ACTIVE PRO GPS ALWAYS-ON DISPLAY SMART WATCH KATPROGPSWA
SAFETY & WARNINGS Battery warning Do not disassemble, pierce or damage the battery. Do not disassemble the built-in batteries of non-replaceable battery devices. Do not use sharp objects to remove the battery. Health Warning If you are wearing a pacemaker or other implanted electronic devices, consult your doctor before using the heart rate monitoring strap. The watch’s optical heart rate sensor glows green and flashes.
APP INSTALLATION 1. Turn On The unit will automatically turn on after charging. Note: The Watch must be charged and activated before the first use. Use only the original power adapter to charge the watch. Turn on by pressing and holding DOWN button.
2. Download and Install VeryFitPro You can directly scan the QR code to download VeryFitPro or search “VeryFitPro” in the APP store to download and install. Note: The hardware requirements for connecting to a smart device are shown below. iOS 9.0 and above Android 4.4 and above 3. Connect to mobile phone correctly. Bluetooth 4.
4. Bind the Device Go to the App home page to show the binding request. Select the product model and tap “Confirm Binding” to complete binding.
OPERATION Up button Screen Down button 1.
2. Operation on Screen Select to enter the next interface/select current item. Tap Screen Tap and hold Tap and hold in the main dial interface to enter dial switching interface. Slide left/right Switch interfaces left and right. Slide up/down Switch interfaces up and down. 3. Operation of Gestures Raise to turn on backlight. Hang to turn off backlight. Note: Activation of this function can be set up through mobile APP.
Sports Function 1. Activate Sports Enter Sports list interface, slide up or down to select sports item and tap icon to start sports. 2. Start Sports When Outdoor Running is activated, the Watch will scan for GPS signals automatically. You can tap Skip Icon to skip GPS positioning, but motion trail cannot be displayed prior to successful positioning. Count-down starts after successful positioning or after skipping positioning. Start sports after count-down is over. 3.
4. Reminders during Sports During sports, the Watch will continuously detect your current heart rate. If the current heart rate exceeds the maximum heart rate, the Watch will remind you to reduce sports intensity or stop sports through vibration and interface alarm. Set your safe heart rate reminder through More>Heart rate zone>User defined Maximum Heart rate is in the mobile APP. 5. Pause or Stop Sports Pause sports: In the unlocked state, press and hold “UP” button to pause sports.
2. Notifications Turn on smart reminder Enable “Smart Reminder” in the APP, then select and enable notification types to be reminded. This function requires a constant Bluetooth connection between the Watch and mobile phone. View message When receiving s message, the Watch will vibrate to alert you. If the message is not immediately viewed after being received, slide down to view the message. Delete message The Watch can save the most recent 12 notifications.
4. Blood Oxygen The Watch supports blood oxygen detection. Slide to Blood Oxygen Detection interface, hold for two seconds, and the Watch will automatically detect blood oxygen levels. Stand still and keep your arm steady during the detection so that the Watch can output more accurate blood oxygen data. Note: To improve the accuracy of blood oxygen detection, wear the Watch correctly and keep parts that contact the skin clean. Blood oxygen detection can take some time; be patient. 5.
Timer Allows setting a countdown timer. The watch will vibrate once this time has elapsed. Alarm clock You can set alarm clocks from the mobile APP. When it is the set time, the Watch will alert you through vibration. In the case of no operation after 20 seconds, the alarm clock will automatically stop. After 5 minutes, the alarm clock will then vibrate again. Press UP/DOWN button to engage the Snooze function, and after 5 minutes the alarm clock will alert you again. Slide up to turn off alarm reminder.
CLEANING & CARE Replace watch strap Use a soft brush or clean soft cloth to clean the Watch. Remove the Watch from your wrist and disconnect all connections with other equipment before cleaning and maintenance. Keep the Watch and its accessories dry. Do not dry them with external heating equipment such as a microwave oven or hair dryer. Do not place the Watch or its accessories in an area where the temperature is excessively high or low, as this may cause malfunction, fire or explosion.
TROUBLESHOOTING Problem Solution 1. It is recommended to update VeryFitPro to the latest version. Mobile phone cannot be connected to the Watch. 2. It is recommended to quit all APPs, reactivate the phone Bluetooth and reconnect. 3. Confirm that the system of the phone is Android 4.4 or iOS 9.0 and above. The Watch has no message or call reminders. 1. The smart reminder function and call reminder function must be enabled in the APP and synchronised to the Watch. 2.
Need more information? This is a Quick Start Guide, and we hope that this has given you the assistance needed for a simple set-up. For the most up-to-date guide for your product, as well as any additional assistance you may require, head online to help.kogan.
