HDO2200 DLP™ Projector Users Manual v1.
Copyright This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author. © Copyright 2012 Disclaimer The information in this document is subject to change without notice.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall Important Safety Information Important: It is strongly recommended that you read this section carefully before using the projector. These safety and usage instructions will ensure that you enjoy many years of safe use of the projector. Keep this manual for future reference. Symbols Used Warning symbols are used on the unit and in this manual to alert you of hazardous situations.
PPrreeffaaccee Projector Installation Notice Place the projector in a horizontal position The tilt angle of the projector should not exceed 15 degrees, nor should the projector be installed in any way other than the desktop and ceiling mount, otherwise lamp life could decrease dramatically. Allow at least 50 cm clearance around the exhaust vent. Ensure that the intake vents do not recycle hot air from the exhaust vent.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall Replacing the Lamp Replacing the lamp can be hazardous if done incorrectly. See Replacing the Projection Lamp on page 37 for clear and safe instructions for this procedure. Before replacing the lamp: Unplug the power cord. Allow the lamp to cool for about one hour. Caution: In rare cases the lamp bulb may burn out during normal operation and cause glass dust or shards to be discharged outward from the rear exhaust vent.
PPrreeffaaccee Table of Contents GETTING STARTED .......................................................................................................................................................... 1 PACKING CHECKLIST ........................................................................................................................................................... 1 VIEWS OF PROJECTOR PARTS .........................................................................................................
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall SPECIFICATIONS............................................................................................................................................................. 46 SPECIFICATIONS ................................................................................................................................................................. 46 PROJECTION DISTANCE VS. PROJECTION SIZE ............................................................
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall GETTING STARTED Packing Checklist Carefully unpack the projector and check that the following items are included: DLP PROJECTOR REMOTE CONTROL (WITH TWO AAA BATTERIES) VGA CABLE CD-ROM (THIS USER’S MANUAL) POWER CORD WARRANTY CARD Contact your dealer immediately if any items are missing, appear damaged, or if the unit does not work.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall Views of Projector Parts Front-right View 1 ITEM 2 3 4 LABEL 56 7 DESCRIPTION 1. Height-adjuster button Push to release height adjuster 2. Height adjuster Adjusts level of projector 3. Lens Projection Lens 4. IR receiver Receive IR signal from remote control 5. Focus ring Focuses the projected image 6. Zoom ring Enlarges the projected image 7. Function keys See Top view—On-screen Display (OSD) buttons and LEDs.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall Top view—On-screen Display (OSD) buttons and LEDs ITEM 1. LABEL (Power button) DESCRIPTION Turns the projector On or Off. 2. BLANK Displays a blank screen and mutes audio 3. ◄ (Left cursor) / Volume- Navigates and changes settings in the OSD Quick Menu – For Volume 4. Enter Enter or confirm highlighted OSD menu item 5. MENU Opens and exits OSD menus 6.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall Rear view ITEM 1. LABEL AC IN 2. DESCRIPTION Connect the POWER CABLE (USB) SEE PAGE: 11 For servicing purpose only 3. COMPONENT IN Connect a component video enabled device 4. S-VIDEO IN Connect the S-VIDEO CABLE from a video device 5. VIDEO IN Connect the COMPOSITE CABLE from a video device 6. VGA OUT Connect the RGB CABLE to a display 7. VGA IN Connect the RGB CABLE from a computer 8.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall Bottom view ITEM LABEL DESCRIPTION SEE PAGE: 1. Tilt adjustor Rotate adjuster lever to adjust angle position. 