Operation Manual

ManualsBrandsKlarstein ManualsHouseholdIC-F62D NXDN

Table Of Contents

iF52D

13 OPTIONS

12 OTHERS

11 Bluetooth

OPERATION

10 VOICE RECORDER FUNCTIONS

9 BIIS 1200 SYSTEM OPERATION

8 MDC 1200 SYSTEM OPERATION

7 NXDN™ OPERATION

6 MENU SCREEN

5 SCAN OPERATION

4 ADVANCED OPERATION

3 BASIC OPERATION

2 PANEL DESCRIPTION

1 ACCESSORIES

INTRODUCTION

VHF DIGITAL TRANSCEIVER

OPERATING GUIDE

iF62D

UHF DIGITAL TRANSCEIVER

Summary of content (125 pages)

PAGE 1
OPERATING GUIDE INTRODUCTION VHF DIGITAL TRANSCEIVER iF52D UHF DIGITAL TRANSCEIVER iF62D 1 ACCESSORIES 2 PANEL DESCRIPTION 3 BASIC OPERATION 4 ADVANCED OPERATION 5 SCAN OPERATION 6 MENU SCREEN 7 NXDN™ OPERATION 8 MDC 1200 SYSTEM OPERATION 9 BIIS 1200 SYSTEM OPERATION 10 VOICE RECORDER FUNCTIONS 11 Bluetooth® OPERATION 12 OTHERS 13 OPTIONS
PAGE 2
INTRODUCTION Thank you for choosing this Icom product. This product is designed and built with Icom’s state of the art technology and craftsmanship. With proper care, this product should provide you with years of trouble-free operation. IMPORTANT FIRST, CAREFULLY READ PRECAUTIONS AND INSTRUCTIONS that are provided with the transceiver. SAVE THIS OPERATING GUIDE— This operating guide contains additional important operating instructions for the following transceivers. Icom, Icom Inc.
PAGE 3
Section 1 ACCESSORIES Supplied accessories ��1-2 Attaching accessories ��1-3 DDFlexible antenna ��1-3 DDBattery pack ��1-3 DDBelt clip ��
PAGE 4
1 ACCESSORIES Supplied accessories The following accessories are supplied. NOTE: Some accessories are not supplied, or the shape is different, depending on the transceiver version.
PAGE 5
1 ACCESSORIES Attaching accessories DDFlexible antenna Connect the required flexible antenna to the antenna connector. CAUTION: •• DO NOT carry the transceiver by holding only the antenna. •• DO NOT connect an antenna other than those listed in the INSTRUCTIONS. ••Transmitting without an antenna may damage the transceiver. DDBattery pack Battery sliding locks CAUTION: DO NOT attach or detach the battery pack when the transceiver is wet or soiled.
PAGE 6
1 ACCESSORIES Accessory attachments DDBelt clip To attach: 1. Remove the battery pack from the transceiver, if it is attached. 2. Slide the belt clip in the direction of the arrow until the belt clip is locked and makes a ‘click’ sound. Belt clip To detach: Lift the tab up (q), and slide the belt clip in the direction of the arrow (w). BE CAREFUL! DO NOT break your fingernail.
PAGE 7
1 ACCESSORIES Accessory attachments (Continued) DDConnector cover CAUTION: BE SURE to attach the connector cover when an optional device is not in use. Otherwise the terminals of the multi-connector may be shorted by a metal object, or become rusty by water intrusion. This could damage the transceiver. To attach: 1. Attach the connector cover over the multiconnector. (q) 2. Tighten the screw. (w) w q To detach: 1. Remove the screw. (z) 2.
PAGE 8
Section 2 PREPARATION Front, top and side panels ��2-2 DDAbout the Status indicator ��2-2 DDAbout the Multi-connector ��2-2 DDAbout the Software key functions ��2-2 Function display ��2-3 D
PAGE 9
2 PANEL DESCRIPTION Front, top and side panels DDAbout the Status indicator [VOL] •• Lights white, then blinks red, yellow, and green when turning ON the transceiver. ••Lights red while transmitting. •• Lights green while receiving a signal, or when the squelch is open. Status indicator DDAbout the Multi-connector [Rotary Encoder] Antenna Connector [Emer] [PTT] [OK] [F1] Multiconnector [P1 (Down)] [P2 (Up)] [Back] Connects to an optional speaker microphone or headset.
PAGE 10
2 PANEL DESCRIPTION Function display q w MESSAGE ICON • Blinks after messages (Message or Status Message) have been received� • Stops blinking when the screen is changed, or any key is pushed, but is displayed if unread messages are still in the Message memory� • Disappears when all messages in the Message memory have been read� Icon Area Individual-3 Call Scan NOTE: The screen is an example� The displayed position of each icon may differ, depending on the function being used� BELL ICON Displayed w
PAGE 11
2 PANEL DESCRIPTION Function display Icon Area Individual-3 Call Text Area Scan Key Display Area NOTE: The screen is an example. The displayed position of each icon may differ, depending on the function being used. Icons (Continued) MOTION SENSOR ICON Displayed when the Motion Sensor function is ON. NOISE CANCEL ICON Displayed when the Noise Cancel function is ON. SURVEILLANCE ICON Displayed when the Surveillance function is ON. VIBRATION ICON Displayed when the Vibration function is ON.
PAGE 12
2 PANEL DESCRIPTION Status indicator The Status indicator indicates the status of various parameters of the transceiver, as described below. (Reference: R=Red, ‌ G=Green, Y=Yellow, M=Magenta, W=White, B=Blue) • Programming: Blinks while reading or writing data. G • Programming Error: Blinks if cloning fails. R G R G R G R G R G R G R G R G • Channel Error: Blinks when you select a blank channel, or an unlocked channel.
PAGE 13
2 PANEL DESCRIPTION Status indicator (Continued) • Audible: Blinks while in the Audible mode. Y • Power ON: Lights white, then blinks red, yellow, and green at transceiver startup. Y W W W W W W W W • Success: Blinks slowly when your call was successful. R Y G R Y G G Y R G Y R Y Y Y Y G G G G • Failure: Blinks slowly when your call failed, or it was refused. Y Y Y Y R R R R • TX Error: Blinks when transmission is inhibited (Lockout, TX Inh, or TOT Penalty timer).
