Installation Guide

ManualsBrandsKobalt ManualsTool ChestsTRXK412C

F1318A6

Please indicate the following information from the service part drawing provided.

Model Number: ____________________________

Model Description: _________________________

*Product you purchased may vary from picture shown.

Caution: Read and follow all Safety Rules and Operating Instructions before first

use of this product. Retain this document for future reference.

Chests and Cabinets with Ball Bearing Slides

Owner’s Manual

SAFETY

SAFETY WARNINGS AND CAUTIONS:

C DO NOT stand on this product. You may fall which may cause personal injury.

C WEAR SAFETY GLASSES when removing or repositioning the slides. The tool

could slip which may cause personal injury.

C When moving this product, do not pull it. Push the product to prevent personal injury.

C Handle and swivel casters must be attached on the same side of the product.

C USE THE BRAKES when not moving this product. This will prevent the product from

rolling, which may cause personal injury or product damage.

C BE CAREFUL when opening more than one drawer. The product may become

unstable and tip, which may cause personal injury or product damage.

C DO NOT mount this product on a truck bed or any other moving object. This may

cause personal injury or product damage.

C DO NOT step in the drawers. You may fall which may cause personal injury.

C Appropriately secure this product before moving it with a forklift.

C DO NOT tow with power equipment. The product could tip, which may cause

personal injury or product damage.

C DO NOT alter this product in any manner. For example, do not weld external

lockbars or attach electrical equipment. This may cause product damage or personal

injury.

C Keep the product on level surfaces. The product may become unstable and tip if

stored or moved on an un-level surface, which may cause personal injury or product

damage.

C Close the cover and lock the drawers and doors before moving this product. The

drawers or doors could come open and make the product unstable and tip, which

may cause personal injury or product damage.

C When the cover is opened, be sure the cover stop is in the locked position. This will

prevent accidental closure and personal injury.

C BE CAREFUL when closing the cover. Remove hands before the cover closes

completely to prevent personal injury.

C The maximum weight for each drawer should be no more than 50 pounds.

C The maximum product weight, including contents, should be no more than 800

pounds for roller cabinets.

C Remove the work surface, if provided, from the roller cabinet before mounting the

chest. Failure to do so may cause the chest to slide off, which may cause personal

injury or product damage.

• Stacked products should be bolted together. (May need to drill mounting holes.) The

products could become unstable and tip, which may cause personal injury or product

damage.

C When locking a chest, close the drawers before closing the cover for lock bars to

work properly.

C Spread the weight out evenly in the tote trays. If the weight is not spread evenly, the

contents could shift and fall out, which may cause personal injury, and damage to the

contents or tote tray.

In the United States Call 1-888-3KOBALT for Service Parts.

8AM - 8PM Mon - Fri EST.

Outside the United States call your local distributor.

Summary of content (6 pages)

PAGE 1
SAFETY SAFETY WARNINGS AND CAUTIONS: Chests and Cabinets with Ball Bearing Slides Owner’s Manual Please indicate the following information from the service part drawing provided. Model Number: ____________________________ C DO NOT stand on this product. You may fall which may cause personal injury. C WEAR SAFETY GLASSES when removing or repositioning the slides. The tool could slip which may cause personal injury. C When moving this product, do not pull it. Push the product to prevent personal injury.
PAGE 2
HARDWARE INCLUDED Lever Style - Lift or lower (depending on the slide) the release lever on both sides, (this allows the slides to ride over the stops.) Pull out to remove. 14-10 X 3/4 Phillips screw (4) 10-16 X 1 Phillips screw (4) 1/4-20 Hex Nut (16) Some instructions may not apply to your specific unit. CASTER INSTALLATION: Note: Use adequate personnel for this operation. C Note: Mount both swivel casters on the same side of the unit as the handle.
PAGE 3
SEGURIDAD ADVERTENCIAS Y PRECAUCIONES DE SEGURIDAD: Baúles y Gabinetes con Correderas de Rodamientos Esféricos Manual del propietario Sírvase indicar la siguiente información que encontrará en el dibujo suministrado de la pieza de servicio. • NO se ponga de pie sobre la unidad. Podría caerse y lesionarse. • USE GAFAS DE SEGURIDAD al quitar o volver a poner las correderas. Se podría resbalar la herramienta y causar lesiones personales. • Cuando mueva la unidad, no la hale.
PAGE 4
FERRETERÍA INCLUIDA Estilo palanca – Levante o baje (dependiendo de la corredera) la palanca de liberación en ambos lados (esto permite que las correderas pasen sobre los topes.) Hale hacia afuera para retirar. Tornillo Phillips de 14-10 X 3/4 (4) Tornillo Phillips de 10-16 X 1 (4) Tuerca Hexagonal de 1/4-20 (16) NOTA: Algunas instrucciones pueden no aplican a sus unidades específicas. INSTALACION DEL TIRADOR: NOTA: Utilice personal adecuado para esta operación.
PAGE 5
SÉCURITÉ CONSEILS DE SÉCURITÉ ET PRÉCAUTIONS: Coffres et Armoires avec Glissières à Roulements à Billes Manuel de l'utilisateur Fournir les informations demandées cidessous et conserver ce manuel à titre de référence. • NE vous tenez PAS debout sur ce produit. Vous risqueriez de tomber et de vous blesser. • PORTER DES LUNETTES DE PROTECTION lorsqu'on retire ou que l'on repositionne les glissières. L'outil risque de glisser et de causer des blessures.
PAGE 6
MATÉRIEL COMPRIS Selon le levier - Soulevez ou abaissez (selon la glissière) le levier de dégagement sur chaque côté (ce qui permet aux glissières de passer par-dessus les arrêts.) Tirez pour l'enlever. Vis Phillips 14-10 X 3/4 (4) Vis Phillips 10-16 X 1 (4) Ecrou hexagonal de 1/4-20 (16) Certaines instructions peuvent ne pas s’appliquer à votre unité spécifique. INSTALLATION DES ROULETTES: ASSEMBLAGE REMARQUE: Utiliser la main-d'oeuvre nécessaire pour cette operation.