KOBE Range Hoods Brillia Series RAX21 SQB-X Series Under Cabinet Model: RAX2130SQB-1 (30”) / RAX2130SQB-2 (30”) RAX2136SQB-1 (30”) / RAX2136SQB-2 (36”) RAX2142SQB-1 (42”) / RAX2142SQB-2 (42”) Wall Mount Model: RAX2130SQB-WM-1 (30”) / RAX2130SQB-WM-2 (30”) RAX2136SQB-WM-1 (36”) / RAX2136SQB-WM-2 (36”) RAX2142SQB-WM-1 (42”) / RAX2142SQB-WM-2 (42”) INSTALLATION INSTRUCTIONS AND OPERATION MANUAL
IMPORTANT READ THIS FIRST READ BEFORE INSTALLATION 1. Carefully check all contents of package(s). 2. Thoroughly inspect the unit for any shipping damages, cosmetic damages or defects. 3. Have a certified contractor/electrician test the unit before installation. IF THERE IS ANY PROBLEMS: 1. DO NOT INSTALL THE UNIT AND KEEP ALL ORIGINAL PACKAGING MATERIALS. 2. Have your invoice as proof of purchase and product serial number ready. 3.
[ENGLISH] - READ AND SAVE THESE INSTRUCTIONS - CONTENTS IMPORTANT SAFETY INSTRUCTIONS ........................................................................ 1 COMPONENTS OF PACKAGE ...................................................................................... 3 INSTALLATION ............................................................................................................... 5 OPERATING INSTRUCTIONS .....................................................................................
IMPORTANT SAFETY INSTRUCTIONS - PLEASE READ THIS SECTION CAREFULLY BEFORE INSTALLATION - WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY, OBSERVE THE FOLLOWING: 1. Installation and electrical wiring must be done by qualified professionals and in accordance with all applicable codes and standards, including fire-rated construction. 2. When cutting or drilling into wall or ceiling, be careful not to damage electrical wiring or other hidden utilities. 3.
What to Do in the Event of a Range Top Grease Fire 1. SMOTHER FLAMES with a tight fitting lid, cookie sheet, or metal tray, and then turn off the burner. KEEP FLAMMABLE OR COMBUSTIBLE MATERIAL AWAY FROM FLAMES. If the flames do not go out immediately, EVACUATE THE AREA AND CALL THE FIRE DEPARTMENT or 911. 2. NEVER PICK UP A BURNING PAN – You May Get Burned. 3. DO NOT USE WATER, including wet dishcloths or towels – a steam blast will result. 4. Use an extinguisher ONLY if: a.
COMPONENTS OF PACKAGE (Must keep all materials for returns or refunds) For Under Cabinet Application Model No.
(Must keep all materials for returns or refunds) For Wall Mount Application Model No.
INSTALLATION PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING Calculation before Installation To calculate installation, please refer to TABLE 1 and TABLE 2. (All calculations in inches).
UNDER CABINET INSTALLATION Before Installation 1. Read any provided document(s). 2. Test the range hood by temporarily connecting it to an outlet and turning ON the fan and lights. 3. If you run into any problems, contact KOBE Range Hoods. Venting Requirements 4. The range hood has top 6” round exhaust (default). 5. Decided the location of the venting pipe from the hood to the outside. A straight, short vent run will allow the hood to perform more efficiently.
Electrical Wire 17. Connected the range hood to an outlet. 18. If hardware is desired, cut off the plug and connect three wires (black, white, and green) to the outlet wires and cap with wire connectors. Connect the wires according to color (ex. black to black). Finish 19. Remove any protective film from the hood, if any. 20. Before using, make sure that any accessories such as baffle filters are properly installed where applicable. 21. Test the range hood to see if it is working properly.
WALL MOUNT INSTALLATION Before Installation 1. Read any provided document(s). 2. Test the range hood by temporarily connecting it to an outlet and turning ON the fan and lights. 3. If you run into any problems, contact KOBE Range Hoods. Venting Requirements 4. The range hood has top 6” round exhaust (default). 5. Decided the location of the venting pipe from the hood to the outside. A straight, short vent run will allow the hood to perform more efficiently.
Duct Cover Installation 16. Use reference E from TABLE 2 and measurements on page XX to mark the position of the duct cover-mounting bracket. 17. Secure the duct cover-mounting bracket to the wall with two 4*35 screws. Make sure all screws are tightened. Refer to Figure 3. NOTE: Inner duct cover will cover the duct cover-mounting bracket. 18. Put the entire duct cover onto the hood and slide the inner duct cover until it reaches to the duct cover-mounting bracket. 19.