PAGE 14
2 PANEL DESCRIPTION Assignable Software key functions Digital (NXDN) Category – Assignable function 5-Tone LTR MDC BIIS ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ Null (p. 2-9) ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ Menu (p. 2-9) ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ Home (p. 2-9) ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ Shift (p.
PAGE 15
2 PANEL DESCRIPTION Assignable Software key functions (Continued) Digital (NXDN) Category Signaling / Call Trunking Assignable function GPS 2-Tone 5-Tone LTR MDC BIIS ✓ ✓ ✓ N/A N/A ✓ ✓ N/A Status (p. 2-12) ✓ ✓ ✓ N/A N/A ✓ ✓ ✓ Message (p. 2-12) ✓ ✓ ✓ N/A N/A ✓ ✓ ✓ Write Message (p. 2-12) ✓ ✓ ✓ N/A N/A N/A N/A ✓ Site Select (p. 2-12) N/A N/A ✓ N/A N/A N/A N/A N/A Site Lock (p.
PAGE 16
2 PANEL DESCRIPTION Assignable Software key functions (Continued) Disable Set to disable the key. Category: Channel/Scan CH Up, CH Down zzPush to select an operating channel. zz After pushing specific keys, push to select an option, setting, and so on. NOTE: This key function is assignable to only [Ext. Emer]. Null No function. Priority A, Priority B Push to select the Priority A or Priority B channel. Menu Push to display the “Menu” screen.
PAGE 17
2 PANEL DESCRIPTION Assignable Software key functions (Continued) Category: Channel/Scan (Voting) (Continued) Scan Add/Del (Tag) zz Push to add a channel to, or delete it from the current Scan list. Monitor zz Push to turn the CTCSS (DTCS), 2-Tone, or 5-Tone squelch mute ON or OFF. •• When a channel is added to the current Scan list, the current Scan list text and “ON” are briefly displayed.
PAGE 18
2 PANEL DESCRIPTION Assignable Software key functions (Continued) Category: Signaling/Call Call Emergency 1. Hold down during the Emer SW ON Timer period to enter the Emergency mode. 2. After the Reminder Timer period has passed, an Emergency call is automatically transmitted once, or repeatedly. In the Analog mode Push to make a call to the preset destination in the channel. NOTE: ••Set the related settings using the programming software. ••This key function is assignable to only [Emer] or [Ext.
PAGE 19
2 PANEL DESCRIPTION Assignable Software key functions (Continued) Category: Signaling/Call (Continued) Status 1. Push to display the “Status List” screen. 2. Push [Up] or [Down] to select a Status message. 3. Push [PTT] to send the message to the currently selected station or group, or push [OK] to set. Category: Functions Light Push to turn ON the backlight for about 5 seconds, even if the backlight setting is OFF. Message 1. While in the Standby mode, push to display the “Message List” screen.
PAGE 20
2 PANEL DESCRIPTION Assignable Software key functions (Continued) Category: Bluetooth Bluetooth Push to turn the Bluetooth® function ON or OFF. Category: Functions (Continued) AquaQuake™ While holding down this key, the AquaQuake water draining function removes water from the speaker grill by vibrating the internal speaker. Waiting Pairing Push to enter the Pairing Request Wait mode. LL Water in the speaker grill may muffle the sound coming from the speaker.
PAGE 21
Section 3 BASIC OPERATION Turning ON the transceiver ��3-2 DDTurning ON the transceiver ��3-2 DDAdjusting the audio level ��3-2 DDEntering the password ��3-2 Selecting a Zone ��
PAGE 22
3 BASIC OPERATION Turning ON the transceiver DDTurning ON the transceiver NOTE: Before using the transceiver for the first time, the battery pack must be fully charged for optimum life and operation. See the INSTRUCTIONS for details. [Rotary Encoder] [VOL] Rotate [VOL] to turn ON the transceiver. • The battery voltage or the opening text may be displayed, depending on the presetting. DDAdjusting the audio level [OK] When receiving a call, rotate [VOL] to adjust the audio output level.
PAGE 23
3 BASIC OPERATION Selecting a Zone DDSelecting a Zone
(Menu > Channel/Scan > Zone Select) Select a Zone type as shown: Conventional, Multi-site Conventional, LTR, Single-site Trunking, Multi-site Trunking, or Voting 1. Push [Menu] to display the Menu screen. 2. Push [P2 (Up)] or [P1 (Down)] to select “Channel/ Scan,” then push [OK]. TIP: What is a “Zone”? Certain channels are grouped together and assigned to a Zone according to their intended use.
PAGE 24
3 BASIC OPERATION Selecting a channel DDSelecting an operating channel DDSelecting the Priority A or B channel zzRotate [Rotary Encoder]. zzPush [CH Up] or [CH Down]. Push [Prio-A] or [Prio-B] to select the Priority A or Priority B channel. The transceiver automatically starts scanning when a Zone specified for the Voting operation is selected.
PAGE 25
3 BASIC OPERATION Selecting a channel (Continued) DDRewriting the Priority A or B channel DDSelecting a Continuous tone channel (Menu > Channel/Scan > Prio A (RW)) (Menu > Channel/Scan > Prio B (RW)) (Menu > Channel/Scan > C.Tone CH Sel) 1. W hile in the Analog mode, push [Menu] to display the “Menu” screen. 2. Push [P2 (Up)] or [P1 (Down)] to select “Channel/ Scan,” then push [OK]. 1. S elect a channel to be set as the Priority A or B channel. (p. 3-4) 2.