2. Ceiling support holes Contact your dealer for information on mounting the projector on a ceiling 3. Height adjustor Adjuster drops down when adjuster button is pushed. 4. Height adjustor button Push to release adjustor. 13 13 Note: When installing, ensure that you use only UL Listed ceiling mounts.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall Remote Control Parts Important: 1. Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency fluorescent lights can disrupt remote control operation. 2. Be sure nothing obstructs the path between the remote control and the projector. If the path between the remote control and the projector is obstructed, you can bounce the signal off certain reflective surfaces such as projector screens. 3.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall ITEM LABEL DESCRIPTION SEE PAGE: 1. IR transmitter Transmits signals to projector 2. Status LED Lights when the remote control is used 3. Laser Press to operate the on-screen pointer 4. Up Up arrow when connected through USB to a PC (Not available in this series) 5. Right Right arrow when connected through USB to a PC (Not available in this series) 6.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall Remote Control Operating Range The remote control uses infrared transmission to control the projector. It is not necessary to point the remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or the rear of the projector, the remote will function well within a radius of about 7 meters (23 feet) and 15 degrees above or below the projector level.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall SETUP AND OPERATION Inserting the Remote Control Batteries 1. 2. 3. Remove the battery compartment cover by sliding the cover in the direction of the arrow. Insert the battery with the positive side facing up. Replace the cover. Caution: 1. Only use AAA batteries (Alkaline batteries are recommended). 2. Dispose of used batteries according to local ordinance regulations. 3.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall Connecting Input Devices A PC or notebook computer and video devices can be connected to the projector at the same time. Video devices include DVD, VCD, and VHS players, as well as movie camcorders and digital still cameras. Check the user manual of the connecting device to confirm it has the appropriate output connector.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall Starting and Shutting down the Projector 1. 2. 3. Connect the power cord to the projector. Connect the other end to a wall outlet. The POWER LED will be on. Turn on the connected devices. Ensure the POWER LED displays a solid blue and not a flashing blue. Then press the POWER button to turn on the projector. The projector splash screen displays and connected devices are detected. 4.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall 5. When the POWER OFF window appears, press on the control panel or on the remote control. The projector turns off. Caution: Do not unplug the power cord until the READY LED stops flashing–indicating the projector has cooled down.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall Adjusting the Projector Level Take note of the following when setting up the projector: • The projector table or stand should be level and sturdy. • Position the projector so that it is perpendicular to the screen. • Remove the Back Foot Holder on the rear adjuster foot before adjusting the projection angle. • Ensure the cables are in a safe location. You could trip over them. 1.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall Adjusting the Zoom ring, Focus and Keystone 1. 2. 3. Use the Image-zoom control (on the projector only) to resize the projected image and screen size . Use the Image-focus control (on the projector only) to sharpen the projected image . Use the KEYSTONE buttons (on the projector or the remote control) to correct image-trapezoid (wider top or bottom) effect. Remote control and OSD panel 4. The keystone control appears on the display.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall Adjusting the Volume 1. 2. 3. Press the Volume +/buttons on the remote control. The volume control appears on the display. Press the Left or Right Cursor buttons on the keypad to adjust Volume +/-. Press the MUTE button to turn off the volume (This feature is available only on the remote).