OPERATING INSTRUCTIONS 3-Speed Mechanical Push Button NOTE: For best results, turn fan on prior to any preparation or cooking and keep fans running while cooking. Adjust speed as needed.
MAINTENANCE For optimal performance, clean the range hood surface and filters regularly. To Clean Hood Surface CAUTION: NEVER USE ABRASIVE CLEANERS, PADS, OR CLOTHS. ***Regular care will help preserve its fine appearance. 1. Use only mild soap or detergent solutions. Dry surfaces using soft cloth. 2. If hood looks smudged (stainless steel hood), use a stainless steel cleaner to clean the surface of the hood. Avoid getting cleaning solution onto or into the control panel.
SPECIFICATIONS MODEL / SIZE Under Cabinet Model No. RAX2130SQB-1 (30”) RAX2136SQB-1 (36”) RAX2142SQB-1 (42”) Wall Mount Model No. RAX2130SQB-WM-1 (30”) RAX2136SQB-WM-1 (36”) RAX2142SQB-WM-1 (42”) RAX2130SQB-2 (30”) RAX2136SQB-2 (36”) RAX2142SQB-2 (42”) COLOR Commercial Grade Stainless Steel CONSUMPTION / AMPERE 126W / 1.
MEASUREMENTS & DIAGRAMS ***All inch measurements are converted from millimeters. Inch measurements are estimated. ***All measurements in ( ) are millimeters. - FOR UNDER THE CABINET MODEL NO.: RAX2130SQB-2 (30”) / RAX2136SQB-2 (36”) / RAX2142SQB-2 (42”) MODEL NO.
PARTS LIST MODEL NO.: RAX2130SQB-2 (30”) RAX2136SQB-2 (36”) RAX2142SQB-2 (42”) No. 01 02 03 04 05 06 07 08 Description 6” Round Exhaust Adapter Hood-Mounting Bracket Capacitor LED Light Control Switch Blower System Baffle Filter LED Light Driver Model No. 14 Part No.
MODEL NO.: RAX2130SQB-WM-2 (30”) RAX2136SQB-WM-2 (36”) RAX2142SQB-WM-2 (42”) No. 01 02 03 04 05 06 07 08 09 10 Description Duct Cover-Mounting Bracket Duct Cover 6” Round Exhaust Adapter Hood-Mounting Bracket Capacitor LED Light Control Switch Blower System Baffle Filter LED Light Driver Model No. 15 Part No.
CIRCUIT DIAGRAM MODEL NO.
TROUBLE SHOOTING Issue After installation, both motors and lights are not working. Lights are working, but motor(s) is not. The range hood is vibrating. The motor is working, but the lights are not working. The range hood is not venting out correctly. Cold air is coming into the home. Possible Cause The power is not on. The wire connection is not secure. The control panel is defective. The motor(s) is defective. The capacitor(s) is defective. The control panel is defective.
WARRANTY WARRANTY CERTIFICATE In order to obtain warranty service, you must provide proof of original purchase from a KOBE authorized dealer. Please keep a copy of your original invoice as proof of purchase. ONE-YEAR LIMITED LABOR WARRANTY ON KOBE BRILLIA SERIES: For one year from the date of your original invoice from KOBE authorized dealer, we will repair any parts or components free of charge that failed due to manufacturing defects.
THIS WARRANTY WILL BE VOIDED BY: 1. Improper installation and failure to follow installation instructions. 2. Any repairs, alternation, modification not authorized by KOBE. 3. Duct alternation, modification, and connection. 4. Incorrect electric current, voltage, or wiring. 5. Improper usage of the product such as commercial, outdoor, or other usage other than residential indoor usage. 6. Purchasing this product from an unauthorized KOBE dealer. 7.
WARRANTY INFORMATION FORM Fills in the blanks and keep this paper with the original invoice in a safe place for future service purpose. 1. Date of purchase : _______________________________ 2. Model No. :_______________________________ 3. Serial No. :_______________________________ For warranty service or spare parts purchase in US, contact: KOBE Service Center Email (best): customer.service@koberangehoods.
KOBE Range Hoods 11775 Clark Street Arcadia, CA 91006 USA www.koberangehoods.com This KOBE hood is made for use in the USA and CANADA only. We do not recommend using this hood overseas as the power supply may not be compatible and may violate the electrical code of that country. Using a KOBE hood overseas is at your own risk and will void your warranty. Cette hotte KOBE est fabriquée pour usage aux États-Unis et au Canada seulement.
