Document Scanner 5500 and 7500 Installation Questionnaire Instructions A-61074 Part Number 6C3944 Mode Setup Software
Table of contents A-61074 April 1997 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Logon procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the Mode Setup Software . . . . . . . . . . . . . . . . . . . . . .
IA Display format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Adjoining IA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Batching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Length monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . On/off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Minimum length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Maximum length .
1 Introduction The Kodak Digital Science™ Mode Setup Software 5000/7000 has been developed to enable you to customize applications using the Kodak Digital Science Document Scanner 5500 and 7500. The Mode Setup Software offers a user-friendly interface which allows you to perform an initial installation or modification of an existing setup.
Logon procedure After the installation procedure is completed, perform the following steps to logon to the Mode Setup Software: 1. Access DOS. 2. Change the directory to correspond to the directory designated during the installation procedure. 3. Type SETUP and press Enter. The following screen appears: KODAK DIGITAL SCIENCE (tm) Scanner 5000/7000 This software is the property of Eastman Kodak Company. It is not to be sold or leased in any form.
5. Select Continue. 6. Press Enter. The following screen appears: Configuration Items Display Language Measurement System Date Format Time Format Set Time and Date Confirmation Tone Volume Confirmation Tones Fixed Field Delimiter Printer Messages Version Numbers Load scanner from laptop Load laptop from scanner Setting DIGITAL SCIENCE Status READY English Inch 1990/10/10 00:00 Soft Enabled Period (.
To select the Previous Menu option: — Use the arrow keys to position the highlight cursor over the Previous Menu option or press the Pagedown key to automatically position the highlight cursor over the Previous Menu option. — Press Enter. • If a message is received which indicates that an accessory is not installed, press Enter to continue. This message indicates that the option selected requires an accessory which is not physically installed and/or properly defined to the software.
2 Scanner configuration items Accessing the Configuration Items Menu Configuration Items Display Language Measurement System Date Format Time Format Set Time and Date Confirmation Tone Volume Confirmation Tones Fixed Field Delimiter Printer Messages Version Numbers Load scanner from laptop Load laptop from scanner Setting DIGITAL SCIENCE Status READY English Inch 1990/10/10 00:00 Soft Enabled Period (.
Display language Display language defines the primary display language. The default is English. The options are: English or Japanese (displayed in Katakana characters). • Select Display Language from the Configuration Items window. NOTE: Other languages may appear in the Display Language box; however, only English and Japanese are supported.
Measurement system Measurement system defines the primary measurement system. The default is Inch. The options are: — Inch—uses inches as the primary unit of measure. — Milli—uses millimetres as the primary unit of measure. • Select Measurement System from the Configuration Items window.
Date format Date format defines the date display format; both the date format and delimiter. The default format is mmddyy. The default delimiter is a slash (/ ). Refer to Description 1: Date Format Samples for a description of the available options. • Select Date Format from the Configuration Items window.
Time format Time format defines the time display format. The default is 12 hour with AM/PM. Refer to Description 2: Time Format Samples for a description of the available options. • Select Time Format from the Configuration Items window.
Set time and date Set time and date sets the system clock. The default time is 00:00; the default date is 10/10/90. The options are: — to set each individual time and date field separately. — transfer the internal time and date settings of the computer used during configuration to set the system clock. • Select Set Time and Date from the Configuration Items window and press Enter.
To set the internal time and date settings: • Select a single field (month, day, year, hour, or minute) and press Enter. The sample window assumes that the month field was selected. Configuration Items Setting Display Language Measurement System Date Format Time Format Set Time and Date Confirmation Tone Volume Confirmation Tones Fixed Field Delimiter Printer Messages Load scanner from laptop Load laptop from scanner English Inch 1990/10/10 00:00 Soft Enabled Period (.
Repeat this step for each of the time/date fields to be set. NOTE: The time may also be altered using Function Code F21–Set Time; and the date may also be altered using Function Code F22—Set Date. Both the time and the date may be displayed (but not altered) using Function Code F23—View Date and Time. Confirmation tone volume Confirmation tone volume defines the volume of the confirmation tones (for footswitch, patch reader and bar code reader). The default is Soft.
