Installation Guide

J-BOLT (NO DRILLING METHOD)
5/16 FLAT
WASHER
“J” BOLT
5/16 NUT
BED LIP
VINYL TAPE
(IF NECESSARY)
TRUCK BOX
3
HIGH SIDE BOX
WWW.KOBALTTOOLS.COM
ASSEMBLY INSTRUCTIONS
3. ATTACH BOX TO TRUCK BED
BED RAIL ATTACHMENT:
Place truck box back in original position. If using the Kobalt
®
Mounting Kit, insert J-bolts up from bottom through the
drilled holes inside truck box and around the bed lip as
shown in gure. If your truck bed is constructed of aluminum,
place the vinyl tape strip between the end of the J-bolt and
the bed rail.
2. MARK AND DRILL
MOUNTING HOLES.
BED RAIL: Mark two small lines
on the underside of the truck box
where the box sits on the bed rail,
one toward the front of the truck and
one toward the rear approximately
3 in. from each end of the truck box.
They will serve as guides to drill
holes to mount the truck box to the bed rail.
If using the Kobalt
®
Mounting Kit (Item #691045, sold
separately), drill 3/16 in. pilot holes and then 3/8 in. holes in
the truck box at each location to the inside of the line (not
through the truck bed rail).
If not using the Kobalt
®
Mounting Kit, drill 3/16 in. pilot holes
and 3/8 in. holes at each location to the outside of the line,
through the truck box AND through the bed rail. If your truck
bed is constructed of aluminum, coat the holes drilled in the
bed with zinc primer.
1. LOCATE IN TRUCK BED.
With the truck on a level surface,
place truck box into position on top
of bed rail, with the front side (doors)
ush with the side of the truck and
support box with blocking. Square
box to the bed and level the box so
the top is horizontal when viewed
from the rear.
1
2
If not using the Kobalt
®
Mounting Kit, use 5/16 in. nuts, bolts,
lock and at washers (not provided) to secure the truck box
to the truck bed rail through the drilled holes.
LEG BRACKET ATTACHMENT: Place leg brackets into
position and install bolts, nuts and washers. If your truck
bed is constructed of aluminum, use nylon washers between
leg bracket feet and truck bed on the top side and between
the at washer and bed on the underside. Tighten all bolts
securely with wrench.
KOBALT® is a registered
trademark of LF, LLC.
All rights Reserved.
Printed in the U.S.A.
WWW.KOBALTTOOLS.COM
ARTICLE #0691040
MODÈLE #101301-9-01
BOÎTE À PAROIS
HAUTES UNIVERSELLE
Kobalt
®
est une marque de commerce
déposée de LF, LLC. Tous droits réservés.
JOIGNEZ VOTRE REÇU ICI
Numéro de série
Date d’achat
Des questions?
CONTENU DE L’EMBALLAGE
QUINCAILLERIE INCLUSE
Boîte de camion
Clés
Communiquez avec notre service à la clientèle au
1-888-3KOBALT (888-356-2258), entre 8 h et 20 h
(HNE), du lundi au vendredi.
HIGH SIDE BOX
ITEM DESCRIPTION ILLUSTRATION
1 LEG HIGH SIDE 246
2 LEG 101300
3 NUT LOCK 5/16-18 NYLON
4 WASHER FLAT 5/16
5 BOLT 5/16 X 1-1/4 HEX HEAD
6 5/16-18 J-BOLT
7 BAG BOLT KIT POLY
×2
Supports de pied
Écrous de blocage
en nylon
Rondelles plates
1 contenant de 14,78 ml
d’apprêt au zinc
Rondelles en plastique
Boulons à tête hexagonale
ITEM DESCRIPTION ILLUSTRATION
1 LEG HIGH SIDE 246
2 LEG 101300
3 NUT LOCK 5/16-18 NYLON
4 WASHER FLAT 5/16
5 BOLT 5/16 X 1-1/4 HEX HEAD
6 5/16-18 J-BOLT
7 BAG BOLT KIT POLY
ITEM DESCRIPTION ILLUSTRATION
1 LEG HIGH SIDE 246
2 LEG 101300
3 NUT LOCK 5/16-18 NYLON
4 WASHER FLAT 5/16
5 BOLT 5/16 X 1-1/4 HEX HEAD
6 5/16-18 J-BOLT
7 BAG BOLT KIT POLY
ITEM DESCRIPTION ILLUSTRATION
1 LEG HIGH SIDE 246
2 LEG 101300
3 NUT LOCK 5/16-18 NYLON
4 WASHER FLAT 5/16
5 BOLT 5/16 X 1-1/4 HEX HEAD
6 5/16-18 J-BOLT
7 BAG BOLT KIT POLY
ITEM DESCRIPTION ILLUSTRATION
1 LEG HIGH SIDE 246
2 LEG 101300
3 NUT LOCK 5/16-18 NYLON
4 WASHER FLAT 5/16
5 BOLT 5/16 X 1-1/4 HEX HEAD
6 5/16-18 J-BOLT
7 BAG BOLT KIT POLY
ITEM DESCRIPTION ILLUSTRATION
1 LEG HIGH SIDE 246
2 LEG 101300
3 NUT LOCK 5/16-18 NYLON
4 WASHER FLAT 5/16
5 BOLT 5/16 X 1-1/4 HEX HEAD
6 5/16-18 J-BOLT
7 BAG BOLT KIT POLY
×2 ×12 ×2
×6 ×6
KEYS
ZINC PRIMER
VINYL TAPE
KEYS
ZINC PRIMER
VINYL TAPE
5/16-18 NYLON
LOCK NUT
5/16 FLAT WASHER
5/16 FLAT WASHER
5/16 FLAT WASHER
5/16 FLAT WASHER
5/16 FLAT WASHER
3/8 HOLE (TYPICAL)
T3/8 HOLE
3/8 HOLE (TYPICAL)
“J” BOLT
5/16-18 HEX HEAD BOLT
5/16-18 HEX HEAD BOLT
5/16-18 NYLON
LOCK NUT
5/16-18 NYLON LOCK NUT
3
OPTIONAL DRILLING METHOD
5/16 WASHER
5/16 WASHER
5/16 NUT
5/16 NUT
BED LIP
TRUCK BOX
NYLON WASHER (IF NECESSARY)