User manual

ManualsBrandsKodak ManualsDigital CamerasPixPro FZ-152

Table Of Contents

User Manual

Summary of content (90 pages)

PAGE 1
User Manual
PAGE 2
Before You Start Declaration of Conformity Responsible Party: JK Imaging Ltd. Address: JK Imaging Ltd., 17239 South Main Street, Gardena, CA 90248, USA JK Imaging Europe, 71 Clarendon road, Watford, WD17 1DS, UK Company website: www.kodakpixpro.com For Customers in the U.S.A. Tested to Comply with FCC Standards FOR HOME OR OFFICE USE This device complies with part 15 of the FCC Rules.
PAGE 3
About this Manual Thank you for purchasing this KODAK PIXPRO digital camera. Please read this manual carefully and keep it in a safe place for future reference. JK Imaging Ltd. reserves all rights of this document. No part of this published manual may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form, by any means, without the prior written permission of JK Imaging Ltd..
PAGE 4
Safety Notes Safety notes for this camera Do not drop the camera or allow it to hit solid objects. Do not attempt to disassemble or repair the camera. Do not use or store the camera in dusty places or on a beach to prevent dust or sand from entering the camera, causing possible damage to it. Do not use or store the camera in a hot environment or under direct sunlight. Do not use or store the camera near a powerful magnetic field, for example near a magnet or transformer.
PAGE 5
Safety notes for battery Please use a battery that is the same type as the one included. Please use the attached charger to charge the battery. If battery fluid leaks inside the camera, contact our customer service department. If battery fluid leaks onto your skin, rinse your skin with clean water and seek immediate medical attention. Disposal of used batteries should be carried out in accordance with the local (national or regional) regulations.
PAGE 6
Safety notes for memory card We suggest buying only well-known, name brand memory cards to ensure peak performance. Format the memory card using the camera before you use it or insert a new one. Do not drop the memory card or allow it to hit solid objects to avoid damaging it. Do not attempt to disassemble or repair the memory card. Do not expose the memory card to water. Always keep it dry. Do not remove the memory card when the camera is turned on. Otherwise, the memory card could be damaged.
PAGE 7
Other Safety Notes Do not disconnect the power or turn the camera off during the update process. Doing so may cause incorrect data to be written and the camera may not power on later. When using your camera on an airplane, observe the relevant rules specified by the airline. Due to the limitations of manufacturing technology, the LCD may have a few dead or bright pixels. These pixels do no effect the quality or performance of the camera, photos or video. Do not expose the LCD to water.
PAGE 8
Contents Before You Start ��1 Safety Notes �� 3 Contents �� 7 Getting Ready �� 11 Accessories
PAGE 9
Overview of the Screen Icons in Movie Mode �� 22 Using the Mode Button �� 23 Panorama Mode ��24 Scene Mode ��
PAGE 10
Slideshow ��41 Photos and Video Deletion ��42 Using the Menus ��43 Shooting Menu ��
PAGE 11
File Setting ��66 Format ��66 Copy to Card �� 67 File Numbering ��
PAGE 12
Getting Ready Accessories Included Your camera box should contain the camera model you purchased along with the following accessories. If anything is missing or appears to be damaged, please contact your retailer. (Based on sales in different countries or regions, the shape of the AC adapter will vary. Please subject to the actual product will prevail.
PAGE 13
Part Names 2 3 4 5 6 1. Micro USB port 2. Zoom lever 3. Shutter button 4. Power button 5. AF assist beam/Self-timer lamp 6. Flash lamp 7. Lens 1 8.
PAGE 14
9. Indicator lamp 9 10. Fast video recording button 11. Mode button 12. A 10 C Display button/Arrow button (Up) 13. A C Flash button/Arrow button (Right) 11 12 13 14 14. SET button 15. Playback button 16. Battery cover 17. A C Delete button/Arrow button (Down) 15 18. Menu button 16 19. A CM acro button/Self-timer button/ Arrow button (Left) 22 21 20 19 18 17 20. Tripod socket 21. Speaker 22.