PAGE 26
3 BASIC OPERATION Selecting a channel (Continued) DDSelecting a RAN channel (Menu > Channel/Scan > RAN CH Select) 1. W hile in the Digital mode, push [Menu] to display the “Menu” screen. 2. Push [P2 (Up)] or [P1 (Down)] to select “Channel/ Scan,” then push [OK]. Menu Channel/Scan Signaling/Call ► ► 3. P ush [P2 (Up)] or [P1 (Down)] to select “RAN CH Sel,” then push [OK]. Channel/Scan RAN CH Sel RF Power ► ► 4. P ush [P2 (Up)] or [P1 (Down)] to select a RAN channel, then push [OK].
PAGE 27
3 BASIC OPERATION Call procedure When your system uses tone signaling (except CTCSS and DTCS), a call procedure may be necessary prior to voice transmission. The tone signaling employed may be a selective calling system, which enables you to call only specific stations, and prevents unwanted stations from contacting you. 1. S elect a channel according to your system operator’s instructions. LL This may not be necessary, depending on the presetting. LLSee page 3-4 for details. 2. P ush [Call]. 3.
PAGE 28
3 BASIC OPERATION Receiving and transmitting DDTransmitting notes CAUTION: DO NOT transmit without an antenna. It may damage the transceiver. See pages 1-3 for accessory attachments. Transmit inhibit function The transceiver has several inhibit functions which restrict transmission under the following conditions: • The channel is in the Inaudible mode (“ ”: Audible icon does not appear.) • The channel is busy.
PAGE 29
3 BASIC OPERATION Receiving and transmitting (Continued) DDSending a call to a destination When a tone frequency (2-Tone) or code (5-Tone) is preset in the Call List, a user can select it as a destination. (Menu > Signaling/Call > Call List Select) 1. Push [Menu] to display the Menu screen. 2. Push [P2 (Up)] or [P1 (Down)] to select “Signaling/ Call,” then push [OK]. Menu Channel/Scan Signaling/Call ► ► 3. P ush [P2 (Up)] or [P1 (Down)] to select “Call List Select,” then push [OK].
PAGE 30
3 BASIC OPERATION Key Lock function You can use the Key Lock function to prevent accidental channel changes and unnecessary function access. LL All assignable keys except the following are electronically locked: [Monitor], [Light], [Lock], [Call], [Emergency], and [Surveillance]. Also, [PTT] and [Power] are usable. Hold down [LOCK] for 1 second to turn the Key Lock function ON or OFF. Lock ON ••“Lock ON” is displayed when the Key Lock function is ON.
PAGE 31
Section 4 ADVANCED OPERATION DTMF calls ��4-2 DDAutodial ��4-2 DDStun function ��4-2 Emergency call ��4-3 DDTransmitting an Emergency call ��
PAGE 32
4 ADVANCED OPERATION DTMF calls DDAutodial DDStun function A user can quickly send DTMF tones that have been pre-entered into the transceiver. (Only for LTR operation) The Stun function is used when a transceiver is stolen or lost, and the function deactivates the transceiver. When the transceiver receives a matching Stun DTMF code, the Stun function is activated and the transceiver operation is inhibited.
PAGE 33
4 ADVANCED OPERATION Emergency call D Transmitting an Emergency call IMPORTANT: It is recommended that the dealer sets an Emergency channel in each Zone, to provide a reliable Emergency call operation� When the transceiver enters the Emergency mode, a countdown starts� The transceiver counts down during the Reminder Timer set time� Before the Reminder Timer set time expires, the transceiver transmits an Emergency call once, or repeatedly*, on the specifi ed Emergency channel.
PAGE 34
4 ADVANCED OPERATION Emergency call DD Transmitting an Emergency call (Continued) The transceiver enters the Emergency mode through the following functions: ••The Man Down function When the transceiver leans past the preset angle for the ON Timer preset time. Man Down With Stationary •• The transceiver leans past the preset angle for the ON Timer preset time. AND •• The transceiver is detected as stationary (no motion) for the ON Timer set time.
PAGE 35
4 ADVANCED OPERATION Emergency call D Transmitting an Emergency call (Continued) The transceiver enters the Emergency mode through the following functions: • The Lone Worker function When no operation occurs for the ON Timer preset time� Lone Worker With Stationary • When no operation occurs for the ON Timer preset time� AND • The transceiver is detected as stationary (no motion) for the ON Timer set time� L If a user pushes any key before the Reminder Timer set time expires, the Emergency mode is cance
PAGE 36
4 ADVANCED OPERATION Emergency call D Transmitting an Emergency call (Continued) The transceiver enters the Emergency mode through the following functions: • The Stationary Detection function When the transceiver is detected as being stationary (no motion) for the ON Timer preset time� • The Motion Detection function When the transceiver continuously moves for the ON Timer preset time� L If a user moves the transceiver during the Reminder Timer set time, the Emergency mode is canceled� L If a user hold
PAGE 37
4 ADVANCED OPERATION Scrambler Radio Access Number (RAN) The Voice Scrambler function provides private communication between stations. RAN is a signaling system designed for digital radio communications. When a channel is set up with a RAN, the squelch will open only when a call containing a matching RAN is received. If a call containing a different RAN is made on the same channel a user is using, a user will not hear the call. Push [Scrambler/Encryption] to toggle the Scrambler function ON or OFF.
