Manual

ManualsBrandsKMC Controls ManualsSensorsTPE-1483 Series(2004-2008)

Description

The KMC TPE–1483 series of pressure transducers

incorporates a Wet / Wet differential pressure

transmitter featuring low hysteresis, excellent

repeatability, and long-term stability.

Up to four field-selectable input ranges are available

in most models. The field selectable feature

provides a single model that can be configured to

cover all the input pressure ranges for any given

application.

Three output ranges are field selectable, 4 to 20mA,

0 to 5 VDC, and 0 to 10 VDC. The output signal is

factory calibrated and temperature compensated

for the highest start-up accuracy.

The TPE–1483 can be powered from either a 24

VAC nominal or 12 to 30 VDC power source.

TPE–1483 incorporates a rugged NEMA 4

enclosure.

TPE–1483 Series

Pressure Transducer

Specifications and design subject to change without notice.

Models

The following models are available

TPE–1483–1 0 to 5/10/25/50 psig/d

TPE–1483–2 0 to 10/20/50/100 psig/d

TPE–1483–3 0 to 50/100/250/500 psig/d

Features

◆ Push-button and remote zeroing terminal

◆ Uni-directional or bi-directional pressure range

selection switch

◆ High / low port swap switch to solve incorrect

plumbing for differential

◆ Normal or slow surge damping switch to

prevent false alarms and reduce noise

◆ Output polarity reverse switch

Application

KMC TPE–1483 Pressure Transducers are suited for

any application requiring a reliable pressure

monitor providing a dependable conditioned and

compensated signal output.

The TPE–1483 may be used with any liquid or gas

that is compatible with 17–4 PH stainless steel.

DO NOT USE for these applications:

◆ Oxygen service

◆ Explosive/hazardous environments

◆ Flammable or combustible materials

Valid late 2004 into 2008—

see Rev. C of this data

sheet for information on the

new case and board.

Summary of content (6 pages)

PAGE 1
Valid late 2004 into 2008— see Rev. C of this data sheet for information on the new case and board. TPE–1483 Series Pressure Transducer Description The KMC TPE–1483 series of pressure transducers incorporates a Wet / Wet differential pressure transmitter featuring low hysteresis, excellent repeatability, and long-term stability. Up to four field-selectable input ranges are available in most models.
PAGE 2
Enclosure Specifications Media compatibility 17–4 PH stainless steel Supply Voltage 24 VAC or 15 to 30 VDC Supply Current 35 mA, maximum @ 24VDC Output Signal 4 to 20mA, 0 to 5 or 0 to 10 VDC, field selectable Pressure Ranges Field selectable: TPE–1483–1 0 to 5/10/25/50 psig/d TPE–1483–2 0 to 10/20/50/100 psig/d TPE–1483–3 0 to 50/100/250/500 psig/d Proof Pressure Max. 2X F.S. range Burst Pressure Max. 5X F.S. range Accuracy ±1% F.S. combined linearity, hysteresis, and repeatability.
PAGE 3
Valid late 2004 into 2008—see Rev. A of this installation guide for information on the new case and board. Wet-Wet Differential Pressure Transducer TPE-1483 Series Installation Guide Mounting Avoid locations with severe vibrations or excessive moisture. The enclosure has a standard ½" conduit opening and may be installed with either a conduit coupler or a cable gland type fitting. 1. Mount on a vertical surface with the pressure port and cable entrance on the bottom. 2.
PAGE 4
Wiring Use 22 AWG shielded wiring for all connections. Do not locate device wires in the same conduit as wiring supplying inductive loads. 1. Connect the positive DC voltage or the hot side of the AC voltage to the terminal marked PWR. 2. Connect the power supply common to the terminal marked COM. The device is reverse voltage protected and will not operate if connected backwards. The analog output signal is available on the OUT terminal.
PAGE 5
Set-Up Continued JUMPER SETTINGS Refer to the detailed drawing for pin location, the letter designations do not appear on the actual board.
PAGE 6
Set-Up Continued. OPERATION For normal operation such as 0 to 100 PSI, the pressure applied to the High port must be higher than the pressure applied to the Low port. If the pressure connection is reversed then the transmitter will always output 4 mA or 0 V. If the Low port is left open to ambient pressure, then the High port is used to measure a positive pressure and 0 PSI = 4 mA and 100 PSI = 20 mA.