PAGE 15
Installing Battery and Memory Card 1. Open the battery cover. 2 1 14 2. Insert the battery into the battery compartment according to the negative and positive directions as illustrated in the picture. Push the battery down until it locks in place.
PAGE 16
3. Insert the memory card into the memory card slot as shown in the diagram below: 4. Close the battery cover. 1 Write protection buckle 2 The memory card (SD/SDHC) is optional and not included in all camera packaging. It needs to be purchased separately. Please use an original memory card which is Class 4 or higher and has a capacity of 4GB to 32GB. To remove your memory card, open the battery cover, gently press the memory card to eject it and remove it carefully.
PAGE 17
Charging Battery Indicator lamp Please insert the battery and charge it under shutdown mode. 1. Connect the camera and the power charger using the supplied Micro USB cable. 2. Insert the plug of the power charger into the power outlet to charge the battery. 3. When the camera is turned off, you can also connect the camera to your PC using a Micro USB cable to charge the battery. After the battery is stored for a long period of time, use the supplied power charger to charge the battery prior to use.
PAGE 18
Turning Camera On and Off Press the power button to turn the camera on. To turn the camera off, press the power button again. Power Button How to take pictures 1. Hold the camera with both hands , not blocking the flash and lens by fingers. 2. Aim the camera at the object and then frame with the LCD. 3. Use the zoom lever to select Tele or Wide positions to zoom in or out on your subject. 4. Press the shutter button half way to focus on the subject.
PAGE 19
Set your Language, Date/Time Set your Language, Date/Time after the first power-on 1. When you turn the camera on for the first time, the language selection screen appears. 2. Press the direction buttons to select your desired language. 3. After you press the button to confirm the selection, the Date/Time settings screen appears. 4. Press the left/right button to select the Date/Time to be adjusted: Time is displayed in YYYY.MM.DD HH:MM. 5.
PAGE 20
Resetting your Language After you set your language for the first time, follow the instructions below to reset your language. 1. Press the button, press the up/down button to select , and press the button to enter the menu. 2. Press the up/down button to select , and press the button or right button to enter the menu. 3. Press the up/down button to select「Language」and press the button or right button to enter the menu. 4.
PAGE 21
Resetting Date/Time After you set your Date/Time for the first time, follow the instructions below to reset date and time. 1. Press the button, press the up/down button to select , and press the button to enter the menu. 2. Press the up/down button to select , and press the button or right button to enter the menu. 3. Press the up/down button to select「Date & Time」and press the button or right button to enter the menu. 4.
PAGE 22
Mode Overview LCD Screen Display Overview of the Screen Icons in Photo Shooting Mode 1 2 3 4 5 SD x3.2 23 22 21 20 19 18 6 7 8 1234 17 00:56:00 15 sec 16 -0.
PAGE 23
Overview of the Screen Icons in Movie Mode 1 2 3 4 5 6 SD x3.2 15 7 14 13 12 00:56:00 8 -0.
PAGE 24
Using the Mode Button This camera provides a convenient mode button that allows you to switch easily among different modes. After pressing the button to enter the mode selection menu, press the left/right button to choose the selected mode. Press the button to confirm your selection. All the available modes are listed below: Mode Name Icon Description Auto Mode In this mode, the optimal conditions for taking pictures will be set based on the subject and environment.
PAGE 25
Panorama Mode Panorama Mode allows you to create a panoramic picture. The camera will automatically compose a panoramic picture using the individual shots that you take. Follow these easy steps to create a panoramic picture: 1. Press the button to select panorama mode ( ). 2. Press the direction buttons to select a shooting direction. (The right direction is used as default if you do not make any choice) 2 seconds later, the camera is ready to take pictures.
PAGE 26
Scene Mode During shooting, the flash, selftimer, macro modes and exposure compensation are not available. Focus adjustment is also not available at this time. In Panorama Mode, up to 4 photos can be captured when the image size is set at 2M. You can select an appropriate mode from the 20 scene modes according to the type of environment you are shooting. The camera then configures the most appropriate settings automatically. 1. Press the button to select scene mode ( ).
