Installation and Operation Guide NetSensor ® KMD-1261 and KMD-1281 Motion, temperature and humidity sensors Contents Specifications ............................................................... 2 Network cable preparation ........................................... 5 Rough-in preparation ................................................... 6 Installing the NetSensor ................................................ 7 Operation ....................................................................
KMC Controls Specifications Display LCD, 4-character, 7-segment, 0.375 in. high. (temperature) Compatibility KMD-5800 series controllers KMD-7000 series controllers BAC-5800 series BACnet controllers BAC-7000 series BACnet controllers Controller Connection Connector type Cable length PC port RJ–12 connects data and power to compatible controllers Maximum 75 feet (22.
NetSensor Installation and Operation Accessories Mounting backplate Almond 4 x 4 inch HMO-1161 White 4 x 4 inch HMO-1161W Gasket HPO-1161 Replacement Allen screws HPO-0044 (package of 10) Network plenum cables with connectors 25 feet (7.6 meters) 50 feet (15.2 meters) 75 feet (22.9 meters) KMD-5690 KMD-5691 KMD-5692 Sensor Accuracy, KMD-1261 Type Accuracy Resistance Operating range Thermistor ±0.36° F (±0.2° C) 10,000 at 77° F (25° C) 48° to 96° F (8.8° to 35.
KMC Controls Dimensions A B CD E F A B C D E F 3.25 in. 5.16 in. 2.58 in. 3.25 in. 0.87 in. 1.07 in.
NetSensor Installation and Operation Motion sensor range 10 m 32.8 ft 33 feet (10 meters) X 10 m 32.8 ft Y 46.5° 0° 0° 10 m 32.8 ft 55° 10 m 32.8 ft Side view Top view Network cable preparation Connecting a NetSensor to a controller requires a six-wire cable with RJ-12 connectors on each end. KMC plenum-rated preassembled cables are recommended. Cables made to length must meet the following requirements: ◆ Cable length must be no longer than 75 feet (22.9 meters).
KMC Controls Rough-in preparation Caution To prevent mounting screw heads from touching the circuit board in the NetSensor, use only the mounting screws supplied by KMC Controls. Using screws other than the type supplied will damage the NetSensor. Complete rough-in wiring at each sensor location prior to sensor installation. This includes the following. ◆ ◆ Routing the network cable from the NetSensor to a controller. If required, installing the appropriate backplate.
NetSensor Installation and Operation Installing the NetSensor 1. Turn the Allen screws in the base of the NetSensor clockwise until they clear the cover. Swing the sensor away from the mounting base to remove it. Turn clockwise to remove from base. Mounting screws 2. Route the RJ-12 cable through the mounting base. 3. Fasten the mounting base directly to a 2 x 4 inch outlet box or a backplate with the Allen screws toward the floor. 4. Insert the RJ-12 cable coming from the base into the NetSensor. 5.
KMC Controls Operation The following sections describe the controls and indicators found on the NetSensor. Display The temperature display contains four 0.375-inch, 7-segment LCD digits that are visible across a normal size office. The display provides time, temperature and on the KMD-1281 humidity readouts. Room temperature is displayed until either setpoint button is pressed and then the display changes to setpoint mode.
NetSensor Installation and Operation Programming instructions Programming instructions for NetSensors are included in Help supplied with WinControlXL, BACstage, and TotalControl. Maintenance Remove dust as necessary from holes in top and bottom. Clean the display and motion sensor cover with a soft, damp cloth and mild soap.
KMC Controls Important notices The KMC logo, WinControlXL and NetSensor are registered trademarks of KMC Controls, Inc. TotalControl and BACstage are trademarks of KMC Controls, Inc. ©2012, KMC Controls, Inc. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form by any means without the written permission of KMC Controls, Inc. Printed in U.S.A.
