage cooler on a stable flat surface in a well-ventilated area. Ensure there is at least a 30cm clearance above, and at least a 10cm clearance on the sides of the beverage cooler. Rotate the levelling feet if the beverage cooler is unstable. 30cm 10cm 10cm 2. Plug the power cord of the beverage cooler into a socket. When plugged in for the first time, wait for 30 minutes to allow the beverage cooler to cool.
3. Open the door and place the beverages into the cooler. The number of bottles that can fit into the cooler will vary depending on their size. Notes: • Do not allow bottles to touch the back of the beverage cooler as this can restrict the circulation of cool air. • The temperature of the lower shelves in the beverage cooler and colder than the upper shelves. • Try to minimise the amount of time the beverage cooler’s door is left open.
CLEANING & CARE The beverage cooler should be cleaned regularly. Ensure the beverage cooler is set to the OFF temperature mode or is unplugged before cleaning. Interior The interior of the cellar should be cleaned regularly to avoid odour. • Remove any drinks and shelves inside the beverage cooler. • Combine two tablespoons of baking soda with one litre of warm water. Using this solution, clean the interior with a soft cloth or sponge.
TROUBLESHOOTING Problem Reason/solution Low voltage Ensure the cellar is plugged in and connected to power. No power Ensure the temperature knob is not turned to the OFF mode. Illuminating light does not shine • Ensure the beverage cooler is connected to power. • Check if the light is damaged. If so, stop use and contact help.Kogan.com for assistance. The compressor is running longer than usual.
Need more information? We hope that this user guide has given you the assistance needed for a simple set-up. For the most up-to-date guide for your product, as well as any additional assistance you may require, head online to help.kogan.