PAGE 27
Scene Auto Scene Landscape Sport Beach For taking pictures in areas with strong sunlight. Sunset For sunsets. Capture subjects in strong sunlight. Fireworks For fireworks at night. Slower shutter speed is adjusted for brilliant images. The use of a tripod is recommended. Night Landscape For night scenes. The use of tripod is recommended. Snow For snow scenes. Reproduce natural, clear white scenes.
PAGE 28
Scene Panning Shot Description Suitable for capturing fast moving objects to have a clear subject with a blurred background. Fish Eye For interesting fish eye effect. Party Suitable for taking indoor party pictures, even under the complicated lighting conditions. Indoor For indoor settings. Reduce blur and improve color accuracy. Leaf For plants. Capture brilliant shots of greenery and blossoms. Museum For museums or flash-free areas. Retain color and reduce blur.
PAGE 29
Auto Scene Mode (ASCN) In “ASCN” scene mode, the camera can detect different environments intelligently and automatically select the best scene and photo settings for you. “ASCN” can intelligently detect the following scenes: Mode Name 28 Description Landscape Mode For landscapes, will automatically adjust the exposure and reproduce vivid green and blue colors. Portrait Mode Most suitable for capturing people with focus on their faces.
PAGE 30
Basic Operation Using the Zoom Function Your camera is equipped with two types of zoom functions: optical zoom and digital zoom. Toggle the zoom lever of the camera to zoom in or out of the subject while taking pictures. Zoom Out Zoom Lever Zoom Indicator Zoom In When the optical zoom reaches the threshold as digital zoom, release and turn the zoom lever to T to switch between the optical zoom and digital zoom.
PAGE 31
Display Setting Press the button to display the settings: Classic, Full, Off. Classic: D isplays the camera parameters on Off: Does not display any additional icons on screen screen SD 1234 16M 00:56:00 -0.3 EV 400 ISO Full: C amera parameters with Grid and Histogram SD 1234 16M 00:56:00 -0.
PAGE 32
Macro Mode The Macro setting is ideal for shooting small objects or close-up photos. This mode allows you to focus on subjects very close to the camera. 1. Press the left button ( marco menu. ) to enter the • Macro Off Select this option to disable macro. • Macro On Select this option to make focusing on the object closer to the lens (At the W side, the shooting distance should be more than 3 cm). 3. Press the button to confirm the settings and enter the shooting screen. 2.
PAGE 33
Self-timer Setting Use this function to take pictures at pre-set intervals. First choose 2 seconds, 10 seconds,or by smile detection. and then take the pictures. • 1. Press the left button ( press the down button ( self-timer menu. Self-timer 10 sec A single picture is shot 10 seconds after the shutter button is pressed. • Self-timer Smile Press the shutter button and a picture will be taken immediately after a smile is detected. ) , and then ) to enter the 3.
PAGE 34
Flash Mode The flash provides supplemental light for the scene. The flash is usually used when shooting against the light to highlight the object; it is also suitable for metering and shooting in darker scenes to improve the exposure. 1. Pop up the flash manually as shown below (as shown in the figure). 2. Press the right button ( flash settings menu. ) to enter the 3. Press the left/right button to select the following 6 modes: • Force Off Flash is turned off.
PAGE 35
EV Setting The EV function menu of the camera includes functions, such as EV, shutter adjustment, ISO. Using the appropriate function settings can improve your pictures. To select the best setting for optimum photos, follow these steps: 1. Press the screen. Exposure Compensation Set up to adjust the picture brightness. In the case of a very high contrast between the photographed object and the background, the brightness of the picture can be appropriately adjusted.
PAGE 36
ISO Shutter Adjustment The ISO function allows you to set the sensitivity of the camera's light sensor based on the brightness of the scene. To improve the camera's sensor performance in darker environments, a higher ISO value is required. A lower ISO value is needed when shooting in brighter conditions. For shutter speed, the camera may automatically set the aperture value corresponding to the manually set shutter speed so as to obtain a most suitable exposure value.