PAGE 38
4 ADVANCED OPERATION AquaQuake™ Water Draining function By vibrating the speaker cone, the AquaQuake Water Draining function clears water from the speaker grill to maintain clear audio. 1. H old down [AquaQuake] to turn ON the AquaQuake water draining function. •• A low frequency vibration is generating to remove water from the speaker grill. •• Water in the speaker grill may muffle the sound coming from the speaker. 2. Release the key to turn OFF the function.
PAGE 39
Section 5 SCAN OPERATION Starting a Scan ��5-2 Canceling a Scan ��5-3 Selecting a Scan list ��5-4 Setting or clearing a Scan tag ��5-5 5-1 S C S S
PAGE 40
5 SCAN OPERATION Starting a Scan A Scan checks for signals on each channel and stops when a signal is received. NOTE: Two or more channels must be preset to start a Scan. (Menu > Channel/Scan > Scan ON/OFF) 1. Push [Menu] to display the Menu screen. 2. Push [P2 (Up)] or [P1 (Down)] to select “Channel/ Scan,” then push [OK]. Menu Channel/Scan Signaling/Call ► ► 3. P ush [P2 (Up)] or [P1 (Down)] to select “Scan ON/ OFF,” then push [OK]. Channel/Scan Scan List Scan ON/OFF ► ► 4.
PAGE 41
5 SCAN OPERATION Canceling a Scan (Menu > Channel/Scan > Scan ON/OFF) 1. Push [Menu] to display the Menu screen. 2. Push [P2 (Up)] or [P1 (Down)] to select “Channel/ Scan,” then push [OK]. Menu Channel/Scan Signaling/Call ► ► 3. P ush [P2 (Up)] or [P1 (Down)] to select “Scan ON/ OFF,” then push [OK]. Channel/Scan Scan List Scan ON/OFF ► ► 4. P ush [P2 (Up)] or [P1 (Down)] to select “OFF,” then push [OK]. Scan ON/OFF ✔ OFF ✔ ON SCAN ON/OFF OFF ••The Scan stops.
PAGE 42
5 SCAN OPERATION Selecting a Scan list You can select a Scan list to be scanned. Channels included in the selected Scan list are scanned during a scan. When selecting a Zone type Scan list, the channels that are in the same Zone as the Scan start channel will be scanned. (Menu > Channel/Scan > Scan List) 1. Push [Menu] to display the Menu screen. 2. Push [P2 (Up)] or [P1 (Down)] to select “Channel/ Scan,” then push [OK]. Menu Channel/Scan Signaling/Call ► ► 3.
PAGE 43
5 SCAN OPERATION Setting or clearing a Scan tag In a current Scan list: (Menu > Channel/Scan > Scan Tag) You can set or clear a Scan tag to or from a channel in a Scan list. The Scan tag channel is a target channel during a Scan. 1. S elect a channel. (p. 3-4) 2. Push [Menu] to display the Menu screen. 3. Push [P2 (Up)] or [P1 (Down)] to select “Channel/ Scan,” then push [OK]. In a current Scan list: 1. Select a channel. (p. 3-4) 2.
PAGE 44
Section 6 MENU SCREEN Menu screen description ��6-2 DDCategories ��6-2 DDUsing the Menu screen ��6-3 Menu items ��6-4 Channel/Scan ��
PAGE 45
6 MENU SCREEN Menu screen description The user can open the “Menu” screen using the [Menu] key. In the “Menu” screen, the setting items are categorized. Depending on the presetting, the user can select various functions and set the transceiver settings in the “Menu” screen. NOTE: The language displayed on the “Menu” screen is set to English by default, but a dealer can change it to another language using the programming software.
PAGE 46
6 MENU SCREEN Menu screen description DDUsing the Menu screen Example: Starting a Scan 1. Push [Menu] to display the Menu screen. 2. Push [P2 (Up)] or [P1 (Down)] to select “Channel/ Scan,” then push [OK]. Menu Channel/Scan Signaling/Call ► ► 3. P ush [P2 (Up)] or [P1 (Down)] to select “Scan ON/ OFF,” then push [OK]. Channel/Scan Scan List Scan ON/OFF ► ► 4. P ush [P2 (Up)] or [P1 (Down)] to select “ON,” then push [OK]. Scan ON/OFF ✔ OFF ✔ ON SCAN ON/OFF ON ••The Scan starts. 5.
PAGE 47
6 MENU SCREEN Menu items In the Menu screen, the items are categorized, as shown below. C.Tone CH Sel (C. Tone Channel Select) Sets the Continuous tone channel. Compander Turns the Compander function ON or OFF. Priority A CH (Priority A Channel) Selects the Priority A channel. Prio A (RW) (Priority A Rewrite) Sets a current channel as the Priority A channel. Priority B CH (Priority B Channel) Selects the Priority B channel. Prio B (RW) (Priority B Rewrite) Sets a current channel as the Priority B channel.
PAGE 48
6 MENU SCREEN Menu items Status Displays the “Status” screen. The preset Status messages are selectable. Signaling/Call Write Message Enables the user to directly enter a message. Roaming Reqst (Roaming Request) Turns the Roaming Request function ON or OFF. Trunking Site Lock Turns the Site Lock function ON or OFF. Site Select Selects a site. Lone Worker Turns the Lone Worker function ON or OFF. Surveillance Turns the Surveillance function ON or OFF. Functions VOX Turns the VOX function ON or OFF.
PAGE 49
6 MENU SCREEN Menu items Bluetooth Vibration Sensor Display Bluetooth Turns the Bluetooth function ON or OFF. Bluetooth Reset Initializes the Bluetooth unit. Auto Connect Select whether or not to automatically connect to a paired Bluetooth device when its power is turned ON. Audio Select Selects the AF Output device when a Bluetooth headset is connected. Bluetooth info (Bluetooth Information) Displays the installed Bluetooth unit name. Device List Displays the paired Bluetooth devices.
PAGE 50
