Product Manual

ManualsBrandsKlutch ManualsMetal FabricationRatcheting Pipe Threader Set — 12-Pcs.

3/8in. to 2in. Ratcheting Pipe Threader Set

OWNER’S MANUAL

3/8in. to 2in. Ratcheting Pipe Threader Set

OWNER’S MANUAL

Operating Instructions

Caution: Make sure the pipe end and threads of the die are sufficiently oiled at all times.

Otherwise, die life will be shortened and the threads will be rough.

Once the proper die is installed, you are ready to attach the Ratchet Holder to the pipe, and

begin cutting threads.

1. Place the rear of the die over the end of the pipe to be threaded. Verify that the inside

diameter of the die matches the outside diameter of the pipe.

2. Make sure that the pipe to be threaded is properly held in place.

3. While applying pressure to the end of the pipe, begin rotating

the Handle around the pipe to engage the die to the pipe end.

Continue this operation until the desired thread length is

achieved.

4. To disengage the Ratchet Holder after threading is complete,

follow steps discussed in #7 above to reverse the direction, and

then rotate the Connecting Rod until the die is disengaged from

the pipe end.

5. When sliding the pipe out of the Ratchet Holder, be careful not to damage newly cut threads.

Maintenance

Maintain your tool. It is recommended that the general condition of any tool be examined before

it is used. Keep your tool in good repair by adopting a program of conscientious repair and

maintenance in accordance with the recommended procedures found in this manual. Keep all

cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control. Keep handles dry, clean, and free from oil and

grease.

1. Clean the Pipe Threading tool after each use. Clean dies after each use. Check for broken

teeth or pipe material between teeth.

2. When not in use, store all parts in the case, and store the case in a dry location.

Parts Diagram

Parts List

Replacement Parts

• For replacement parts and technical questions, please call Customer Service at

1-800-222-5381.

• Not all product components are available for replacement. The illustrations provided are a

convenient reference to the location and position of parts in the assembly sequence.

• When ordering parts, the following will be required: model number, serial number/lot date

code, and description.

• The distributor reserves the rights to make design changes and or improvements to product

lines and manuals without notice.

Limited Warranty

Northern Tool and Equipment Company, Inc. ("We'' or '"Us'') warrants to the original purchaser

only ("You'' or “Your”) that the Klutch product purchased will be free from material defects in

both materials and workmanship, normal wear and tear excepted, for a period of one year from

date of purchase. The foregoing warranty is valid only if the installation and use of the product

is strictly in accordance with product instructions. There are no other warranties, express or

implied, including the warranty of merchantability or fitness for a particular purpose. If the

product does not comply with this limited warranty, Your sole and exclusive remedy is that We

will, at our sole option and within a commercially reasonable time, either replace the product or

product component without charge to You or refund the purchase price (less shipping). This

limited warranty is not transferable.

Limitations on the Warranty

This limited warranty does not cover: (a) normal wear and tear; (b) damage through abuse,

neglect, misuse, or as a result of any accident or in any other manner; (c) damage from

misapplication, overloading, or improper installation; (d) improper maintenance and repair; and

(e) product alteration in any manner by anyone other than Us, with the sole exception of

alterations made pursuant to product instructions and in a workmanlike manner.

4 of 6 5 of 6

Part No.

D-1

D-2

D-3

D-4

D-5

D-6

D-7

Description

DIES THREADER 3/8"

DIES THREADER 1/2"

DIES THREADER 3/4"

DIES THREADER 1”

DIES THREADER 1-1/4

DIES THREADER 1-1/2

DIES THREADER 2”

OIL CAN

DIES FRAME

WORK HANDLE

SCREW

COVER

DIES

DIES HEAD

RATCHET COUPLING

SCREW

Q’ty

Part No.

Description

PLASTIC GLAND

RATCHET HOLDER

RATCHET

STEEL RETAINING RING

SCREW

PAWL

PRESS SPRING

TIGHTENING RING

RETAINING RING

SPRING BOLT

KNOB

CONNECTING ROD

ROD CONNECTER

CONNECTING ROD

PLASTIC HANDLE

Q’ty