PAGE 37
Using Quick Recording In shooting mode, press the button to begin recording video. After recording, press the button or the shutter button to stop recording. The camera will store the video and return to the shooting screen.
PAGE 38
Playback Mode Overview of the Screen Icons in Playback Mode 1 2 3 1/45 SD 4 5 12 11 10 6 x2 2015 06-25 00:00 7 8 9 1 DPOF File 7 Image Zoom Ratios 2 File Protection Memory space (indicating the current number of photos and total number of photos) Memory Card/Built-in Memory Battery Status Zoom Magnification Area 8 Image Zone 9 Shooting Date 10 11 12 Eye-Fi ON (with signal) Red-Eye Reduction HDR 3 4 5 6 37
PAGE 39
Viewing Photos and Videos To view the captured photos and video clips on the LCD: 1. After pressing the button, the last photo or video clip taken will be displayed on the LCD. 2. Use the left/right navigation buttons to scroll through the photos or video clips stored in the internal memory or on the memory card. 3. To play a selected video clip, press the button to enter the movie playback mode. An operation guide appears on the screen when playing back a video.
PAGE 40
Thumbnail View When in playback mode, rotate the zoom lever counter to the position to display thumbnail images of the photos and videos on the screen. W 2. Press the direction buttons to select a picture or video clip to view and press the button to restore it to the original size. When the icon is a video file. appears, it means this 1. Slide the zoom lever to switch between 3x3 and 4x4 thumbnails.
PAGE 41
Using Zoom Playback (for still pictures only) When playing back photos, you can also use the zoom lever to zoom in on the photos 2 to 8 times. 1. Press the button to switch to playback mode. 2. Press the left/right button to select a picture to be zoomed in. 3. Rotate the zoom lever to to zoom in. T Zoom In x2 x2 4. The screen will display the number of times and area of the photo zooming operation. 5. Press the direction buttons to navigate and select a part of the image to be zoomed in. 6.
PAGE 42
Slideshow This setting allows you to view all the stored images as a slideshow. 1. Press the button to enter playback screen. 2. Press the button to enter slide option. 3. Press the left/right button to select slideshow playing or 「Cancel」 to return to the playback screen. 4. Press the button to confirm the setting. Slide playing function supports movie playing. Images don’t rotate in the slideshow playback.
PAGE 43
Photos and Video Deletion In playback mode, press the down button ( to delete your photos and videos. To delete photos or videos: 1. Press the mode. button to switch to playback 2. Press the left/right button to select the photos and videos to be deleted. 3. Press the down button ( ) and the deletion screen is displayed. 42 ) 4. Press the up/down button to select「Delete One」or「Exit」and press the button to confirm. Erased photos/video clips cannot be recovered.
PAGE 44
Using the Menus Shooting Menu Functions that can be enabled are different under each mode. Mode: Expo Metering Use this setting to select the "target" size of the camera's field of view to be metered. 1. In photo shooting mode, press the button to enter the shooting menu. 2. Press the up/down button to select the shooting menu to be set. 3. Press the left/right button to select the shooting menu to be set and press the button to confirm. Refer to the following pages for more details about each setting.
PAGE 45
Image Size OIS (Optical Image Stabilization) The size setting refers to the image resolution in pixels. A higher image resolution allows you to print that image in larger sizes without degrading the image quality. This mode can help reduce photo blur caused by unintentional hand shake, low light. The larger the number of recorded pixels, the larger the file size and the fewer files that can be saved on your memory card. • OIS: Off • OIS: On Use this image stabilization mode in dark environments.
PAGE 46
White Balance Setting Cont. AF The white balance setting allows you to adjust the color temperature for different lighting sources to ensure the most accurate color reproduction. Enable the continuous AF to be able to continuously focus automatically when taking pictures. • AWB • Cont. AF: Off • Daylight • Cont.