6 MENU SCREEN Menu items Utility Information Sys Beep Lv (System Beep Level) Sets the System Beep output level. Emr Beep Lv (Emergency Beep Level) Sets the Beep output level when in the Emergency mode. Key Beep Lv (Key Beep Level) Sets the Key-touch Beep output level. Side Tone Lv (Side Tone Level) Set the Side Tone Beep output level. OP Beep Lv (Opening Beep Level) Sets the Opening Beep output level. Ringer Lv (Ringer Level) Sets the Ringer output level.
PAGE 51
6 MENU SCREEN Channel/Scan C.Tone CH Sel Scan List Sets a Scan list to be scanned. (p. 5-4) In the Analog mode Sets a Continuous tone channel. (p. 3-5) Scan ON/OFF Starts or cancels a Scan. A Scan checks for signals on each channel and stops when a signal is received. Compander Turns the Compander function ON or OFF. This function reduces noise components on the transmit audio for clear communication. Scram/Encrypt In the Analog mode Turns the Voice Scrambler function ON or OFF.
PAGE 52
6 MENU SCREEN Signaling/Call Call List Select Selects a calling destination. After selecting, push [PTT] to transmit the voice call to the selected destination. (pp. 3-9, 7-3, 7-4, 9-3) Incoming Displays a log of the received Individual call, Call Alert call, Status message, and Message. (pp. 7-17, 8-10, 9-9) Call Menu INDIV Select Displays the “Individual Select” screen. Then, push [P2 (Up)] or [P1 (Down)] to select a Individual ID from the Call List.
PAGE 53
6 MENU SCREEN Trunking Functions Roaming Request (For the Multi-site Trunk operation) Lone Worker Turns the Lone Worker function ON or OFF. When this function is ON, the transceiver automatically enters the Emergency mode if no operation occurs during the preset period. In the Digital mode Turns the Roaming Request function ON or OFF. When this function is turned ON, the transceiver starts a Roaming Scan, regardless of the error rate. (p.
PAGE 54
6 MENU SCREEN GPS Voice Rec (Voice Recording) My Position Displays the transceiver’s current location. Call Recorder Starts or stops the audio recording. LLOnly when the optional HM-233GP is connected to the transceiver. ••“ ” is displayed when the Call Record function is ON. LL Informatio •• While holding down [PTT], “ ” blinks, and the communication audio is recorded. •• Once the recording has started, the recording will continue, even if the transceiver is restarted.
PAGE 55
6 MENU SCREEN Audio Setting AF Max Level Sets the maximum audio output level. This function determines the maximum audio output level to inhibit the level from going higher than the set level. ••Range: 0 ~ 100 RX EQ Effect Selects the RX Equalizer Effect.
PAGE 56
6 MENU SCREEN Bluetooth Bluetooth Turns the Bluetooth function ON or OFF. ••OFF: Turns OFF the function. ••ON: Turns ON the function. PWR Sv (VS3) Selects whether to operate in the Bluetooth headset’s Battery Saving mode when the optional VS-3 Bluetooth® headset is connected. When the Power Save is activated, the user cannot use the VOX function. Bluetooth Reset Initializes the Bluetooth unit. Initialization can be done only when the Bluetooth function is OFF.
PAGE 57
6 MENU SCREEN Vibration Sensor OP Vibration Selects whether or not to vibrate the transceiver when it is turned ON. Man Dwn Ang Sets the Emergency mode detection angle for the Man Down function. If the transceiver leans past the set angle for the ON Timer time period, the transceiver enters the Emergency mode, and then a countdown starts. ••Options: 45, 60, or 75 degrees LLTo use this function, the Vibration function must be turned ON, in advance. ••OFF: Turns OFF the vibration.
PAGE 58
6 MENU SCREEN Display Backlight Sets the Key Backlight status. ••OFF: Turns the display backlight OFF. ••Auto: When any key except [PTT] is pushed, the backlight lights for 5 seconds. ••ON: Turns the backlight continuously ON. Contrast Sets the LCD contrast level. •• Range: 0 (the lowest) ~ 50 (the highest) LCD Test Checks whether or not the LCD displays correctly.
PAGE 59
6 MENU SCREEN Utility Sys Beep Lv Sets the System Beep output level. The beep sounds when connecting to or is locked out of the System. When a Linked option is selected, the beep level is adjustable with [VOL]. ••Range: 1 ~ 5, 1 (Linked) ~ 5 (Linked), or OFF Warning Beep Lv Sets the Warning Beep output level. The Warning Beep sounds when: ••the battery is exhausted. ••the Encryption key fails. When a Linked option is selected, the beep level is adjustable with [VOL].
PAGE 60
6 MENU SCREEN Information Battery Info Displays the battery voltage (Voltage), the remaining charge (Charge), the number of times charged (Cycle Count), the battery health (Health), and the battery model (Model). Comment Displays the transceiver’s comment. Comment 1 is displayed on the upper line, and the Comment 2 is on the lower line. Firmware Info Displays the transceiver’s firmware information. When an optional unit is installed, you can also check the unit information.
PAGE 61
Section 7 NXDN™ OPERATION NXDN™ system operation ��7-2 Transmitting a call ��7-3 DDTransmitting an Individual call ��7-3 DDTransmitting a Group call ��7-4 DDTransmitting a Status message ��7-5 DD
PAGE 62
7 NXDN™ OPERATION NXDN™ system operation NXDN has a new “Common Air Interface” (CAI), the name for over-the-air methods by which transceivers and repeaters communicate. NXDN defines the nextgeneration digital transceiver. The NXDN system has two operating modes, Conventional and Trunking. In a Conventional system, you manually search for an empty channel.