Confirmation tones Confirmation tones enables or disables all confirmation tones (for footswitch, patch reader and bar code reader). The default is Enable. The options are: —Enable—indicates that confirmation tones may be used. —Disable—indicates that confirmation tones may not be used. • Select Confirmation Tones from the Configuration Items window.
Fixed field delimiter Fixed field delimiter defines the fixed field delimiter used in the image address display. The default is Period (.). The options are: — Slash (/) — Dash (–) — Period (.) — Space ( ) Refer to Description 3: Fixed Field Delimiter Samples for a description of the available options. • Select Fixed Field Delimeter from the Configuration Items window.
Printer messages Printer messages define the messages which may be printed by the front document printer and/or rear document printer. The messages defined here may be printed by including the desired message number in the document printer print definitions using Mode Configuration items specified in the Front Document Printer Print Definitions and/or Rear Document Printer Print Definitions sections. The default is blank messages. The message text may have up to 38 characters.
Version numbers Display the curent scanner firmware versions. • Select Version Numbers from the Configuration Items Window. Configuration Items Display Language Measurement System Date Format Time Format Set Time and Date Confirmation Tone Volume Confirmation Tones Fixed Field Delimiter Printer Messages Version Numbers Load scanner from laptop Load laptop from scanner 2-12 Setting DIGITAL SCIENCE Status READY English Inch 1990/10/10 00:00 Soft Enabled Period (.
Load scanner from laptop Used to upload a configuration file from diskette to the Scanner 5500/7500. • Select Load Scanner from Laptop from the Configuration Items window.
Load laptop from scanner Used to download a configuration file from the Scanner 5500/7500 onto diskette. This is useful in creating configuration files which may be transported to other Digital Science Scanners. This is also used to create backup files. This option should be performed any time an installation or setup change is completed. • Select Load Laptop from Scanner from the Configuration Items window.
3 Mode configuration Accessing the Mode Configuration Menu The following section describes how to access the Mode Configuration menu, how to copy mode definitions from one mode to another, how to select a mode for definition, and how to select each item for definition.
Mode-to-mode copying A number of modes might have similar definitions. The mode to mode copy feature allows you to fully define one mode and then copy that mode definition to another mode, saving the time and effort required to fully define each mode.
• Select a mode which contains the definitions you wish to copy to another mode from the Copy From Mode list.
Selecting a mode for configuration Perform the following steps to select a mode for configuration. NOTE: Not all items available for definition need to be defined. If you wish to allow an item to default or have performed a Mode to Mode copy after fully defining the Copy From Mode, there is no need to define each item.
Index format Index format defines the index format used by the application mode selected. Refer to Description 1: Index Formats for a description of the index formats.
Description 1: Index Formats There are five Index Format options available: • Single Level IA 1 (Level 1) IA 2 (Level 1) IA 3 (Level 1) IA 4 (Level 1) Whenever a document is assigned Level 1, the image address field associated with Level 1 (Field A) is incremented. • Two Level IA 1.0 (Level 2) IA 1.1 (Level 1) IA 1.2 (Level 1) IA 2.
Description 1: Index Formats (continued) • Three Level IA 1.0.0 (Level 3) IA 1.1.0 (Level 2) IA 1.1.1 (Level 1) IA 2.0.0 (Level 3) Whenever a document is assigned Level 3, the image address field associated with Level 3 (Field C) is incremented and the fields associated with Level 2 (Field B) and Level 1 (Field A) are set to zero.
IA Field width IA Field width defines the image address (IA) field widths. Refer to Description 2: Image Address Fields for a description of proper field definitions. • Select IA Field Width from the Mode Configuration window. Mode Number: 01 Mode Name: MODE01 Item #: 2.
Field A (Level 1) Field A represents Level 1. Its value is incremented when a small image mark is placed next to a document and/or a document is assigned Level 1. • Select Field A. Refer to Description 3: Image Address Field Width Defaults for a complete listing of the default values for each mode. Mode Number: 01 Mode Name: MODE01 Item #: 2.
Field B (Level 2) Field B represents Level 2. Its value is incremented when a medium image mark is placed next to a document and/or a document is assigned Level 2. • Select Field B. Refer to Description 3: Image Address Field Width Defaults for a complete listing of the default values for each mode. Mode Number: 01 Mode Name: MODE01 Item #: 2.