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall ON-SCREEN DISPLAY (OSD) MENU SETTINGS OSD Menu Controls The projector has an OSD that lets you make image adjustments and change various settings. Navigating the OSD You can use the remote control cursor buttons or the buttons on the top of the projector to navigate and make changes to the OSD. The following illustration shows the corresponding buttons on the projector. 1. To enter the OSD, press the MENU button. 2. There are six menus.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall Setting the OSD Language Set the OSD language to your preference before continuing. 1. Press the MENU button. Press the cursor ◄► button to navigate to SETUP>>Basic. 2. Press the cursor ▲▼ button until Language is highlighted. 3. Press the cursor ◄► button until the language you want is selected. 4. Press the MENU button to close the OSD.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall OSD Menu Overview Use the following illustration to quickly find a setting or determine the range for a setting.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall PICTURE>>Basic Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the PICTURE>>Basic menu. Press the cursor ▲▼ button to move up and down in the PICTURE>>Basic menu. Press ◄► to change values for settings. Note: Customizing the settings in PICTURE>>Basic menu is only available in User 1/ 2/ 3 mode. ITEM DESCRIPTION Display Mode Press the cursor ◄► buttons to set the Display Mode.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall PICTURE>>Advanced Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the PICTURE>>Advanced menu. Press the cursor ▲▼ button to move up and down in the PICTURE>>Advanced menu. Press ◄► to change values for settings. ITEM DESCRIPTION Noise Reduction Press the cursor ◄► button to adjust the Noise Reduction. Color Temperature Press the cursor ◄► button to set the Color Temperature.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall HSG Adjustment Press the ENTER button to enter the HSG Adjustment sub menu. ITEM DESCRIPTION Primary Color Press the ◄► buttons to set the Primary Color. Notes: There are six sets (R/ G/ B/ C/ M/ Y) of colors to be customized. Hue Press the ◄► buttons to adjust the Hue. Saturation Press the ◄► buttons to adjust the Saturation. Gain Press the ◄► buttons to adjust the Gain.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall DISPLAY Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the DISPLAY menu. Press the cursor ▲▼ button to move up and down in the DISPLAY menu. Press ◄► to change values for settings. ITEM DESCRIPTION Aspect Ratio Press the cursor ◄► button to set the Aspect Ratio. (Range: Auto/ 16:9/ 4:3/ Letter Box/ Real) Keystone Press the cursor ◄► button to adjust the Keystone.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall PC Detail Adjustment Press the ENTER button to enter the PC Detail Adjustment sub menu. Note: Customizing the settings in PC Detail Adjustment menu is only available when PC input source (analog RGB) is selected. ITEM DESCRIPTION Auto Press the ENTER/AUTO button on the control panel or the ENTER/AUTO button on the remote control to automatically adjust frequency, phase, and position.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall SETUP>>Basic Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the SETUP>>Basic menu. Press the cursor ▲▼ button to move up and down in the SETUP>>Basic menu. Press ◄► to change values for settings. ITEM DESCRIPTION Language Press the cursor ◄► buttons to select a different localization menu.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall Menu Settings Press the ENTER button to enter the Menu Settings sub menu. ITEM DESCRIPTION Menu Position Press the ◄► buttons to select from five OSD locations: Top-Left/ Top-Right/ Center/ Bottom-Left/ Bottom-Right. Menu Transparency Press the ◄► buttons to set the OSD transparency. (Range: 0 ~ 10) Menu Display Time Press the ◄► buttons to set the Menu Display timer before the OSD times out.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall Lan Control Settings Press the ENTER button to enter the Lan Control Settings sub menu. ITEM DESCRIPTION Control By Press the ◄► buttons to select projector remote command control. (Range: RS232/ RJ45) Network State Press the ENTER button to enter the Network State sub menu. See Network State on page 26. Network State ITEM Network State DESCRIPTION Displays the network connection status. Press ◄► to turn DHCP On or Off.