Document NO. Project Code Project Name Subject KMWI-A61-E210 L15LT044Z INNER ANTENNA NODE Revision NO. Revised Date A1 2017.05.02 INNER ANTENNA NODE Manual Page Written by Checked by Approved by 1 / 14 BJ KIM INNER ANTENNA NODE Test Manual 2017. 05. 02. KN-연-062 (15.12.
Document NO. Project Code Project Name Subject KMWI-A61-E210 L15LT044Z INNER ANTENNA NODE Revision NO. Revised Date A1 2017.05.02 INNER ANTENNA NODE Manual Page Written by Checked by Approved by 2 / 14 BJ KIM Document Revision History No 1 Description -. initial KN-연-062 (15.12.21)-0 Author BJ KIM Page REV. NO A0 Revised Date 2017. 05.
Document NO. Project Code Project Name Subject KMWI-A61-E210 L15LT044Z INNER ANTENNA NODE Revision NO. Revised Date INNER ANTENNA NODE Manual A1 2017.05.02 Page Written by Checked by Approved by 3 / 14 BJ KIM INDEX DOCUMENT REVISION HISTORY ........................................................................................................................ 2 1. INT NODE TEST AND TEST PROGRAM D/L USING THE POWER SUPPLY 오류! 책갈피가 정의되어 있 지 않습니다. 2. IQ NXN SETTING...............................
Document NO. Project Code Project Name Subject 1. KMWI-A61-E210 L15LT044Z INNER ANTENNA NODE Revision NO. Revised Date A1 2017.05.02 INNER ANTENNA NODE Manual Page Written by Checked by Approved by 4 / 14 BJ KIM INT NODE TEST AND Test Program D/L Using the Power Supply INPUT Power 1-1. - INT NODE is powered by a Power Supply. current consumption check using the Power Supply - Power Supply settings DC15V, 0.5A - INT NODE’s average power consumption is under 0.45W.
Document NO. Project Code Project Name Subject KMWI-A61-E210 L15LT044Z INNER ANTENNA NODE Revision NO. Revised Date A1 2017.05.02 INNER ANTENNA NODE Manual Page Written by Checked by Approved by 5 / 14 BJ KIM Open the RF Test Program to download INT 1-6. MG245X-KMW_IQVIEWER_V22_PA_Rev02.H00 MG245X-KMW_IQVIEWER_V22_PA_Rev02.H01 - 1-7. Download only choose H00 file extension. Download < Download complete message > 1-8. Change into Operating Mode KN-연-062 (15.12.
Document NO. Project Code Project Name Subject KMWI-A61-E210 L15LT044Z INNER ANTENNA NODE Revision NO. Revised Date A1 2017.05.02 INNER ANTENNA NODE Manual Page Written by Checked by Approved by 6 / 14 BJ KIM 2. IQ NxN Test Setting Setting test environment as under figure PC TEM CELL RF IN/OUT USB USB LAN PORT IQ nxn RF CABLE LAN PORT RF1 RF2 LAN CABLE USB CABLE [ ] Block Diagram < Test environment image> 2-1. Connect Ethernet cable to Ethernet socket at IQ NXN device rear.
Document NO. Project Code Project Name Subject KMWI-A61-E210 L15LT044Z INNER ANTENNA NODE Revision NO. Revised Date A1 2017.05.02 INNER ANTENNA NODE Manual Page Written by Checked by Approved by 7 / 14 BJ KIM 2-1. Setting PC's IP as under figure. < PC의 IP Setting > 2-2. Execute IQ signal for Zigbee. And Setting Parameter as under figure. < IQsignal for Zigbee Program Parameter Setting > A. 3. Connect USB to Serial Cable to Z_Deg port(J2). TX Test 3-1.
Document NO. Project Code Project Name Subject KMWI-A61-E210 L15LT044Z INNER ANTENNA NODE Revision NO. Revised Date A1 2017.05.02 INNER ANTENNA NODE Manual Page Written by Checked by Approved by 8 / 14 BJ KIM 3-2. Execute Tera Term - serial port as under figure. : The Top bar ‘Setup’ -> ‘Serial Port ...’ selection < Tera Term’s Serial Port Setting> - Press 'H' key on the keyboard to display the test menu as below.. < KMW TEST MENU > - Press 'C' key on the keyboard and select channel.
Document NO. Project Code Project Name Subject KMWI-A61-E210 L15LT044Z INNER ANTENNA NODE Revision NO. Revised Date A1 2017.05.02 INNER ANTENNA NODE Manual Page Written by Checked by Approved by 9 / 14 BJ KIM 3-3. Execute Tx test using the ‘IQ signal for Zigbee’ PC Program Setting Input Parameters as under figure. - RF Input : Left RF PORT - RF Channel : 20/2450MHz (@ Test Ch. 20CH) - Max Signal Level : 10dBm - Trigger type : signal trigger -.
Document NO. Project Code Project Name Subject KMWI-A61-E210 L15LT044Z INNER ANTENNA NODE Revision NO. Revised Date A1 2017.05.02 INNER ANTENNA NODE Manual Page Written by Checked by Approved by 10 / 14 BJ KIM < Tx test measure > - Compare with the following items to check for defects Items Req'd Spec Remark Transmit Power (Peak Power) ≥5dBm [6.9.5]IEEE802.15.4-2006 Spectrum PSD mask Check [6.5.3.1]IEEE802.15.4-2006 Transmit Center Frequency Tolerance ±40ppm [6.9.4]IEEE802.15.
Document NO. Project Code Project Name Subject KMWI-A61-E210 L15LT044Z INNER ANTENNA NODE Revision NO. Revised Date A1 2017.05.02 INNER ANTENNA NODE Manual Page Written by Checked by Approved by 11 / 14 BJ KIM 4-2. Connect IQnxn's RF2 Channel to device's output. Or Change input parameters(Left RF Port-> Right RF Port) 4-3. Open the ‘zigbee_psdu20.mod’ file Setting ‘A’ section as under figure. (IEEE802.15.
Document NO. Project Code Project Name Subject 4-5. KMWI-A61-E210 L15LT044Z INNER ANTENNA NODE Revision NO. Revised Date A1 2017.05.02 INNER ANTENNA NODE Manual Page Written by Checked by Approved by 12 / 14 BJ KIM Select RF ON/OFF button as under figure, select 'Start' button. then number 1000's Tx data is transmitted to the INT NODE Board.. 4-2. If press '2' on the keyboard, can be check transmitted result.
Document NO. Project Code Project Name Subject KMWI-A61-E210 L15LT044Z INNER ANTENNA NODE Revision NO. Revised Date A1 2017.05.02 INNER ANTENNA NODE Manual Page Written by Checked by Approved by 13 / 14 BJ KIM FCC compliance Information FCC Information to User This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Document NO. Project Code Project Name Subject KMWI-A61-E210 L15LT044Z INNER ANTENNA NODE INNER ANTENNA NODE Manual Revision NO. Revised Date A1 2017.05.02 Page Written by Checked by Approved by 14 / 14 BJ KIM This device is intended only for OEM integrators under the following conditions: 1)The transmitter module may not be co-located with any other transmitter or antenna, 2)OEM shall not supply any tool or info to the end-user regarding to Regulatory Domain change.