PAGE 63
7 NXDN™ OPERATION Transmitting a call NXDN operation enables you to make a call to a specific station (Individual call) or to a particular group (Group call). Other digital mode transceivers on the channel will not receive a call that does not match their Individual or Group ID and/or Radio Access Number (RAN) code. NOTE: When the handshake (repeater access) fails within the specified time period after pushing [PTT], the transceiver starts roaming.
PAGE 64
7 NXDN™ OPERATION Transmitting a call DDTransmitting a Group call You can call a specific group. TIP: ••You can also select a Group in the “Group Select” screen. (Menu > Signaling/Call > Group Select) ••You can also transmit a Group call through the Call Menu. (Menu > Signaling/Call > Call menu) •• When a Group ID is set in the Memory CH, you can transmit the Group call by pushing [PTT] on the channel. ••Push [Call List Select] to directly display the “Call List Select” screen in step 4 to the left.
PAGE 65
7 NXDN™ OPERATION Transmitting a call DDTransmitting a Status message You can transmit a preset simple message. You cannot transmit a voice signal at the same time. NOTE: If the following settings are configured using the CS-F52D programming software, the Status message can be automatically transmitted when: ••The transceiver is turned ON or OFF (Menu > Signaling/Call > Call Menu) LL Set the Status message to be transmitted in Power ON Status or Power OFF Status, respectively.
PAGE 66
7 NXDN™ OPERATION Transmitting a call DDTransmitting a Message You can transmit a message of up to 100 characters. TIP: ••You can also transmit a Status message through Message. (Menu > Signaling/Call > Message) ••Push [Message] to directly display the “Message” screen in step 6 to the left. ••Hold down [Message] for 1 second to transmit the preset Status message that is set in the “Message” screen. (Menu > Signaling/Call > Call Menu) 1. Push [Menu] to display the Menu screen. 2.
PAGE 67
7 NXDN™ OPERATION Transmitting a call DDDirectly entering message You can directly enter a message, then send it to the target station or group. TIP: •• The entered message can be temporary saved. After entering a Message in step 5, push [OK] to display “Save Msg?.” Push [P2 (Up)] or [P1 (Down)] to select “Yes,” then push [OK] to save. However, once the transceiver is turned OFF, the saved message is deleted. (Menu > Signaling/Call > Write Message) 1. Push [Menu] to display the Menu screen. 2.
PAGE 68
7 NXDN™ OPERATION Transmitting a call DDTransmitting a Call Alert call DDTransmitting a Remote Monitor call A Call Alert call enables you to notify another user who may be away from the transceiver that you want to talk. Remote Monitor call enables you to send a signal that requires the target station to transmit its microphone audio. (Menu > Signaling/Call > Call Menu) (Menu > Signaling/Call > Call Menu) 1. Push [Menu] to display the Menu screen. 2.
PAGE 69
7 NXDN™ OPERATION Transmitting a call DDTransmitting a Radio Check DDTransmitting a Stun command Radio Check call enables you to determine whether the target station is turned ON, within the communication range and on the channel, without requiring any action from the target station user. A Stun command enables you to send a signal that will stun the target station.
PAGE 70
7 NXDN™ OPERATION Transmitting a call DDTransmitting a Revive command DDTransmitting a Kill command A Revive command enables you to send a signal that will revive a stunned station. A Kill command enables you to send a signal that will disable the target station. If a Kill command is received, the target station cannot operate the transceiver until it is reprogrammed. (Menu > Signaling/Call > Call Menu) (Menu > Signaling/Call > Call Menu) 1. Push [Menu] to display the Menu screen. 2.
PAGE 71
7 NXDN™ OPERATION Transmitting a call DDTransmitting an Emergency call DDTransmitting Position data An NXDN Emergency call can be transmitted in the same way as the 2-Tone, 5-Tone, or MDC 1200 signaling operation. See “Emergency call” for details. (pp. 4-3 ~ 4-6) When the GPS function is ON, and the optional HM-233GP gps speaker microphone receives Position data, the longitude and latitude data can be automatically transmitted: ••When a GPS request status message is received.
PAGE 72
7 NXDN™ OPERATION Receiving a call DDReceiving an Individual call DDReceiving a Message When an Individual call is received: ••Mute is released. ••The Status indicator lights green. •• The calling station name (or ID) is displayed while receiving the signal. When a Message is received: ••Beeps sound. •• The Message and the calling station or Group name (or ID) are alternately displayed. ••“ ” blinks.* •• “ ” may be displayed or blink, depending on the presetting.
PAGE 73
7 NXDN™ OPERATION Receiving a call DDReceiving a Stun, Kill or Revive DDReceiving an Emergency call If a Stun or Kill command is received, the transceiver will display “Deactivated” and you cannot receive or transmit.* When an Emergency call is received: ••Beeps sound. •• “RX Emergency” and the calling station name (or ID) are alternately displayed. ••“ ” blinks.
PAGE 74