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall For simplicity and ease of operation, the projector provides diverse networking and remote management features. The LAN/RJ45 function of the projector through a network, such as remotely manage: Power On/Off, Brightness and Contrast settings. Also, projector status information, such as: Video-Source, SoundMute, etc. 1. Connect an RJ45 cable to RJ45 ports on the projector and the PC (Laptop). 2.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall 3. Right-click on Local Area Connection, and select Properties. 4. In the Properties window, select the General tab, and select Internet Protocol (TCP/IP). 5. Click Properties.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall 6. Click Use the following IP address and fill in the IP address and Subnet mask, then click OK. 7. Press the Menu button on the projector. 8. Select OSD ´ SETUP ´ Network ´ Enabled. 9. After getting into Network, input the following: ` DHCP: Off ` IP Address: 10. 10. 10. 10 ` Subnet Mask: 255.255.255.0 ` Gateway: 0.0.0.0 ` DNS Server: 0.0.0.0 10. Press (Enter) / ► to confirm settings. 11.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall (Enter) / ►. 13. Press The projector is setup for remote management. The LAN/RJ45 function displays as follows.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall For more information, please visit http://www.crestron.com/.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall SETUP>>Advanced Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the SETUP>>Advanced menu. Press the cursor ▲▼ button to move up and down in the SETUP>>Advanced menu. ITEM Audio DESCRIPTION Press the ENTER button to enter the Audio sub menu. See Audio on page 33. Lamp Press the ENTER button to enter the Lamp sub menu. See Lamp on page 33. HDMI Press the ENTER button to enter the HDMI sub menu.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall Audio Press the ENTER button to enter the Audio sub menu. ITEM DESCRIPTION Volume Press the ◄► buttons to adjust the audio Volume. Bass Press the ◄► buttons to adjust the audio Bass. Treble Press the ◄► buttons to adjust the audio Treble. Mute Press the ◄► buttons to turn on or off the speaker. AGC Press the ◄► buttons to turn on or off the AGC setting. Reset Press the ENTER button to reset all settings to default values.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall HDMI Press the ENTER button to enter the HDMI sub menu. ITEM DESCRIPTION HDMI Format Press the ◄► buttons to select from three HDMI display formats: Auto/ PC signal/ Video signal. HDMI Amplifier Gain Press the ◄► buttons to adjust HDMI Amplifier Gain. Closed Caption Press the ENTER button to enter the Closed Caption sub menu. ITEM DESCRIPTION Closed Caption Enable Press the ◄► buttons to turn on or off Closed Caption.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall Presentation Timer The Presentation Timer function can indicate the presentation time on the screen to help you achieve better time management when giving presentations. ITEM DESCRIPTION Timer Press the cursor ◄► button to enable or disable presentation timer. Timer Period Press the cursor ◄► button to select timer period (1 ~ 60 minutes) Timer Reset Press (Enter) / ► to reset the timer settings.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall STATUS Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the STATUS Menu. ITEM DESCRIPTION Source Displays the activated input source. Resolution Displays the native resolution of input source. Lamp Hour Displays the number of hours the lamp has been in use. Firmware Version Displays the firmware version of the projector. Note: Status displayed in this menu is for viewing only and cannot be edited.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall MAINTENANCE AND SECURITY Replacing the Projection Lamp The projection lamp should be replaced when it burns out. It should only be replaced with a certified replacement part, which you can order from your local dealer. Important: a. The projection lamp used in this product contains a small amount of mercury. b. Do not dispose this product with general household waste. c.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall 3. Remove the three screws from the lamp module. 4. Lift the module handle up. 5. Pull firmly on the module handle to remove the lamp module. 6. Reverse steps 1 to 5 to install the new lamp module. While installing, align the lamp module with the connector and ensure it is level to avoid damage. Note: The lamp module must sit securely in place and the lamp connector must be connected properly before tightening the screws.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall Cleaning the Projector Cleaning the projector to remove dust and grime will help ensure trouble-free operation. Warning: 1. Be sure to turn off and unplug the projector at least 30 minutes before cleaning. Failure to do so could result in a severe burn. 2. Use only a dampened cloth when cleaning. Do not allow water to enter the ventilation openings on the projector. 