Owner's manual

ManualsBrandsKMC Controls ManualsSensorsSAE-1152(NEW Style Board)

SAE-1101/1102/1151/1152 Carbon Monoxide (CO) Detectors 1 Installation Guide

Installation Guide

Carbon Monoxide (CO) Detectors

SAE-1101/1102/1151/1152

SAE-1101/1102 Space Mount

Install the unit at least ve feet above the nished oor

of the area to be controlled. Do not install near doors,

windows, supply air diffusers of other known air

disturbances. Avoid areas prone to vibration or rapid

temperature change.

1. Remove the cover by loosening and removing the

four screws.

2. Remove a knockout from the top or boom for

wiring.

3. Aach the universal backplate directly to a

standard electrical box using two screws.

4. Aer wiring, conguring, and testing the unit,

reinstall the cover.

SAE-1151/1152 Duct Mount

Choose a mounting location in a straight section of

a return air duct. Mount at least 5 feet (or 7.5 duct

diameters) from corners and other items that may

cause disturbances in the air ow. Avoid areas prone

to vibration or rapid temperature change.

1. Cut a 1

⁄8-inch hole in the duct for the air sampling

tube.

2. Remove the cover by loosening and removing the

four screws.

3. Remove a knockout from the top or boom for

wiring.

4 . Insert the sampling tube into the duct. Use the

foam plug (included) to prevent air from entering

the enclosure, causing false readings.

5. Centering the sensor over the hole in the

ductwork, aach the unit to the ductwork by

threading four screws through the self-sealing

rubber gaskets on the backplate of the housing.

6. Aer wiring, conguring, and testing the unit,

reinstall the cover.

Mounting

Accessories

IEI-1001 LCD Display Module

(required for congu-

ration)

XEE-6111-040 Transformer, 120-

to-24 VAC, 40 VA,

single-hub

XEE-6112-040 Transformer, 120-to-

24 VAC, 40 VA, dual-

hub

4.9" W (124 mm)

7.22" H

(183 mm)

1.69" D (43 mm)

9.9" D (250 mm)

with duct

insertion tube

Models

SAE-1101 Space CO sensor (aer 5/2007)

SAE-1102 Space CO sensor with two relays

and audible alarm (aer 2/2007)

SAE-1151 Duct CO sensor (aer 12/2006)

SAE-1152 Duct CO sensor with two relays

and audible alarm (aer 11/2004)

NOTE: These instructions apply to units

manufactured aer the corresponding

dates shown in the Models list. For older

units (with a row of LEDs on the le side

of the board), see the original version of

this installation guide available on www.

kmccontrols.com.

Summary of content (5 pages)

PAGE 1
Carbon Monoxide (CO) Detectors SAE-1101/1102/1151/1152 Mounting Installation Guide SAE-1101/1102 Space Mount Install the unit at least five feet above the finished floor of the area to be controlled. Do not install near doors, windows, supply air diffusers of other known air disturbances. Avoid areas prone to vibration or rapid temperature change. 1. Remove the cover by loosening and removing the four screws. 2. Remove a knockout from the top or bottom for wiring. 3.
PAGE 2
Wiring NOTE: These instructions apply to units manufactured after the corresponding dates shown in the Models list. For older units (with a row of LEDs on the left side of the board), see the original version of this installation guide available on www. kmccontrols.com. Use 22 AWG shielded wiring for all connections. Do not locate device wires in the same conduit with wiring used to supply inductive loads. 1.
PAGE 3
Set-Up Warm-Up Menu Configuration/Testing/Calibration 1. Verify that the detector is properly wired and all connections are tight. 2. Apply power. NOTE: These instructions apply to units manufactured after the corresponding dates shown in the Models list. For older units (with a row of LEDs on the left side of the board), see the original version of this installation guide available on www. kmccontrols.com.
PAGE 4
SAVE button. Press the MENU button. Returns to normal operation. Normal (Configuration) Menu Press and release the MENU button to enter the configuration menu: 1. BUZZER TRIP=150: The factory default for the buzzer trip level is 150 ppm. This can be changed by using the ROLL button from 100 to 400 ppm in increments of 10 ppm. Use the SAVE button to save any change to memory. Press the MENU button. Test Menu 1.
PAGE 5
Calibration Specifications Range Output Calibration 0–300 ppm If necessary, the current and voltage outputs can be calibrated as described previously in the Menu Configuration section by using the buttons and a meter connected to the output. See the Set-Up section.