7 NXDN™ OPERATION Roaming function (For Multi-site Trunking operation) DDRoaming Request function The Multi-site Trunking mode enables the transceiver to move to another site, according to the preset Site list*, in order to find a site that has a higher quality signal, or provides better services. The Roaming function is automatically activated when the transceiver goes out of the range, and does not receive the downlink signal from the repeater in the currently registered site.
PAGE 75
7 NXDN™ OPERATION Site Lock function (For Multi-site Trunking operation) You can lock the transceiver to the currently registered Site. When this function is ON, the transceiver cancels resuming a Roaming scan, and stays on the current Site, regardless of the error rate. Hold down [Site Lock] for 1 second to turn the Site Lock function ON or OFF. ••“ ” is displayed when this function is turned ON.
PAGE 76
7 NXDN™ OPERATION Site Select function (For Multi-site Trunking operation) You can manually select a site without a Roaming scan. 1. P ush [Site Select] to display the “Site Select” screen. Site Select ✔1 ✔2 2. P ush [P2 (Up)] or [P1 (Down)] to select a Site from the preset Site list*, then push [OK]. * Up to 48 valid Roaming areas are listed. Site Select ✔1 ✔2 Site Select 2 •• The transceiver tries to register to the selected site.
PAGE 77
7 NXDN™ OPERATION Incoming list The transceiver saves a log of the received Individual calls, Call Alert calls, Status Messages, and Messages in the memory, depending on the presetting. Up to 10 Status/Message or 5 Voice/Call Alert calls can be saved in the log, and the oldest call record is deleted when an 11th (Status/Message) or 6th (Voice/Call Alert) call is received. However, once the transceiver is turned OFF, the all records are deleted.
PAGE 78
7 NXDN™ OPERATION Incoming list DDDeleting the Incoming list The receive call log can be deleted from the Incoming list. (Menu > Signaling/Call > Clear Incoming) 1. Push [Menu] to display the Menu screen. 2. Push [P2 (Up)] or [P1 (Down)] to select “Signaling/ Call,” then push [OK]. Menu Channel/Scan Signaling/Call ► ► 3. P ush [P2 (Up)] or [P1 (Down)] to select “Clear Incoming,” then push [OK]. Signaling/Call Call Menu Clear Incoming ► ► 4.
PAGE 79
7 NXDN™ OPERATION Outgoing list The transceiver saves a log of the transmitted Individual calls and Call Alert calls in the memory, depending on the presetting. Up to 5 calls can be saved in the log, and the oldest call record is deleted when a 6th call is received. However, once the transceiver is turned OFF, the all records are deleted. DDDisplaying the Outgoing list DDDeleting the Outgoing list (Menu > Signaling/Call > Outgoing) The transmit call log can be deleted from the Outgoing list. 1.
PAGE 80
7 NXDN™ OPERATION Encryption function The Encryption function enables voice scrambling, which provides private digital communication between stations. When an encrypted call is received, the squelch will open only when the call contains a matching Key ID*. If a call containing a different Key ID* is made on the same channel, the squelch will not open, and the user will not hear the call. * Depending on the presetting, opening the squelch may also require that a matching RAN is included in the call.
PAGE 81
7 NXDN™ OPERATION Over The Air Programming (OTAP) function The Over The Air Programming (OTAP) function enables wireless programming using a transceiver. NOTE: When using the OTAP function, the following settings are required in the optional CS-F52D programming software. Up until now, you needed programming software, a PC, and a data cable to program transceivers. As the number of transceivers in a system increased, the programming cost was higher and it took more time to program.
PAGE 82
Section 8 MDC 1200 SYSTEM OPERATION MDC 1200 system operation ��8-2 Transmitting a call ��8-3 DDTransmitting a PTT ID call ��8-3 DDTransmitting an MDC Emergency call ��8-3 DD Transmitting an MDC Emergency Acknowledgment ��8-3 DD Transmitting an
PAGE 83
8 MDC 1200 SYSTEM OPERATION MDC 1200 system operation This function is usable in only the Analog mode. The MDC 1200 signaling system enhances your transceiver’s capabilities. You can receive or transmit PTT ID, Emergency, Selective Call (SelCall), Call Alert, Radio Check, Stun, Revive, Status, and Message calls. Set one of the assignable software key functions for the MDC 1200 system operations. (pp.
PAGE 84
8 MDC 1200 SYSTEM OPERATION Transmitting a call DDTransmitting a PTT ID call You can transmit a call with your station ID. When another station receives a PTT ID call, your station ID is displayed. Push [PTT] to make a call. ••Beeps sound, depending on the presetting. •• Your station ID is transmitted when you push [PTT] (at the beginning of the transmission) or release [PTT] (at the end of transmission), depending on the presetting.
PAGE 85
8 MDC 1200 SYSTEM OPERATION Transmitting a call DD Transmitting an MDC Selective Call (Sel Call) DDTransmitting an MDC Call Alert call An MDC Sel Call enables you to make a call to a specific station, or to a particular group. Other MDC 1200 system transceivers on the channel do not receive a Sel Call that does not include the matching station or group ID. An MDC Call Alert call enables you to notify another user who may be away from the transceiver that you want to talk.
PAGE 86