Field C (Level 3) Field C represents Level 3. Its value is incremented when a large image mark is placed next to a document and/or a document is assigned Level 3. • Select Field C. Refer to Description 3: Image Address Field Width Defaults for a complete listing of the default values for each mode. Mode Number: 01 Mode Name: MODE01 Item #: 2.
Fixed field Fixed field contains fixed information, typically the date. • Select Fixed Field. Refer to Description 3: Image Address Field Width Defaults for a complete listing of the default values for each mode. Mode Number: 01 Mode Name: MODE01 Item #: 2.
Description 2: Image Address Fields An image address is a unique identifier assigned to each individual document by the Scanner 5500 or 7500. An image address may contain up to 15 characters; consisting of a maximum of 12 digits and a maximum of 3 delimiters. Four fields must be defined: • Field A represents Level 1. Its value is incremented when a small image mark is placed next to a document and/or a document is assigned Level 1. • Field B represents Level 2.
Description 3: Image Address Field Width Defaults The default field widths for each mode are provided below: Fixed Field Field C Level 3 Field B Level 2 Field A Level 1 Example Mode 1 6 0 0 6 FFFFFF.AAAAAA Mode 2 6 0 6 0 FFFFFF.BBBBBB Mode 3 6 0 3 3 FFFFFF.BBB.AAA Mode 4 6 3 3 0 FFFFFF.CCC.BBB Mode 5 4 2 3 3 FFFF.CC.BBB.AAA Mode 6 6 0 4 2 FFFFFF.BBBB.AA Mode 7 6 0 6 0 FFFFFF.BBBBBB Mode 8 4 2 3 3 FFFF.CC.BBB.AAA Mode 9 4 2 3 3 FFFF.CC.BBB.
Level rules Level rules define the level of a document based upon the level of the previous document. These definitions are used as defaults when the document level is not determined by another method (i.e., footswitch, level key, etc). • Select Level Rules from the Mode Configuration window. Mode Number: 01 Mode Name: MODE01 Item #: 3.
Level to follow level 0 NOTE: This menu option is a valid selection when using any of the available index formats defined using the Index Format option. • Select Level 0. Refer to Description 4: Level Rule Options and Defaults for a complete listing of the valid selections and default values for each mode. Mode Number: 01 Mode Name: MODE01 Item #: 3.
Level to follow level 1 NOTE: This menu option is a valid selection when using any of the available index formats defined using the Index Format option. • Select Level 1. Refer to Description 4: Level Rule Options and Defaults for a complete listing of the valid selections and default values for each mode. Mode Number: 01 Mode Name: MODE01 Item #: 3.
Level to follow level 2 NOTE: This menu option is a valid selection only when using any of the two-level (two level or two level offset) or three-level (three level or three level offset) index formats defined using the Index Format option. • Select Level 2. Refer to Description 4: Level Rule Options and Defaults for a complete listing of the valid selections and default values for each mode. Mode Number: 01 Mode Name: MODE01 Item #: 3.
Level to follow level 3 NOTE: This menu option is a valid selection only when using any of the three-level (three level or three level offset) index formats defined using the Index Format option. • Select Level 3. Refer to Description 4: Level Rule Options and Defaults for a complete listing of the valid selections and default values for each mode. Mode Number: 01 Mode Name: MODE01 Item #: 3.
Description 4: Level Rule Options and Defaults The default level rules for each mode are provided below: Level 0 is followed by Level 1 is followed by Level 2 is followed by Level 3 is followed by Mode 1 Level 1 Level 1 Level 1 Level 3 Mode 2 Level 2 Level 1 Level 2 Level 3 Mode 3 Level 2 Level 1 Level 2 Level 3 Mode 4 Level 3 Level 1 Level 2 Level 2 Mode 5 Level 2 Level 1 Level 2 Level 2 Mode 6 Level 2 Level 2 Level 2 Level 3 Mode 7 Level 2 Level 2 Level 2 Level 3 M
Description 4: Level Rule Options and Defaults (continued) The valid level rule options for each index format are provided below: Level 0 may be followed by Level 1 may be followed by Level 2 may be followed by Level 3 may be followed by Single Level Level 0 Level 1 Level 0 Level 1 n/a n/a Two Level Level 0 Level 1 Level 2 Level 0 Level 1 Level 2 Level 0 Level 1 Level 2 n/a Two Level Offset Level 0 Level 1 Level 2 Level 0 Level 1 Level 2 Level 0 Level 1 Level 2 n/a Three Level Level 0
IA Display format Defines the format of the image address display which appears on the control panel. The default for all modes is Suppress Leading Zeroes. The options are: — Display Leading Zeroes (i.e., 001.002.003.004) — Suppress Leading Zeroes (i.e., 001. 2. 3. 4) • Select IA Display Format from the Mode Configuration window. Mode Number: 01 Mode Name: MODE01 Item #: 4.