3.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall Using the Kensington® Lock If you are concerned about security, attach the projector to a permanent object with the Kensington slot and a security cable. Note: Contact your vendor for details on purchasing a suitable Kensington security cable. The security lock corresponds to Kensington’s MicroSaver Security System. If you have any comment, contact: Kensington, 2853 Campus Drive, San Mateo, CA 94403, U.S.A. Tel: 800-535-4242, http://www.Kensington.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall TROUBLESHOOTIN G Common problems and solutions These guidelines provide tips to deal with problems you may encounter while using the projector. If the problem remains unsolved, contact your dealer for assistance. Often after time spent troubleshooting, the problem is traced to something as simple as a loose connection. Check the following before proceeding to the problem-specific solutions.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall LED Error Messages POWER LED BLINK READY LED BLINK TEMP LED BLINK Lamp Ready ON ON OFF Start ON OFF OFF Cooling ON FLASHING OFF Over temperature OFF OFF ON Thermal Break Sensor error 4 4 OFF Lamp error 5 OFF OFF Lamp End of lamp life detected 5 3 OFF Burner Fan error 6 1 OFF Lamp Fan error 6 2 OFF Power Fan error 6 3 OFF DMD Fan error 6 4 OFF Case Open 7 OFF OFF DMD error 8 OFF OFF Color wheel er
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall Problem: The image is flat with no contrast Adjust the Contrast setting on the Image menu of the OSD. Problem: The color of the projected image does not match the source image. Adjust the Color Temperature and Gamma settings on the Image menu of the OSD. Lamp Problems Problem: There is no light from the projector 1. Check that the power cable is securely connected. 2. Ensure the power source is good by testing with another electrical device. 3.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall Audio Problems Problem: There is no sound 1. Adjust the volume on the remote control. 2. Adjust the volume of the audio source. 3. Check the audio cable connection. 4. Test the source audio output with other speakers. 5. Have the projector serviced. Problem: The sound is distorted 1. Check the audio cable connection. 2. Test the source audio output with other speakers. 3. Have the projector serviced.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall HDMI Q & A Q. What is the difference between a “Standard” HDMI cable and a “High-Speed” HDMI cable? Recently, HDMI Licensing, LLC announced that cables would be tested as Standard or HighSpeed cables. ․Standard (or “category 1”) HDMI cables have been tested to perform at speeds of 75Mhz or up to 2.25Gbps, which is the equivalent of a 720p/1080i signal.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall SPECIFICATIONS Specifications Model HDO2200 TI DLP DMD 0.65” Display type 1920 x 1080 Native Resolution 3.4 kg (7.5 lbs) Weight 1 meters ~ 10 meters Projection distance 23.5" ~ 282.3" Projection screen size Manual Focus/Manual Zoom Projection lens 1.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall Image Height Projection Distance vs. Projection Size Projection Distance and Size Table HJDO2200 (16 x 9 SCREEN) IMAGE DIAGONAL （INCH） IMAGE WIDTH (INCH) PROJECTION DISTANCE （MM） FROM IMAGE HEIGHT (INCH) PROJECTION DISTANCE （MM） TO OFFSET-A ( MM ) 40 34.9 19.6 1408.0 1682.5 74.7 60 52.3 29.4 2112.0 2523.7 112.1 70 61 34.3 2464.0 2944.4 130.8 72 62.8 35.3 2534.4 3028.5 134.5 80 69.7 39.2 2816.0 3365.0 149.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall Timing Mode Table The projector can display several resolutions. The following table outlines the resolutions that can be displayed by the projector. RESOLUTION H-SYNC (KHZ) NTSC — 15.734 60.0 O — － － PAL/SECAM — 15.625 50.0 O — － － 720 x 400 37.9 85.0 — — O O 640 x 480 31.5 60.0 — — O O 640 x 480 37.9 72.8 — — O O 640 x 480 37.5 75.0 — — O O 640 x 480 43.3 85.0 — — O O 800 x 600 35.2 56.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall SIGNAL HDTV RESOLUTION H-SYNC (KHZ) V-SYNC COMPOSITE RGB HDMI TM COMPONENT (HZ) / S-VIDEO (ANALOG) (DIGITAL) 720p 37.5 50.0 — O — O 720p 45.0 60.0 — O — O 1080i 33.8 60.0 — O — O 1080i 28.1 50.0 — O — O 1080p 67.5 60.0 — O — O 1080p 56.3 50.
D DLLPP PPrroojjeeccttoorr— —U Usseerr’’ss M Maannuuaall Projector Dimensions – 50 –
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall REGULATORY COMPLIANCE FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
© 2012 Knoll Systems. All Rights Reserved, All specifications subject to change without notice.