PAGE 47
Focus Setting Continuous Shot In different photo shooting modes, you can select different focus methods. Use this setting to perform continuous shooting. After entering this mode, you can shoot multiple images by continuously holding the shutter button down. • • 46 Single-AF The focus frame appears on the center of the LCD to focus on the subject. Multi-AF The camera automatically focuses the subject in a wide area to find the focus point.
PAGE 48
Color Effect The flash is disabled in the continuous shooting in order to achieve quick succession of shots. The image color setting allows you to select different effects. 1. In photo shooting mode, press the button to enter the shooting menu. 2. Press the up/down button to select the image color setting menu, press the button to enter the menu. 3. Press the left/right button to select the image color setting options.
PAGE 49
• Options in the shooting mode (○: Disponible ×: Indisponible) Shooting Modes Options 48 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ × × ○ ○ ○ × ○ ○ ○ × ○ ○ × × × ○ × × × ○ × × × × × ○
PAGE 50
Shooting Setting Menu Quality Mode: 1. Press the button in photo shooting mode and press the up/down button to select . 2. Press the button to enter the menu. 3. Press the up/down button to select , and press the button or right button to enter the menu. The quality setting can be used to adjust the image compression ratio. • Best (16M Average File Size: 4.0MB) • Fine (16M Average File Size: 2.5MB) • Normal (16M Average File Size: 2.0MB) 4.
PAGE 51
AF Assist Beam Digital Zoom In a darker environment, AF assist beam can be turned on for better focus. This setting is for adjusting digital zoom. If this function is disabled, only optical zoom can be used.
PAGE 52
Date Imprint Quick Review Include a Date/Time stamp on the photo image. This option allows quick review of the photos immediately after they are taken. Each photo is displayed on the LCD based on the selected time.
PAGE 53
Face Detection For detecting and focusing on faces to make all faces as clear as possible in photo mode. 2. Press the shutter button half-way down to focus. The LCD will show a green focus frame when the subject is in focus. F2.9 1. Hold the camera steadily and then focus on the object to detect its face. A focus frame will appear at the face on the screen when a face is detected. 1/50 3. Press the shutter button all the way down to take pictures. The closed eyes detection is usually on.
PAGE 54
Movie Menu Mode: 1. Press the button, select the mode and press the button to enter the movie menu. Expo Metering Use this setting to select the "target" size of the camera's field of view to be metered. 2. Press the up/down button to select the movie menu to be set. 3. Press the left/right button to select the movie menu to be set and press the button to confirm.
PAGE 55
Video Quality Set the image resolution used during video recording. * The longest recording time is 29 minutes at one time. When recording in higher pixel resolutions for extended periods of time, this can cause the camera to generate heat. This is not a camera malfunction. The speed requirements for reading and writing high image pixel images to memory card are as follows: 54 Frame Recommendation Recording time (4GB) About No.
PAGE 56
OIS (Optical Image Stabilization) Color Effect This mode can help reduce images blur caused by unintentional hand shake, low light. The image color setting allows you to select different effects. 1. Press the button to select the Image color setting menu. 2. Press the left/right button to select the image color setting options. • OIS: Off • OIS: On Use this image stabilization mode in dark environments. Shooting in a windy or unstable environment (such as a moving vehicle) may cause blurred images.
PAGE 57
Movie Setting Menu Mode: 1. Press the button, and select the video recording screen. Digital Zoom to enter 2. Press the button, press the up/down button to select , and press the button to enter the menu. 3. Press the up/down button to select , and press the button or right button to enter the menu. 4. Select the items to be set and press the button or the right button to enter the menu. 56 5. Press the up/down buttons to select an option and press the button to confirm.
PAGE 58
Playback Menu Mode: HDR 1. Press the button to display the playback screen and press the button to enter the menu. With the HDR function, pictures that are overexposed may be corrected to optimize the highlights and lowlights captured to more accurately represent the actual scene. 2. Press the up/down button to select the playback to be set and press the button to enter. 3. Press the left/right buttons to select an option and press the button to confirm.