Adjoining IA Defines the image address assigned to the rear side image of a document scanned in duplex mode. The default for all modes is Front then Rear. The options are: — Sequential—indicates that the rear side image of a document scanned in duplex mode will be assigned a unique image address—incremented from the image address assigned to the front side image.
Batching Batching defines the number of documents of a specified level to process prior to performing a predefined action. The batching option is not available. • If you select Batching from the Mode Configuration window, the following message will appear: Selection is not available. • Press Enter to close the message. • Make another selection from the Mode Configuration window.
On/off Enables or disables length monitoring. The default for all modes is Disable. The options are: — Disable—disables all length monitoring. — Enable—enables all length monitoring. NOTE: If Disable is selected, definitions for the remaining document length monitor options will be ignored. • Select On/Off from the Length Monitor menu. Mode Number: 01 Mode Name: MODE01 Item #: 7.
Minimum length Defines the minimum document length accepted. The default for all modes is 2.500 inches / 64 mm. The options are: — Within the range of 2.500 inches / 64 mm minimum to 20.000 inches / 508 mm maximum. • Select Minimum Length from the Length Monitor menu. Mode Number: 01 Mode Name: MODE01 Item #: 7.
Maximum length Defines the maximum document length accepted. The default for all modes is 13.000 inches / 330 mm. The options are: — Within the range of 2.500 inches / 64 mm minimum to 20.000 inches / 508 mm maximum. • Select Maximum Length from the Length Monitor menu. Mode Number: 01 Mode Name: MODE01 Item #: 7.
Error response Error response defines the action taken when a document shorter than the minimum length or longer than the maximum length is fed into the Scanner 5500/7500. The default for all modes is Display and Beep. The options are: — Display Error Message—results in an error message appearing on the Operator Control Panel (E106–Doc Length Monitor Warning).
Skew monitor Skew monitor defines the options required to enable/disable the document skew monitor, set the amount of acceptable document skew, and what action is to be taken when document skew is detected. NOTE: In order for the skew monitor to operate correctly, the following conditions must be true: — The amount of skew must be less than 30 degrees. — The document(s) must be center-fed. — The document(s) fed must be at least 3 inches / 75 mm wide.
On/off The on/off enables or disables skew monitoring. The default for all modes is Disable. The options are: — Disable—disables all skew monitoring. — Enable—enables all skew monitoring. NOTE: If Disable is selected, definitions for the remaining document skew monitor options will be ignored. • Select On/Off from the Skew Monitor menu. Mode Number: 01 Mode Name: MODE01 Item #: 8.
Detection range Detection range defines the amount of tolerable skew. The default for all modes is 10–30 degrees. The options are: — 5–30 degrees—results in an error being reported if the amount of document skew is between 5 and 30 degrees. — 10–30 degrees—results in an error being reported if the amount of document skew is between 10 and 30 degrees. • Select Detection Range from the Skew Monitor menu. Mode Number: 01 Mode Name: MODE01 Item #: 8.
Error response Error response defines the action taken when a document skew is detected. The default for all modes is Display and Beep. The options are: — Display Error Message—results in an error message appearing on the Operator Control Panel (E107–Doc Skew Monitor Warning). — Display and Beep—results in an error message appearing on the Operator Control Panel (E107–Doc Skew Monitor Warning), accompanied by an error tone.
Footswitch Footswitch defines the options required when using the footswitch accessory. • Select Footswitch from the Mode Configuration window. Mode Number: 01 Mode Name: MODE01 Item #: 9.
