JOBSITE STORAGE SOLUTIONS ALWAYS ON THE JOB™ INSTALLATION MANUAL 118-01 DATAVAULT 118-02 DATAVAULT - BARE Werner Co. 724-588-2000 93 Werner Rd.
NOTICE ATTENTION: PLEASE READ AND UNDERSTAND ALL INSTRUCTIONS AND WARNINGS BEFORE ASSEMBLING, INSTALLING OR USING THIS PRODUCT. Tools Required • 9/16” SOCKET • 9/16” WRENCH • 5/16” SOCKET • 7/16” SOCKET • 7/16” WRENCH • SCREWDRIVER, STRAIGHT BLADE • SCREWDRIVER, PHILLIPS HEAD Parts List • MODEL 500 POWER CREW * QTY. 1 • MODEL 497 LIFT BRACKETS* QTY. 1 • BRACKETS, SCREEN MTG. QTY. 2 Bolt Kit #32-1180 • BOLT, M4 X18MM PHILLIPS HEAD QTY. 4 • BOLT, M4 X30MM PHILLIPS HEAD QTY.
Data Vault USER INSTRUCTIONS Contents I. Installing A Large Screen...................................................................... 4 II. 3 Position Hatch Feature......................................................................... 6 a. Working Position.......................................................................................................6 b. Open Position...........................................................................................................6 c.
CAUTION Any modification or unintended use of this product shall immediately void all manufactures warranties. Manufacture disclaims all liability for injuries to persons or property resulting from any modification to, or unintended use of this product. CAUTION Prior to drilling to keep debris out of your eyes, always wear protective eye wear. Failure to head may result to death or serious injury. I. Installing A Large Screen a. Using the 5/16” socket remove the four #10-24 x 3/4” Hex head screws.
Data Vault USER INSTRUCTIONS c. Once screen has been mounted to the brackets, attach HDMI (2) and VGA(1) cables to the back of the screen (FIG.3). d. Plug screen and fan power cords into extension cord (SEE FIG. 4). Route extension cord through cord pass through in back of enclosure. After enclosure installation, route extension cord through cable channel at rear of the 118 to the central compartment and plug into power strip. Switch on powerstrip may be turned on and off to control fan and screen power.
g. Attach screen mounting brackets through the coresponding holes in the bottom of the enclosure using two 1/420 x 5/8 bolts and 1/4-20 whiz nuts. II. 3 Position Hatch Feature The keyboard hatch can be positioned in 3 places, working, open and closed. a. Working Position With the rod placed fully forward, the keyboard will be level, while still providing a flat work surface above. b.
Data Vault USER INSTRUCTIONS c. Closed Position Lift rod out of the notch and hold rod in location shown, slide the rod rearward to allow the hatch to close. III. Lockable Hatch Hatch can be locked to protect valuables while momentarily away. Simply attach any padlock through the locking tab and loop of the rod. IV. Filtered Fan Motor CAUTION When fan is in use, the upper compartment doors must also be open to cool efficiently.
a. Filter is located to the lower right side of enclosure. b. Un-snap filter cover as shown c. Remove cover and remove filter. Clean filter with water and squeeze out excess water before installing filter back onto fan. To avoid damaging the fan and screen, never run fan without the filter installed. ENGLISH V. Installing A Printer (printer not included in 118-02) a. Install lose drawer into pre-installed drawer slides. Refer to drawer removal instructions on page 10.
Data Vault USER INSTRUCTIONS b. Plug the power cord and USB connection into back of printer and place printer on upper shelf in left compartment. Route the power cable through center dividing walls into compartment on right side. Plug power into UPS in the surge protector without battery backup. VI. Installing USB Switch (not included in 118-02) Install USB switch in central compartment. Attach 2 USB-BM cables into switch. a. Install USB hub, connecting USB hub computer port/connector into USB switch.
VII. Installing Power Strips (not included in 118-02) a. Install both power strips into the 118-01. Place one in the central compartment and route the cord through the cable channel to the lower compartment. Place the second in the lower compartment. b. Prior to installing the UPS power system, it needs to be charged for several hours. c. Install UPS device into right lower compartment on shelf. d. Plug the UPS power system into one of the GFCI slots in the powerstrip. e.
Data Vault USER INSTRUCTIONS a. Drawer Removal and Installation 1. To remove a drawer (FIG. 8), pull the drawer out till it stops. Notice the locking levers located inside the track that is attached to the drawer. Lift lever (A) while pressing down on the right lever (B). Pull drawer clear of the sides. 2. To replace a drawer, simply insert the drawer slide into the cabinet slide and close the drawer completely. The mechanism will automatically latch. b. Drawer Slide Install 1. Take one slide (FIG.
KnaackLLC ATTN:Warranty Claims 420 E. Terra Cotta Avenue Crystal Lake, IL 60014 www.knaack.com If you have any questions, please call toll free at 1-800-456-7856. ©2013 Knaack LLC PN14-0056 ©2015 Werner Co.
