Specification Sheet

206 Series Folding L-Brackets
5. INSTALLATION
For maximum loading capacity, brackets should be mounted
directly to wall studs, which are generally found on 16" centers. Prior to
drilling all holes, check to be sure that the bracket is
vertically level.
Attach one bracket to wall stud by fastening one #10 x 2" screw
through the top mounting hole in bracket. Use a level to position the
second bracket at the same height as the fi rst bracket and fasten it to
a wall stud using one 2" screw through the top mounting hole.
Center the shelf on the brackets. Fasten a #8 screw through rear
most mounting hole on each bracket. Confi rm that the shelf folds
properly and adjust position of brackets if necessary.
Finish securing the brackets to the wall by fastening #10 x 2"
screws through the second top mounting hole and through one of two
bottom mounting holes.
Finish securing the brackets to the shelf by fastening #8 screws
through the second rear mounting hole and through one of two front
mounting holes.
6. AVAILABILITY AND COST
Availability: Knape & Vogt
TM
(KV
®
) products are available from
stocking distributors and through KV
®
Representatives worldwide.
Cost: Current pricing is available from area KV
®
Representatives.
Please call for the nearest representative: [phone].
7. WARRANTY
Limited Lifetime Warranty: Knape & Vogt offers its standard
Limited Lifetime Warranty to the initial purchaser of commercial
products. This warranty covers defects in materials and workmanship
which occur during normal use, and the remedy is limited to repair or
replacement of defective products, at KV's option. Certain types of
defects and damage are excluded from warranty coverage, costs and
expenses are not covered, and additional restrictions apply. A copy of
the Limited Lifetime Warranty, with all warranty details, limitations and
disclaimers, is available on the Customer Care Connection location at
www.kv.com or from KV Customer Service, 2700 Oak Industrial Drive,
Grand Rapids, MI 49505, [phone].
8. MAINTENANCE
206 Series Folding L-Brackets require no maintenance. Inspect
for proper fi t periodically and adjust when necessary. Replace as
required or recommended by application.
9. TECHNICAL SERVICES
Knape & Vogt
TM
and area represen tatives can assist with any
application. For further information, or for the name of the
representative nearest you, please call Knape & Vogt
TM
Customer
Service: [phone] or visit our website at: www.kv.com.
10. FILING SYSTEMS
Additional product information, data sheets, application sheets,
and a full catalog are available upon request from Knape & Vogt
TM
.
1. PRODUCT NAME
206 Series Folding L-Brackets.
For heavy-duty storage and work surface applications when limitations
and/or fl exibility in space is critical.
2. MANUFACTURER
Knape & Vogt Manufacturing Company
2700 Oak Industrial Dr. NE, Grand Rapids, MI USA 49505-6026
[phone] | www.kv.com
3. PRODUCT DESCRIPTION
Basic Use: 206 Series Folding L-Brackets are manufactured for
heavy-duty storage and work surface applications when limitations
and/or fl exibility in space is critical, such as retail stores, grocery
stores, warehouses, industrial, repair garages, maintenance storage,
business offi ce storage, and residential storage. Mounts to most
wall types.
Composition and Materials:
12" (300mm): 16 gauge cold rolled steel
16" (400mm): 14 gauge cold rolled steel
Sizes:
12" (300mm): (11.81") length x 200mm (7.87") height
16" (400mm): (15.75") length x 270mm (10.63") height
Width: 12" (300mm): 15mm (6.59"); 16" (400mm): 20mm (0.79")
Finishes: Zinc & White (powder-coat).
4. TECHNICAL DATA
Applicable Standards: Brackets are tested to meet or exceed
ANSI performance standards as established by BHMA.
These load limits are intended to be used as general guidelines
only, and no warranty — expressed or implied — is made by
Knape & Vogt.
Results were obtained by laboratory testing in accordance with
ANSI/ BHMA A156.9-2003 performance standard. (Load ratings based
on brackets being mounted on 16" centers. Wider spacing will result
in reduced load capacity.) Actual use conditions will typically result in
lower load capacity than laboratory conditions.
Representative testing in a fully confi gured application is the only
way to assure proper performance, durability, and safety. Contact KV
for verifi cation testing service of your specifi c application.
Environmental Considerations:
Environment: Excessive humidity, salts, or other chemical agents
can corrode the fi nish and attack metal or plastic components.
Fastening: Inadequate or incorrect fasteners can result in the
bracket pulling loose and causing damage.
Alignment: Improper bracket alignment can result in a shelving
system that is ineffective and unsafe.
Knape & Vogt
®
, 2700 Oak Industrial Drive NE, Grand Rapids, MI USA 49505 | P 616.459.3311 | 800.253.1561 | F 616.459.3290 | www.kv.com
©2009 Knape & Vogt. KV and the KV logo are trademarks of Knape & Vogt. Printed in U.S.A. OL2236/1209
Knape & Vogt reserves the right to change product specifi cations at any time without notice and without incurring responsibility for existing units.
This information conforms to editorial style prescribed by The Construction Specifi cations Institute.
BHMA
Knape & Vogt shelving products follow the
ANSI testing standards established by BHMA.
206 Series
Folding L-Bracket
Dimensions
Size A B C
12"
300mm 300mm 200mm 15mm
16"
400mm 400mm 270mm 20mm