Press definition Press definition defines the action which is taken when the footswitch is pressed. The default for all modes is No Action. The options are: — Level 0—document Level 0 will be assigned to the next document. — Level 1—document Level 1 will be assigned to the next document. — Level 2—document Level 2 will be assigned to the next document. — Level 3—document Level 3 will be assigned to the next document.
Confirmation tone Confirmation tone enables or disables the Confirmation Tone which sounds when the Footswitch is pressed or released. The default for all modes is Disable. The options are: — Disable—results in no tone sounding when the footswitch is pressed or released. — Enable—results in a tone sounding when the footswitch is pressed and released. • Select Confirmation Tone from the Footswitch menu. Mode Number: 01 Mode Name: MODE01 Item #: 9.
Release definition Release definition defines the action which is taken when the footswitch is released. The default for all modes is No Action. The options are: — Level 0—document Level 0 will be assigned to the next document. — Level 1—document Level 1 will be assigned to the next document. — Level 2—document Level 2 will be assigned to the next document. — Level 3—document Level 3 will be assigned to the next document. — No Action—results in no action taking place when the footswitch is pressed.
Patch reader NOTE: The patch reader is an accessory which must be installed and enabled by your Field Engineer. Patch reader defines the options required when using the patch reader accessory. • Select Patch Reader from the Mode Configuration window. Mode Number: 01 Mode Name: MODE01 Item #: 10.
On/off On/off enables or disables patch reading. The default for all modes is Disable. The options are: — Disable—disables all patch reading. — Enable—enables all patch reading. NOTE: If Disable is selected, definitions for the remaining patch reader options will be ignored. • Select On/Off from the Patch Reader menu. Mode Number: 01 Mode Name: MODE01 Item #: 10.
Transfer patch definition Transfer patch definition defines the document level assigned to the next document when a transfer patch is used. The default for all modes is Not Used. The options are: — Level 1—document Level 1 will be assigned to the next document. — Level 2—document Level 2 will be assigned to the next document. — Level 3—document Level 3 will be assigned to the next document. — Not Used—indicates that transfer patches are not used.
Confirmation tone Confirmation tone enables or disables the Confirmation Tone which sounds when a patch document is detected. The default for all modes is Disable. The options are: — Disable—results in no tone sounding when a patch document is detected. — Enable—results in a tone sounding when a patch document is detected. • Select Confirmation Tone from the Patch Reader menu. Mode Number: 01 Mode Name: MODE01 Item #: 10.
Level transfer on T-Patch Level transfer on T-Patch defines whether the transfer patch definition is applied to the document containing the transfer patch or the next document fed into the Scanner 5500/7500. The default for all modes is Disabled. The options are: — Disabled—indicates that the next document fed into the Scanner 5500/7500 will be assigned the document level defined by the Transfer Patch Definition option.
COIN2 Port Select The COIN2 Port Select option is not available. • If you select COIN2 Port Select from the Mode Configuration window, the following message will appear: Selection is not available. • Press Enter to clear the message and make another selection from the Mode Configuration window. OCR The OCR option is not available. • If you select OCR from the Mode Configuration window, the following message will appear: Selection is not available.
Bar code reader NOTE: The bar code reader is an accessory which must be installed and enabled by your Field Engineer. Bar code reader defines the options required when using the bar code reader accessory. • Select Bar Code Reader from the Mode Configuration window. Mode Number: 01 Mode Name: MODE01 Item #: 13.
On/off On/off enables or disables bar code reading. The default for all modes is Disable. The options are: — Disable—disables all bar code reading. — Enable—enables all bar code reading. NOTE: If Disable is selected, definitions for the remaining bar code reader options will be ignored. • Select On/Off from the Bar Code Reader menu. Mode Number: 01 Mode Name: MODE01 Item #: 13.
Bar code type Bar code type defines the type of bar code which will be used. The default for all modes is Codabar (NW-7). The options are: — 3 of 9 — Interleaved 2 of 5 — Codabar (NW-7). NOTE: For additional information regarding these bar code types and their characteristics, refer to Bar Code Made Easy (A-61099). • Select Bar Code Type from the Bar Code Reader menu. Mode Number: 01 Mode Name: MODE01 Item #: 13.