PAGE 59
Red-Eye Reduction Rotate You can use this setting to reduce the Red-Eye of the picture. You can use this setting to change the orientation of the picture. : : Red-Eye Reduction : Cancel Turn Right : Turn Left : Cancel Videos and panoramic pictures cannot be rotated. The rotated picture file will replace the original photo.
PAGE 60
Resize Color Effect This setting allows you to resize a picture to a particular resolution and saves it as a new picture. This setting allows you to change the picture color effect. The file is saved as a new photo and stored in memory together with the original photo. : Resize to 1024x768 : Resize to 640x480 ： Cancel Only for adjusting pictures with high resolution to those with low resolution.
PAGE 61
Playback Setting Menu Mode: 1. Press the button to show the playback screen, press the button, and press the up/down button to select . 4. Press the up/down button to select the item to be set and press the button or right button to enter the menu. 2. Press the 5. Press the up/down buttons to select an option and press the button to confirm. button to enter the menu. Refer to the following pages for more details about each setting. 3.
PAGE 62
Protect Delete To prevent any pictures or videos from being accidentally erased, use this setting to lock one or all of the files. You can delete one or all photo/video files. • One: • All: Lock the selected photo or video if they are unprotected; unlock the selected photo or video if they are protected. Lock all photos or videos. • Reset: Cancel all locked photos or videos. • One: Delete one photo or video. • All: Delete all photos or videos. The “ ” indicator means a file is protected.
PAGE 63
DPOF (Digital Print Order Format) Trim The DPOF feature allows you to compile and select a group of pictures that you would like to print and will save your selection on the memory card so that you can use the memory card to print without having to individually specify the photos you want to print. The Trim Setting allows you to crop photos and save them as new pictures. The printer that supports DPOF is needed for printing. 1. Select「Yes」to confirm trim.
PAGE 64
Setup Menu Mode : 1. Press the button in any mode and press the up/down button to select . 2. Press the button to enter the menu. 3. Press the up/down button to select , and press the button or right button to enter the menu. 4. Press the up/down button to select the item to be set and press the button or right button to enter the menu. 5. Press the up/down buttons to select an option and press the button to confirm. Refer to the following pages for more details about each setting.
PAGE 65
Sound Settings Power Saver With this setting you may adjust the sound volume. This setting allows you to save power and get the maximum possible running time for your camera’s batteries. Turn the LCD and camera off automatically after a consecutive period of inactivity. Press the left/right button to adjust the volume and Press the button to confirm.
PAGE 66
Language Date & Time Refer to the “Reset your language” section on page 19. Refer to the “Reset Date/Time” section on page 20. World Time LCD Brightness The world time setting is a useful function for your overseas trips. This feature enables you to display the local time on the LCD while you are abroad. Use this setting to adjust the brightness of your LCD. 1. Press the up/down to select the departure place ( ) and destination ( ) fields. 2.
PAGE 67
File Setting Format Mode : 1. Press the button, press the up/down button to select and press the button to enter the menu. 2. Press the up/down button to select and press the button or right button to enter the menu. Please note: formatting enables you to delete all contents in the memory card and built-in memory, including protected photo and movie files. Format Copy to Card File Numbering Reset FW Version <> >> 4.
PAGE 68
Copy to Card File Numbering Use this setting to copy the files stored in the built-in memory to a memory card. After you take a picture or video clip, the camera will save it with a sequential number. You can use this to reset the file numbering to 0001. If there is no card available in the camera, this function will not be displayed.
PAGE 69
Reset FW Version Use this setting to restore the camera to its original default settings. Use this setting to view the current camera firmware version. FW Version Current Ver: X.XX Back When there is a new firmware version in the memory card, select「Yes」to update. FW Version Current Ver: X.XX New Ver: X.
