Sheet 1 of 17 Sheet 1 of 17 AICM 1:1 Interface Program Manual - Air Interface Control Monitoring 1:1 Interface Program Manual - 2006. 05. 30 Research & Development Center KMW Inc. Copyright © 2006 KMW Inc.
Sheet 2 of 17 Sheet 2 of 17 ♦ Revision History 1. Preliminary version by Myong Sik Lee. May 30, 2006. Copyright © 2006 KMW Inc.
Sheet 3 of 17 Sheet 3 of 17 05-30-2006 Contents 1. Overview ......................................................................................................................................................... 4 2. System requirements (minimum) ....................................................................................................................... 5 3. Communication Protocol.................................................................................................................
Sheet 4 of 17 Sheet 4 of 17 05-30-2006 1. Overview The AICM 1:1 Interface Program is designed to manage each AICM (Air Interface Control Monitoring) through a RS-232C interface. AICMs are located at BTS inside and they can control and monitor the status of antennas. A user can input the Antenna information, AICM IP Address, Gateway, Subnet Mask and NMS Server IP Address into each AICM through RS-232C communication. Figure 1-1 shows a communication block diagram.
Sheet 5 of 17 Sheet 5 of 17 AICM 1: 1 Interface Program 05-30-2006 AICM Message Request Control, Status ACK Response Control, Status Time Over Retry NACK Retry # 1 Time Over NACK Retry Retry # 2 Time Over NACK Communication Fail Requests and Responses of the program 2. System requirements (minimum) OS: Windows 2000, Windows XP PENTIUM 4: 700MHz RAM: 256MB Display: 1024 * 768 pixel 3. Communication Protocol TCP/IP Protocol : This is not available for the 1:1 interface program.
Sheet 6 of 17 Sheet 6 of 17 05-30-2006 An InstallShield screen A Setup Welcome message Destination Folder selection A Choose Destination Location window Copyright © 2006 KMW Inc.
Sheet 7 of 17 Sheet 7 of 17 A Select Program Folder window A Setup Complete window Getting stated with the program Copyright © 2006 KMW Inc.
Sheet 8 of 17 Sheet 8 of 17 05-30-2006 5. A main window When the user runs the program, A Main window pops up (Figure 5-1). Only one program is able to run at one PC. 1) Menu bar: File, Port, Settings, View, and Help a. File menu: Set Pattern Data, Set Control Data b. Port menu : Port Open, Port Close, Port Set c. Settings menu: Download, Console (Data Log), Input, Set Device, and Set GMT Time d. View menu: Not currently activated. e.
Sheet 9 of 17 Sheet 9 of 17 05-30-2006 Antenna information per sector: Antenna formats are selectively displayed according to the types of antenna installed. There are 4 different types of antenna (Tilting#1, Tilting#2, Steering, and Width). The type and the model are defined in Table 1. A related antenna control button will be activated. Ant. Install LED: A blue LED turns on when an antenna was installed at each sector. If not installed, the LED turns off.
Sheet 10 of 17 Sheet 10 of 17 05-30-2006 Data format Display the TX/RX A Console window 6. An Antenna Information Setting After installing of the AICM properly, a user must set the antenna information. An Input menu A Set Device menu Clicks the Input menu of Figure 6-1. The dialog-box shown in Figure 6-3 pops up. A serial number is determined when a product is shipped. The NMS Application sets ID according to the database.
Sheet 11 of 17 Sheet 11 of 17 Display an ID and the Serial Number, not editable Select an Antenna to be installed or not Select an Antenna type Select an Antenna Model depending on the Antenna type Set ID & Antenna information A Set Input window A user must check this, if not the information will not be updated Set BTS name, maximum 20 characters Set AICM Network Information Set Server IP Address A Set Device window Copyright © 2006 KMW Inc.
Sheet 12 of 17 Sheet 12 of 17 05-30-2006
Antenna Definition List Type Model Tilting 1 AM-X-CB-15-65-00T 0~14 Cellular 800MHz AM-X-CB-15-65-06T 6~20 Cellular 800MHz AM-X-CB-17-65-00T 0~10 Cellular 800MHz AM-X-GB-15-65-00T 0~14 GSM 900MHz AM-X-DB-17-65-00T 0~16 DCS 1800MHz AM-X-PA-17-65-00T 0~16 US PCS AM-X-IB-17-65-00T 0~16 IMT2000 HB-X-ID-16-90-00T 0~15 -30~30 US PCS HB-X-ID-19-65-00T 0~6 -30~30 BROAD BAND HB-X-ID-17-65-00T 0~15 -30~30 BROAD BAND HB-X-ID-19-3Sheet 13 of 17 Sheet 13 of 17 05-30-2006 Antenna Control An Antenna Control window 8. An Antenna pattern data selection When the user points to the Set Pattern Data menu of Figure 8-1, and a dialog box appears (Figure 8-2). The user can select a pattern information file that is matched to each antenna. There are pattern files for EDTA, Hybrid 2Way, 3 Column and Hybrid 3Way up to now. The Set Control Data menu of Figure 8-1 is not necessary for the installation.
Sheet 14 of 17 Sheet 14 of 17 05-30-2006 9. Download A dialog box (Figure 9-2) appears when the user selects a Download menu in Figure 9-1. A Download menu The user points to a binary file (Refer to Figure 9-2) by clicking a “...” button on the right side of Fig 9-2. And a selected file name appears in a downloader (Figure 9-2). A downloading starts by clicking the Download button. The progress rate is displayed in a Download Progress Status column during a download.
Sheet 15 of 17 Sheet 15 of 17 05-30-2006 11. Help menu A dialog box in Figure 11-2 appears when the user selects an About New Aicm menu (Figure 11-1). It has the program version and other information. An About New Aicm menu An About New Aicm window 12. An introduction of AICM equipment Figure 12-1 shows a front panel of AICM equipment and Figure 12-2 shows a rear panel. AICM STATUS PWR TX ALM RX RS-485 COM.
Sheet 16 of 17 Sheet 16 of 17 AC Power Input AC INPUT I 05-30-2006 DC (-48V) Input Antenna connection port FUSE O 100- 240V~ 50/ 60Hz S/ W FUSE α- MOT DC β- MOT γ- MOT Power ON/OFF Switch & Fuse A rear panel AC power Input: AC power input Power ON/OFF Switch: DC power ON/OFF switch FUSE: Over current protection for DC power (-48V), Maximum Current(2A) DC (-48V) power Input: DC power (-48V) input Antenna Connection: SMA ports are connected to each ALPHA, BETA, and GAMMA antenna b
Sheet 17 of 17 Sheet 17 of 17 05-30-2006 3) Step 3 a. Connect a RJ-45 ethernet cable to the Ethernet port of Figure 12-1. AICMs request a TCP/IP connection to the NMS application. b. Check the TCP/IP connection request status at the NMS Application. Refer to the AICM NMS Application manual. Copyright © 2006 KMW Inc.
