Datasheet

ManualsBrandsKleinwächter GmbH ManualsESDElectrostatic Voltage / Field Meter Kit, ESD

User manual EFM/CPS 022

Part number : 61-200-0220

ELECTROSTATIC FIELDMETER

Small hand-held Electro-Fieldmeter with digital display designed to measure

electrostatic voltage potentials (with pre-selected distance) according the fieldmill

influence principal.

Item part numbers :

o 61-200-0220 : Eletrofield meter (EU plug)

o 61-200-0221 : Charge plate option

o 61-200-0222 : Complete set : Electrofield meter+Charge plate (EU plug)

o 61-300-0220 : Eletrofield meter (UK plug)

o 61-300-0222 : Complete set : Electrofield meter+Charge plate (UK plug)

Summary of content (9 pages)

PAGE 1
User manual EFM/CPS 022 Part number : 61-200-0220 ELECTROSTATIC FIELDMETER Small hand-held Electro-Fieldmeter with digital display designed to measure electrostatic voltage potentials (with pre-selected distance) according the fieldmill influence principal.
PAGE 2
User manual EFM/CPS 022 Part number : 61-200-0220 Contents Technical data 3 Operation instruction 3-5 Supplied accessories 5 Optionnal accessories 5 Charge plate (Kit CPS022) 6 Operation instruction CPS 022 7-8 Maintenance 7 Warning notice 8 Calibration 8 Legend 9 2
PAGE 3
User manual EFM/CPS 022 Part number : 61-200-0220 Technical data Description The unit is housed into an EMV - plastic enclosure . The Influence Measuring Electrode is star shaped. In front to it in a small distance apart a rotating grounded modulation propeller-wheel with the them shape is located. The Influence Electrode is jacket by a ring electrode system used also as mechanical shield for the propeller wheel and the sensor - plate. The measurement display is located on top of the unit.
PAGE 4
User manual EFM/CPS 022 Part number : 61-200-0220 on hold distance off 1 x press shortly „function/on“ 1 x press shortly „function/on“ to activate or deactivate 1 x press and hold „function/on“ until „change cm“ appears 1 x press shortly „function/on“ to select the distance or switching in CPS - Mode wait for app. 2 sec to take over new function 2 x press shortly „function/on“ button Operating Press the „function/on“-key to switch on the unit.
PAGE 5
User manual EFM/CPS 022 Part number : 61-200-0220 With any equipment you will get 2 distance supports. The distance supports can be screwed into the front - plate at the modulator side, which will always provide the right measurement distance for the standard setting of „distance = 2 cm“ Display The alphanumeric Liquid Crystal Display (LCD) consists of 2 lines for 12 digits each.
PAGE 6
User manual EFM/CPS 022 Part number : 61-200-0220 With the Charge Plate Kit becomes from the EFM 022 a charge plate monitor , to the supervision of air ionization appliances after the EN 100015 as well as EOS/ESD S.3.1 The charge electrode corresponds to the norms from the capacity (20pF), but not from the dimensions. For directly measure conform to the norms, use our CPM 374. With the CPS 022, however reproducible measurements can be performed. It becomes the decay-time from + 1.000V…. + 100V or.- 1.000V.
PAGE 7
User manual EFM/CPS 022 Part number : 61-200-0220 The EFM 022 from software version V4.0 is prepared for using the Charge – Plate - Monitor.
PAGE 8
User manual EFM/CPS 022 Part number : 61-200-0220 Zero Adjust A zero adjustment is normally not needed. In case, that the unit does not indicate U=00X while the modulator system is shielded (e.g. grounded person covers the modulator system with one hand), use the trimmer (6) for zero adjustment. The last digit can be ignored as the caused measurement failure is much lower than the specified tolerance.
PAGE 9
User manual EFM/CPS 022 Part number : 61-200-0220 Legend 1. 2. 3. 4. 5. 6. 7. Modulatorsystem LCD – Display (2 x 12) alphanumeric Function Key Grounding Socket Battery Compartment Zero Adjustment Trimmer Protection Cup. remove for measuring !! 8.