Codes per document Codes per document defines the number of codes per document to be read/decoded. The default for all modes is One Code Decoded. The options are: — One Code Decoded—results in only the first bar code encountered on a document being read/decoded. — All Codes Decoded—results in all bar codes encountered on a document being read/decoded. • Select Codes Per Document from the Bar Code Reader menu. Mode Number: 01 Mode Name: MODE01 Item #: 13.
Minimum code length Minimum code length defines the minimum bar code length allowed, in terms of the number of characters encoded. The default for all modes is 3. The options are: — Within the range of 3 to 40 characters. • Select Minimum Code Length from the Bar Code Reader menu. Mode Number: 01 Mode Name: MODE01 Item #: 13.
Maximum code height Maximum code height defines the maximum bar code height allowed. This definition is required only when the Codes Per Document option is defined as All Codes Decoded. The default for all modes is 1 inch / 25.400 mm. The options are: — Within the range of 0.375 inches / 9.525 mm to 3.000 inches / 76.200 mm. • Select Maximum Code Height from the Bar Code Reader menu. Mode Number: 01 Mode Name: MODE01 Item #: 13.
Scan direction Scan direction defines whether the bar code is read in one direction; from left to right, or in two directions; from left to right or right to left. NOTE: When bar codes are read in two directions (bidirectional), the time required to read/decode bar codes is extended. The default for all modes is Unidirectional. The options are: — Unidirectional—results in bar codes being read in only one direction (left to right), requiring that the start character be to the left.
Code quality Code quality defines whether image processing is required to enhance the overall quality of the bar codes to ensure the highest possible read rates. Typically, image processing is required only when dot matrix printers are used to generate the bar codes being read/decoded. The default for all modes is Normal Quality. The options are: — Low Quality—results in image processing is performed to enhance bar code readability.
Confirmation tone Confirmation tone enables or disables the confirmation tone which sounds when the bar code reader detects a bar code document. The default for all modes is Disable. The options are: — Disable—no tone will sound when a bar code document is detected. — Enable—a tone will sound when a bar code document is detected. • Select Confirmation Tone from the Bar Code Reader menu. Mode Number: 01 Mode Name: MODE01 Item #: 13.
Bar code location Bar code location defines whether the bar codes are to be located on the front or rear of the document(s). The default for all modes is Front. The options are: — Front—the bar code reader attempts to detect bar codes on the front side of each document. — Rear—the bar code reader attempts to detect bar codes on the rear side of each document. NOTE: This option is only valid when using a duplex Scanner 5500/ 7500.
Printer controller NOTE: The printer controller is an accessory which must be installed and enabled by your Field Engineer. Printer controller defines the options required when using the printer controller accessory with a Front Printer and/or a Rear Printer. • Select Printer Controller from the Mode Configuration window. Mode Number: 01 Mode Name: MODE01 Item #: 14.
IA Print format IA Print format defines the format of the image address printed by the front printer and/or the rear printer. The default for all modes is Suppress Leading Zeroes. The options are: — Display Leading Zeroes (i.e., 001.002.003.004) — Suppress Leading Zeroes (i.e., 001. 2. 3. 4) — Compress Leading Zeroes (i.e., 001.2.3.4). • Select IA Print Format from the Printer Controller menu. Mode Number: 01 Mode Name: MODE01 Item #: 14.
Font size Font size defines the size of the characters printed by the front printer and/or the rear printer. The default for all modes is Small (8x9). The options are: — Small (8x9)—results in characters printed using an 8x9 matrix. — Large (12x9)—results in characters printed using a 12x9 matrix. • Select Font Size from the Printer Controller menu. Mode Number: 01 Mode Name: MODE01 Item #: 14.
Character orientation Defines the orientation of the characters printed by the front printer and/or the rear printer. The default for all modes is Cine. The options are: • Comic • Comic 180 • Cine • Cine 180 The following illustrate the appearance of each orientation: COMIC180 C I N E 1 8 0 COMIC C I N E • Select Character Orientation from the Printer Controller menu. Mode Number: 01 Mode Name: MODE01 Item #: 14.
Front printer NOTE: The front printer is an accessory which must be installed and enabled by your Field Engineer. Front printer defines the options required when using the front printer accessory. • Select Front Printer from the Mode Configuration window. Mode Number: 01 Mode Name: MODE01 Item #: 15.
