Product Manual

52in. W Capacity 3-in-1 Combination
Sheet Metal Machine OWNER’S MANUAL
52in. W Capacity 3-in-1 Combination
Sheet Metal Machine OWNER’S MANUAL
Important Safety Information
WARNING:
• DO NOT allow persons to operate or assemble this product until they have read this manual
and have developed a thorough understanding of how the product works. Failure to follow all
instructions may result in serious injury.
• The warnings, cautions, and instructions in this manual cannot cover all possible conditions
or situations that could occur. Exercise common sense and caution when using this tool.
Always be aware of the environment and ensure that the tool is used in a safe and
responsible manner.
• DO NOT modify the product in any way. Unauthorized modification may impair the function
and/or safety and could affect the life of the product. There are specific applications for
which the product was designed.
• Use the right tool for the job. DO NOT attempt to force a small equipment to do the work of
larger industrial equipment. There are certain applications for which this equipment was
designed. It will do the job better and more safely at the capacity for which it was intended.
DO NOT use this equipment for a purpose for which it was not intended.
• Industrial or commercial applications must follow OSHA requirements.
WARNING:
• This product may contain chemicals known to the State of California to cause cancer, birth
defects or other reproductive harm.
WARNING:
• Inspect the work area before each use. Keep work area clean, dry, free of clutter, and well lit.
Cluttered, wet, or dark work areas can result in injury. Using the tool in confined work areas
may put you dangerously close to other cutting tools and rotating parts.
• Do not use the tool where there is a risk of causing a fire or an explosion; e.g., in the
presence of flammable liquids, gases, or dust. The tool can create sparks, which may ignite
the dust or fumes.
• Do not allow the tool to come into contact with an electrical source. Contact will cause a
shock.
• Keep children and bystanders away from the work area while operating the tool. Do not allow
children to handle the tool.
• Be aware of all power lines, electrical circuits, water pipes, and other mechanical hazards in
your work area. Some of these hazards may be below the work surface hidden from your
view and may cause personal harm or property damage if unintentionally contacted.
PERSONAL SAFETY
• Stay alert, watch what you are doing, and use common sense when operating the tool. Do
not use the tool while you are tired or under the influence of drugs, alcohol, or medication. A
moment of inattention while operating the tool may result in serious personal injury.
• Dress properly. Do not wear loose clothing, dangling objects, or jewelry. Keep your hair,
clothing and gloves away from moving parts. Loose clothes, jewelry, or long hair can be
caught.
• Wear the proper personal protective equipment when necessary. Use ANSI Z87.1 compliant
safety goggles (not safety glasses) with side shields, or when needed, a face shield. Use a
dust mask in dusty work conditions. Also use non-skid safety shoes, hardhat, gloves, dust
collection systems, and hearing protection when appropriate. This applies to all persons in
the work area.
• Do not overreach. Keep proper footing and balance at all times.
• Secure the work with clamps or a vise instead of your hand when practical. This safety
precaution allows for proper tool operation using both hands.
CAUTION
PRODUCT USE AND CARE
• Do not force the tool. Tools do a better and safer job when used in the manner for which they
are designed. Plan your work, and use the correct tool for the job.
• Check for damaged parts before each use. Carefully check that the tool will operate properly
and perform its intended function. Replace damaged or worn parts immediately. Never
operate the tool with a damaged part.
• Store the tool when it is not in use. Store it in a dry, secure place out of the reach of children.
Inspect the tool for good working condition prior to storage and before re-use.
• Use only accessories that are recommended by the manufacturer for use with your tool.
Accessories that may be suitable for one tool may create a risk of injury when used with
another tool. Never use an accessory that has a lower operating speed or operating pressure
than the tool itself.
• Keep guards in place and in working order. Never operate the product without the guards in
place.
• Do not leave the tool running unattended.
Specific Operation Warnings
WARNING:
• Cut hazard. Keep fingers clear of the area in front and rear of the shear blades.
• Pinch point hazard. Keep hands clear of roller.
• Do not exceed the maximum shear capacity of 20 gauge mild steel.
• Do not exceed the maximum bending capacity of 22 gauge mild steel.
Assembly
When unpacking the sheet metal machine, check that all items are present.
• The 52 inch combination sheet metal machine
• Allen keys (5mm and 12mm Allen wrenches
• This manual
If any pieces are missing, call the distributor at the number in the Replacement Parts section of
this manual.
When unpacking, you must remove the bolts that are used to mount the machine to the
crate.Save these bolts for use when securing the machine in its working location. The machine
must be secured in place in order to avoid any unintended movementduring operation.
The sheet metal machine is coated at the factory with a rust inhibitor. To ensureproper fit and
operation, remove the coating before first use. The coating is easily removed with a mildsolvent,
such as mineral spirits, and a soft cloth.
Note: The handle is shipped mounted to the right side of the machine. If you wish to move
thehandle to the left side of the machine, proceed with the following instruction.
1. Remove one of the handles (26).
2. Loosen the handle adjustment knob (62) and slide the handle arm (18) out.
3. Slide the handle arm onto the opposite side and tighten the adjustment knob.
4. re-attach the handle to the handle arm.
5. The handle arm can be positioned in the eccentric shaft (35) as desired for appropriate torque.
2 of 9 3 of 9