PAGE 70
Connection Settings Connecting to a Computer You can use a Micro USB cable to connect the camera and copy (transmit) photos to a computer, printer or other device. 4. Press the up/down buttons to select「PC」 and press the button to confirm. Setting the USB Mode The camera’s USB port can be set to connect with either a computer or a printer. The following steps will allow you to ensure that the camera is correctly configured to connect with a PC. 1.
PAGE 71
Transferring files to your computer The computer will automatically detect the camera as a removable drive. Double-click the my computer icon on the desktop to locate the removable drive and to copy folders and files in the drive to a directory on your PC as you would copy any typical folder or file. Follow the steps below to connect the camera to a computer. 1. Make sure the computer is turned on. 2. Connect one end of the supplied Micro USB cable to the USB port on your camera. 3.
PAGE 72
Connecting to a PictBridge Compatible Printer PictBridge technology allows printing of the photos saved in the memory card by the printer. 3. Press the up/down button to select「USB」 and press the button or right button to enter the menu. To find out if a printer is PictBridge compatible, simply look for the PictBridge logo on the packaging or check the owner's manual for specifications.
PAGE 73
Connecting to your Printer 1. Make sure the printer is turned on. 2. Connect one end of the supplied Micro USB cable to the USB port on your camera. If the camera is not connected to a PictBridge compatible printer, the following error message will appear on the LCD. 3. Connect the other end of the Micro USB cable to the USB port on the printer.
PAGE 74
Using the PictBridge Menu After setting the USB mode to Printer, the PictBridge menu will appear. Print (with Date) If you have set the date and time on your camera, the date and time will be recorded and saved with each photo you take. 1. In the PictBridge menu, select「Print (with Date)」and the screen as shown below appears. Press the up/down button to select a menu item and press the button or right button to enter the item. Refer to the following sections for more detailed information on each setting.
PAGE 75
Print (without Date) 3. Press the up/down button to select the number of copies for the currently displayed photo. 4. Press the button and the following screen will appear. 5. Select「Yes」and press the button to confirm printing; select「Cancel」and press the button to cancel printing. Use this setting to print the photos without dates on them. 1. In the PictBridge menu, select「Print (without Date)」and the screen as shown below appears. 2. Press the left/right button to select a photo to be printed. 3.
PAGE 76
Print Index You can print all photos in the camera via this function. 1. In the PictBridge menu, select「Print Index」and the screen as shown below appears. 5. Select「Yes」and press the button to confirm printing; select「Cancel」and press the button to cancel printing. 2. Select「Yes」and press the button to confirm printing; select「Cancel」and press the button to cancel printing.
PAGE 77
Print DPOF Images Exit To use DPOF printing, you must select your photos for printing using the DPOF settings beforehand. See “DPOF” section on page 62. Select「Exit」to exit the PictBridge menu. At this time, the message「Remove USB Cable!」 appears on the screen. 1. In the PictBridge menu, select「Print DPOF Images」and the screen as shown below appears. Disconnect the Micro USB cable from the camera and printer. 2.
PAGE 78
Video System You can use the AV cable (which should be purchased separately) to connect the camera and the television for realizing the video output. Connect one end of the AV cable to AV port of the camera, connect the other end to AV-OUT port of the television. Adjust the format of the video output system according to your requirements, and the steps are as follows: 1. Press the button, press the up/down button to select and press the button to enter the menu. 2.
PAGE 79
Set Eye-Fi Card Connection Mode This camera supports wireless connection for Eye-Fi memory cards. Enable the Eye-Fi connection by following the steps below. 1. Press the menu. button, press the up/down button to select 2. Press the up/down button to select menu. and press the and press the button to enter the button or right button to enter the 3. Press the up/down button to select「Eye-Fi」and press the the menu. button or right button to enter 4.
PAGE 80
Appendices Product Specifications Design and specifications are subject to change without notice. Image Sensor Lens Type 1/2.3"CCD Effective Pixels 16.15 Megapixels Total Pixels 16.44 Megapixels Focal Length 4.3mm (Wide) — 64.5mm (Tele) 35mm film equivalent 24mm (Wide) — 360mm (Tele)] F number F3.3 (Wide) — F5.