On/off On/off enables or disables printing by the front printer. The default for all modes is Disable. The options are: — Disable—disables printing by the front printer. — Enable—enables printing by the front printer. NOTE: If Disable is selected, definitions for the remaining front printer options will be ignored. • Select On/Off from the Front Printer menu. Mode Number: 01 Mode Name: MODE01 Item #: 15.
Print definition Print definition defines what information is printed by the front printer. This is dependent upon the document level assigned to the document being printed upon. You may choose one of five options. These options are described below. The procedure for choosing these options is further described on the following pages. • Same Format Per Level—Defines what information is printed by the front printer on all documents, regardless of the document level assigned to the document.
The procedure for defining the previously mentioned options is described below. Defining Level 1 is used as an example. • Select Print Definition from the Front Printer menu. The print definition options are displayed: Mode Number: 01 Mode Name: MODE01 Item #: 15.
• Select an item from the list of print definition options. • Press Enter. The item selected should appear in the New Print Sequence Display Items box. Repeat this step for each item you wish to include in the print definition for Level 1 document. NOTE: The front printer will print a maximum of 38 characters-perdocument. If the print definition exceeds 38 characters, only the first 38 characters will be printed.
• Use the arrow keys to increase or decrease the current distance: — The left arrow key will decrease the value in 0.125 inch or 1 mm increments. — The right arrow key will increase the value in 0.125 inch or 1 mm increments. — The down arrow key will decrease the value in 1.250 inch or 20 mm increments. — The up arrow key will increase the value in 1.250 inch or 20 mm increments. • Press Enter. Rear printer NOTE: The rear printer is an accessory which must be installed and enabled by your Field Engineer.
On/off On/off enables or disables printing by the rear printer. The default for all modes is Disable. The options are: — Disable—disables printing by the rear printer. — Enable—enables printing by the rear printer. NOTE: If Disable is selected, definitions for the remaining rear printer options will be ignored. • Select On/Off from the Rear Printer menu. Mode Number: 01 Mode Name: MODE01 Item #: 16.
Print definition Print definition defines what information is printed by the rear printer on all documents, regardless of the document level assigned to the document. You may choose one of five options. These options are described below. The procedure for choosing these options is further described on the following pages. • Same Format Per Level—Defines what information is printed by the rear printer on all documents, regardless of the document level assigned to the document.
The procedure for defining the previously mentioned options is described below. Defining Level 1 is used as an example. • Select Print Definition from the Rear Printer menu. The print definition options are displayed: Mode Number: 01 Mode Name: MODE01 Item #: 15.
The box entitled Current Print Sequence Display Items contains the current print definition for Level 1 documents. The box entitled New Print Sequence Display Items should be blank. • Select an item from the list of print definition options. The item selected should appear in the New Print Sequence Display Items box. Repeat this step for each item you wish to include in the print definition for Level 1 documents. NOTE: The rear printer will print a maximum of 38 characters-perdocument.
• Use the arrow keys to increase or decrease the current distance: — The left arrow key will decrease the value in 0.125 inch or 1 mm increments. — The right arrow key will increase the value in 0.125 inch or 1 mm increments. — The down arrow key will decrease the value in 1.250 inch or 20 mm increments. — The up arrow key will increase the value in 1.250 inch or 20 mm increments. • Press Enter. Mode name Mode name defines a name for the mode.
Overrides Overrides enable or disable mode overrides. The default for all modes is Discard Overrides. The options are: — Discard Overrides—results in the use of function codes to change programming options being temporary—not overriding the definitions made here. — Save Overrides—results in the use of function codes to change programming options being saved—overriding the definitions made here. • Select Overrides from the Mode Configuration window. Mode Number: 01 Mode Name: MODE01 Item #: 18.
Exiting the mode configuration menu When all of the mode configuration options have been defined for current mode, you will exit the Mode Configuration window. • Select one of the options listed below from the Mode Configuration window: Mode Number: 01 Mode Name: MODE01 Item #: 0.
