Overview of Primary Product

ManualsBrandsKMC Controls ManualsDampers6-1/4" x 5/16" Push-Rod

Table Of Contents

Models

MCP-1020 X YYY

“X” Spring Ranges and Retracted/Extended Torque

(Based on 0 and 20 psi applied, at 90°)

2: 3 to 12 psi; 10/26 in-lbs. (21 to 83 kPa; 1/3 N•m)

3: 5 to 10 psi; 16/32 in-lbs. (34 to 69 kPa; 2/4 N•m)

5: 8 to 13 psi; 26/22 in-lbs. (55 to 90 kPa; 3/2 N•m)

6: 10 to 15 psi; 32/16 in-lbs. (69 to 103 kPa; 4/2 N•m)

8: 4 to 8 psi; 13/38 in-lbs. (28 to 55 kPa; 1/4 N•m)

(MCP-020X is for the actuator alone)

“Y” Linkage

308: with ball joint

311: with 1/2" crank arm

312: with 3/8" crank arm

(Crank Arm Shown)

Features

♦ Gradual or two-position action

♦ Post or right-angle mounting bracket

♦ Fits 1/2" or 3/8" damper shas

♦ Variety of spring ranges, mounting brackets, and

linkages provide exibility

Description

The KMC MCP-1020/020X Series 2" Pneumatic

Damper Actuators are designed to position

automatic air dampers in pneumatically controlled

systems. They may be used for gradual or two-

position applications.

Models are available with right-angle bracket

mounting and several linkage options.

Speciﬁcations and design subject to change without notice.

MCP-1020/020X Series

2" Pneumatic Damper Actuators

Accessories and Repair Parts

CMC-1001 Non-metallic positive positioner

CMC-1002 Metal positive positioner

VTD-0803 Ball joint, 1/4-20 male x 5/16-24 female

for use on end of actuator shas

VTD-0804 Ball joint, 1/4-20 male x 1/4-20 female for

use with VTD-1400 series crank arms

VTD-0903 Right-angle bracket for MCP-1020 series

VTD-1414 3-hole crank arm for 3/8" damper shas

VTD-1415 3-hole crank arm for 1/2" damper shas

VTD-1630 Push rod, 5/16 x 6-1/4"

VTD-9422 Replacement actuator diaphragm

MCP-0202 3 to 12 psi actuator for MCP-1020 series

MCP-0203 5 to 10 psi actuator for MCP-1020 series

MCP-0205 8 to 13 psi actuator for MCP-1020 series

MCP-0206 10 to 15 psi actuator for MCP-1020 series

MCP-0208 4 to 8 psi actuator for MCP-1020 series

CAUTION

Pneumatic devices must be supplied with clean, dry

control air. Any other medium (e.g., oil or moisture

contamination) will cause the device to fail.

Summary of content (2 pages)

PAGE 1
MCP-1020/020X Series 2" Pneumatic Damper Actuators Description The KMC MCP-1020/020X Series 2" Pneumatic Damper Actuators are designed to position automatic air dampers in pneumatically controlled systems. They may be used for gradual or twoposition applications. Models are available with right-angle bracket mounting and several linkage options.
PAGE 2
Details All dimensions are in inches (mm) Damper Type Up to 1000 FPM 1000 to 2500 FPM 2500 to 3000 FPM Opposed blades without seals 3 in-lb / sq.-ft 4.5 in-lb / sq.-ft 6 in-lb / sq.-ft Parallel blades without seals 4 in-lb / sq.-ft 6 in-lb / sq.-ft 8 in-lb / sq.-ft Opposed blades with seals 5 in-lb / sq.-ft 7.5 in-lb / sq.-ft 10 in-lb / sq.-ft Parallel blades with seals 7 in-lb / sq.-ft 10.5 in-lb / sq.-ft 14 in-lb / sq.