PAGE 81
Number of Recording Pixels Still Image (4:3) 16MP: 4608×3456 10MP: 3648×2736 5MP: 2592×1944 3MP: 2048×1536 0.3MP: 640×480 Movie 1280×720 (15/30fps), 640×480 (30fps) Image Compression (3:2) 14MP: 4608×3072 (16:9) 12MP: 4608×2592 2MP: 1920×1080 Best, Fine, Normal DCF, DPOF (Ver1.1) Support Yes File Format 80 Still Image Exif 2.3 (JPEG) Movie MOV [Image: Motion JPEG; Audio: G.
PAGE 82
Panorama Up to 180° (Horizontal） LCD Display 3.
PAGE 83
Flash Flash Method Pop-up (Manual) Flash Modes Force Off, Flash Auto, Fill Flash, Slow Sync., Slow Sync. + Red-Eye, Red-Eye Reduction Internal Memory: Approx. 8MB 82 Recording Media SD/SDHC Card (Up to 32GB Support) (MMC Card Not support ) Multi-Language Support 27 Languages Jacks AV-OUT/USB 2.0 (Micro 5 pin USB) Eye-Fi Support Yes Power Rechargeable Li-ion Battery LB-052, 3.7V 880mAh, In-Camera Charging Shooting Capability (Battery Performance) Approx.
PAGE 84
Prompts and Warning Messages Message Description Action Warning! Battery exhausted. The camera battery is used up. It is a warning indicating that the camera is going to shut down. Charge the battery. Lens obstruction, Re-start Camera. The lens is jammed or some foreign object is preventing the lens from functioning properly. Turn off the camera and restart it to reset the lens. Suggest using tripod. The message will appear when shooting in low light/illuminated scenes.
PAGE 85
Message 84 Description Action Improper alignment. Please try again. The offset is too big for panorama shooting. The message will disappear after 2 seconds. Connection Failed! In the case of failing to connect to a PC or a printer. Remove transmission line to stop connection, and the message is removed. Warning! Do not turn off your camera during update! The message appears during the firmware update process. The message disappears after the camera update and restart.
PAGE 86
Message Description Action Memory Full ! Indicates that the internal memory is full. Insert a new memory card or delete unwanted images. Card Error ! The memory card cannot be recognized after being formatted. Insert a new memory card or format the card with this camera. Card is not formatted. The inserted memory card is unformatted or has been formatted on a computer or other device and is not compatible with this camera. Disappear after 2 seconds and enter the formatting process.
PAGE 87
Message 86 Description Action This image cannot be edited. The file format does not support editing or the edited file cannot be edited again. The message will disappear after 2 seconds. Exceeded maximum folder number. Prompt message when the archives or file folders in the memory card have reached the maximum (9999 for archives, 999 for file folder). Copy the images to your PC and format the memory card with this camera. Too many pictures for quick processing.
PAGE 88
Troubleshooting Problem Camera does not turn on Camera turns off suddenly during operation The picture is blurred Images and video files cannot be saved Possible causes The battery has been depleted. The battery is not inserted correctly. The batteries have been depleted. Camera shakes while taking a picture. The memory card is full. The memory card is locked. The camera is not connected to the printer correctly. Images will not print from the connected printer The printer is not PictBridge compatible.
PAGE 89
88 Problem Saving data to memory card is slow Possible Causes Using a memory card below Class 4 may result in slower recording times. Solution Use a memory card with write Class 4 or higher than 4 to improve performance. Cannot write to the memory card The memory card has been locked. Too many movies to process The number of pictures or folders in the memory card exceed the specifications, so the playback of data folder can not be displayed.
PAGE 90
The Kodak trademark and trade dress are used under license from Kodak. © 2015 by JK Imaging Ltd. All Rights Reserved. JK Imaging Ltd., 17239 South Main Street, Gardena, CA 90248, USA JK Imaging Europe, 71 Clarendon road, Watford, WD17 1DS, UK www.kodakpixpro.com Ver.