Appendix A Default summaries Machine Configuration Defaults—All Modes Accessory Configuration Defaults—All Modes Description Default Value Description Default Value Display Language English Printer Controller Not Present Measurement System Inch Front Printer Not Present Date Format Date Delimiter mmddyy slash (/) Rear Printer Not Present Bar Code Reader Not Present Time Format 12 hour with AM/PM Patch Reader Not Present Set Time and Date n/a OCR Subsystem n/a Confirmation Tone
Mode configuration defaults Default Values Description Mode 1 Mode 2 Mode 3 Mode 4 Mode 5 Mode 6 Mode 7 Mode 8 Index Format 1 2Off 2 3Off 3 2 2Off 3 IA Field Widths Fixed Level 3 (C) Level 2 (B) Level 1 (A) 6 0 0 6 6 0 6 0 6 0 3 3 6 3 3 0 4 2 3 3 6 0 4 2 6 0 6 0 4 2 3 3 Level Rules Level 0 followed by Level 1 followed by Level 2 followed by Level 3 followed by Level 1 Level 1 Level 1 Level 3 Level 2 Level 1 Level 2 Level 3 Level 2 Level 1 Level 2 Level 3 Level 3 Level 1 Level
Mode configuration defaults Default Values Mode 9 Mode 10 Mode 11 Mode 12 Mode 13 Mode 14 Mode 15 Mode 16 Mode 17 Mode 18 3 3 3 3 3 3 3 3 3 3 4 2 3 3 4 2 3 3 4 2 3 3 4 2 3 3 4 2 3 3 4 2 3 3 4 2 3 3 4 2 3 3 4 2 3 3 4 2 3 3 Level 2 Level 1 Level 1 Level 2 Level 2 Level 1 Level 1 Level 2 Level 2 Level 1 Level 1 Level 2 Level 2 Level 1 Level 1 Level 2 Level 2 Level 1 Level 1 Level 2 Level 2 Level 1 Level 1 Level 2 Level 2 Level 1 Level 1 Level 2 Level 2 Level 1 Level 1 Level
Mode configuration defaults Default Values Description Mode 1 Mode 2 Mode 3 Mode 4 Mode 5 Mode 6 Mode 7 Mode 8 Patch Reader On/Off Transfer Patch Def.
Mode configuration defaults Default Values Mode 9 Mode 10 Mode 11 Mode 12 Mode 13 Mode 14 Mode 15 Mode 16 Mode 17 Mode 18 Disable None Disable Disable Disable None Disable Disable Disable None Disable Disable Disable None Disable Disable Disable None Disable Disable Disable None Disable Disable Disable None Disable Disable Disable None Disable Disable Disable None Disable Disable Disable None Disable Disable n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a
Appendix B Language support When inputting messages which contain non-ASCII standard characters, refer to the following tables to determine the code assigned to the desired character to be input and then follow the procedure outlined below: NOTE: The message input may have up to 38 characters. • Enter any standard ASCII text using the keyboard, if desired. • To enter non-ASCII standard text: — Press the ALT key to display the Code input box: Definition Printer Messages Msg. No.
Definition Printer Messages Msg. No. 1 2 3 CODE 4 191 5 6 7 8 9 5 ABC NOTE: In this example, it has been determined that the desired character is a Æ, and the code which corresponds to this character is 191. • Press Enter to input the code and close the Code box. The character will be input to the message. Definition Printer Messages Msg. No.
• Press Enter to place the message in the message table when all desired message information has been inputted. You will be asked to confirm the replacement of the current contents of the message with the new message input. When the message, Replace Msg? appears: • Select Yes to confirm that the new message input should replace the old message in the Print Message Definition area; or Select No to cancel the replacement of the old message with the new message input. Definition Printer Messages Msg. No.
Code Number 32 B-4 European Katakana Character Character blank blank Code Number European Katakana Character Character Code Number 50 68 33 51 69 34 52 70 35 53 71 36 54 72 37 55 73 38 56 74 39 57 75 40 58 76 41 59 77 42 60 78 43 61 79 44 62 80 45 63 81 46 64 82 47 65 83 48 66 84 49 67 85 European Katakana Character Character A-61074 April 1997
EASTMAN KODAK COMPANY Business Imaging Systems Rochester, New York 14650 Kodak, Digital Science and the Digital Science monogram are trademarks of Eastman Kodak Company. Printed on recycled paper. A-61074 4/97 © Eastman Kodak Company, 1997 Printed in U.S.A.
