JOBSITE STORAGE SOLUTIONS ALWAYS ON THE JOB™ INSTALLATION MANUAL 118-01 DATAVAULT 118-02 DATAVAULT - BARE Werner Co. 724-588-2000 93 Werner Rd.
NOTICE ATTENTION: PLEASE READ AND UNDERSTAND ALL INSTRUCTIONS AND WARNINGS BEFORE ASSEMBLING, INSTALLING OR USING THIS PRODUCT. Tools Required • 9/16” SOCKET • 9/16” WRENCH • 5/16” SOCKET • 7/16” SOCKET • 7/16” WRENCH • SCREWDRIVER, STRAIGHT BLADE • SCREWDRIVER, PHILLIPS HEAD Parts List • MODEL 500 POWER CREW * QTY. 1 • MODEL 497 LIFT BRACKETS* QTY. 1 • BRACKETS, SCREEN MTG. QTY. 2 Bolt Kit #32-1180 • BOLT, M4 X18MM PHILLIPS HEAD QTY. 4 • BOLT, M4 X30MM PHILLIPS HEAD QTY.
Data Vault USER INSTRUCTIONS Contents I. Installing A Large Screen...................................................................... 4 II. 3 Position Hatch Feature......................................................................... 6 a. Working Position.......................................................................................................6 b. Open Position...........................................................................................................6 c.
CAUTION Any modification or unintended use of this product shall immediately void all manufactures warranties. Manufacture disclaims all liability for injuries to persons or property resulting from any modification to, or unintended use of this product. CAUTION Prior to drilling to keep debris out of your eyes, always wear protective eye wear. Failure to heed may result to death or serious injury. I. Assembly of TV/Monitor and TV/Monitor Protector a. Take the TV/monitor from the shipping packaging b.
Data Vault USER INSTRUCTIONS g. Remove the Velcro straps from the TV protector h. Slide the TV protector onto the TV i. Tighten the Velcro straps down (FIG. 3) j. Lift the TV/Protector assembly k. Place TV, mounting plate to mounting plate holder l. Assemble the bolt to the back of the mount (FIG. 4) m. Connect the HDMI cables, on the left side of the TV (FIG. 5) n.
o. Pull the TV mount out and push to one side to be able to access the mounting plate holder p. Adjust the mounting plate to vertical position and tighten the two nuts on each side (FIG. 6). II. 3 Position Hatch Feature The keyboard hatch can be positioned in 3 places, working, open and closed. a. Working Position With the rod placed fully forward, the keyboard will be level, while still providing a flat work surface above. b.
Data Vault USER INSTRUCTIONS c. Closed Position Lift rod out of the notch and hold rod in location shown, slide the rod rearward to allow the hatch to close. III. Lockable Hatch Hatch can be locked to protect valuables while momentarily away. Simply attach any padlock through the locking tab and loop of the rod. IV. Installing A Printer (printer not included in 118-02) a. Install lose drawer into pre-installed drawer slides. Refer to drawer removal instructions on page 10. ENGLISH b.
V. Installing USB Switch (not included in 118-02) Install USB switch in central compartment. Attach 2 USB-BM cables into switch. a. Install USB hub, connecting USB hub computer port/connector into USB switch. b. Plug USB-AM cable (from printer) into USB hub. ENGLISH c. Other computer USB devices such as a keyboard and mouse may be installed at this time.
Data Vault USER INSTRUCTIONS VI. Installing Power Strips (not included in 118-02) a. Install both power strips into the 118-01. Place one in the central compartment and route the cord through the cable channel to the lower compartment. Place the second in the lower compartment. b. Prior to installing the UPS power system, it needs to be charged for several hours. c. Install UPS device into right lower compartment on shelf. d. Plug the UPS power system into one of the GFCI slots in the powerstrip. e.
VIII. Drawer Adjustment: If you need to move any of the bottom drawers, to fit your printer or computer, follow these instructions: a. Drawer Removal and Installation 1. To remove a drawer (FIG. 8), pull the drawer out till it stops. Notice the locking levers located inside the track that is attached to the drawer. Lift lever (A) while pressing down on the right lever (B). Pull drawer clear of the sides. 2.
Data Vault USER INSTRUCTIONS c. Drawer Retention 1. Install 14-20 x 5/8” hex head bolt on inside of the front, 2 places each drawer. Fasten with 1/4-20 whiz nut. 2. This will prevent the drawer from bouncing out when being transported. IX. Installing Straps C DRAWER SLIDE 1/4-20 x 5/8” BOLT DRAWER 1/4-20 WHIZ NUT Straps have been provided to secure printer and power supply. Simply route strap through slots and pull until snug.
KnaackLLC ATTN:Warranty Claims 420 E. Terra Cotta Avenue Crystal Lake, IL 60014 www.knaack.com If you have any questions, please call toll free at 1-800-456-7856. ©2013 Knaack LLC PN14-0056 ©2016 Werner Co.
