Product Overview

ManualsBrandsKMC Controls ManualsDampersCombination Air Flow Transducer-Actuator, 2-10 VDC Input, 18°/Minute

Table Of Contents

Description and Application

Speciﬁcations and design subject to change without notice.

TSP-5000 Series

Air Flow Transducer-Actuators

◆ Direct mounting to 1/2" diameter or 3/8" square

damper shaft, or a 3/8" diameter shaft (requires

HFO-0011 shaft adaptor)

◆ 18°/ minute or 60°/minute actuator models

◆ Gear disengagement feature allows positioning

the damper and/or gear-train without unit

activation

◆ Twin platinum resistance temperature detectors

◆ Built-in 10,000 ohm, 1/3 wa feedback

potentiometer on the TSP-5003/5023 (only)

◆ Proportional or tri-state inputs

These combination air ow transducers and actuator

units are designed primarily for variable air volume

terminal units controlled via Direct Digital Control

(DDC) systems such as KMC’s Digital System.

They can be used in slave or dual duct tracking

applications.

Air ow is sensed by utilizing a single or multi-point

dierential (velocity) pressure measuring station or

pitot tube. Air ow sensing is accomplished utilizing

twin platinum resistance temperature detectors.

Velocity measurement is maintained at 3% accuracy

over the range of 0 to 3,300 feet per minute (FPM).

Each unit mounts directly to a 1/2" diameter or

3/8" square damper shaft, or a 3/8" diameter shaft

(HFO-0011 shaft adaptor required). Damper

control is provided by an 18°/minute or 60°/minute

actuator. The actuator is controlled by an SPDT

“oating” input (on the TSP-5003/5023) or 2–10

VDC proportional input (on the TSP-5002/5022).

A minimum of 50 in-lbs. torque is provided. Both

minimum and maximum stops are standard to limit

the rotation. A gear disengagement feature allows

positioning the damper and/or gear-train without

energizing the actuator.

A 10,000 ohm, 1/3 wa feedback potentiometer is

standard on the TSP-5003/5023 (only).

Features

Models

TSP-5002 2–10 VDC input, 18°/ minute

TSP-5022 2–10 VDC input, 60°/ minute

TSP-5003 Tri-state input, 18°/ minute

TSP-5023 Tri-state input, 60°/ minute

Accessories

Dierential Pressure Flow Sensors

SSS-1002 3-5/32 inches long (80 mm)

SSS-1003 5-13/32 inches long (137 mm)

SSS-1004 7-21/32 inches long (195 mm)

SSS-1005 9-29/32 inches long (252 mm)

Mounting and Connection Hardware

HFO-0011 3/8" shaft adaptor

HMO-1003 Replacement non-rotation

bracket (one included)

HMO-4520 Compression connector for

plenum cable

Summary of content (2 pages)

PAGE 1
TSP-5000 Series Air Flow Transducer-Actuators Description and Application These combination air flow transducers and actuator units are designed primarily for variable air volume terminal units controlled via Direct Digital Control (DDC) systems such as KMC’s Digital System. They can be used in slave or dual duct tracking applications. Air flow is sensed by utilizing a single or multi-point differential (velocity) pressure measuring station or pitot tube.
PAGE 2
Dimensions All dimensions are in inches TSP-5003/5023 TSP-5002/5022 Damper Type Up to 1000 FPM 1000 to 2500 FPM 2500 to 3000 FPM Opposed Blades Without Seals 3 in-lb. per square foot 4.5 in-lb. per square foot 6 in-lb. per square foot Parallel Blades Without Seals 4 in-lb. per square foot 6 in-lb. per square foot 8 in-lb. per square foot Opposed Blades With Seals 5 in-lb. per square foot 7.5 in-lb. per square foot 10 in-lb. per square foot Parallel Blades With Seals 7 in-lb.