8 MDC 1200 SYSTEM OPERATION Transmitting a call DDTransmitting an MDC Radio Check call DDTransmitting an MDC Stun call An MDC Radio Check call enables the user to determine whether the targeted station is turned ON, within the communication range and on the channel, without requiring any action from the targeted station user. An MDC Stun call remotely disables the transceiver. (Menu > Signaling/Call > Call Menu) 1. Push [Menu] to display the Menu screen. 2.
PAGE 87
8 MDC 1200 SYSTEM OPERATION Transmitting a call DDTransmitting an MDC Revive call DDTransmitting an MDC Status call An MDC Revive call revives a stunned transceiver to normal operation. An MDC Status call enables you to send a preset Status message. There are 16 kinds of Status messages. In addition, the transceiver can send an MDC Status Poll call that make the targeted station to automatically transmit a Status call, depending on the presetting. (Menu > Signaling/Call > Call Menu) 1.
PAGE 88
8 MDC 1200 SYSTEM OPERATION Transmitting a call DDTransmitting an MDC Message call You can send a MDC Message call. There are 16 kinds of Messages. (Menu > Signaling/Call > Message) 1. Push [Menu] to display the Menu screen. 2. Push [P2 (Up)] or [P1 (Down)] to select “Signaling/ Call,” then push [OK]. Menu Channel/Scan Signaling/Call ► ► 3. P ush [P2 (Up)] or [P1 (Down)] to select “Message,” then push [OK]. Signaling/Call INDIV Select Message ► ► 4.
PAGE 89
8 MDC 1200 SYSTEM OPERATION Receiving a call DDReceiving a PTT ID call DD Receiving an MDC Selective Call (Sel Call) When a PTT ID call is received: ••Beeps sound, depending on the presetting. ••May vibrate, depending on the presetting. ••The calling stationʼs ID is displayed. When an MDC Sel Call is received: ••Beeps sound. ••“ ” is displayed. ••“ ID 1 ” blinks. ••The calling stationʼs ID is displayed.
PAGE 90
8 MDC 1200 SYSTEM OPERATION Receiving a call DD Receiving an MDC Stun, Kill, or Revive call DDReceiving an MDC Message call When an MDC Message call is received. ••Beeps sound. •• The calling stationʼs ID and the Message are alternately displayed. If an MDC Stun or Kill call is received that matches your station ID, the transceiver displays “Deactivated” and you can not receive* or transmit.
PAGE 91
8 MDC 1200 SYSTEM OPERATION Incoming Call log function After receiving an MDC Sel Call, Call Alert call, or Emergency call, the call log may be displayed, depending on the presetting. Up to 5 calls can be memorized, and the oldest call is deleted when a 6th call is received. DDChecking the Incoming call log (Menu > Signaling/Call > Incoming) 1. Push [Menu] to display the Menu screen. 2. Push [P2 (Up)] or [P1 (Down)] to select “Signaling/ Call,” then push [OK].
PAGE 92
Section 9 BIIS 1200 SYSTEM OPERATION BIIS 1200 system operation ��9-2 Transmitting a call ��9-3 DDTransmitting an Individual call ��9-3 DDTransmitting a Group call ��9-3 DDTransmitting a Status Message ��
PAGE 93
9 BIIS 1200 SYSTEM OPERATION BIIS 1200 system operation This function is usable in only the Analog mode. The Binary Interchange of Information and Signalling (BIIS) 1200 standard is one of the best choices to add a data service to an existing system. It enables digital communications, signalling and message exchanges with analog transceivers. You can receive or transmit Individual calls, Group calls, Emergency calls, Status Messages, and Messages.
PAGE 94
9 BIIS 1200 SYSTEM OPERATION Transmitting a call DDTransmitting an Individual call DDTransmitting a Group call (Menu > Signaling/Call > Call List Select) (Menu > Signaling/Call > Call List Select) 1. Push [Menu] to display the Menu screen. 2. Push [P2 (Up)] or [P1 (Down)] to select “Signaling/Call,” then push [OK]. 1. Push [Menu] to display the Menu screen. 2. Push [P2 (Up)] or [P1 (Down)] to select “Signaling/Call,” then push [OK].
PAGE 95
9 BIIS 1200 SYSTEM OPERATION Transmitting a call DDTransmitting a Status Message You can transmit a preset Status Message. You cannot transmit a voice call at the same time. NOTE: If the following settings are configured using the CS-F52D programming software, the Status Message can be automatically transmitted when: ••The transceiver is turned ON. NOTE: Depending on the presetting, the Priority A channel is always used to send Status Messages. LLSet Power ON Status 23 to “Enable.
PAGE 96
9 BIIS 1200 SYSTEM OPERATION Transmitting a call DDTransmitting a Message You can transmit a preset Status Message. You cannot transmit a voice call at the same time. TIP: •• You can also transmit a Status Message through Message. (Menu > Signaling/Call > Message) •• Push [Message] to directly display the “Message” screen in step 6 to the left. •• Hold down [Message] for 1 second to transmit the preset Status Message that is set in the “Message” screen. (Menu > Signaling/Call > Call Menu) 1.
PAGE 97
9 BIIS 1200 SYSTEM OPERATION Transmitting a call DDDirectly entering Message You can directly enter a Message, then send it to the target station or group. TIP: •• The entered Message can be temporary saved. After entering a Message in step 5, push [OK] to display “Save Msg?.” Push [P2 (Up)] or [P1 (Down)] to select “Yes,” then push [OK] to save. However, once the transceiver is turned OFF, the saved Message is deleted. (Menu > Signaling/Call > Write Message) 1. Push [Menu] to display the Menu screen.
PAGE 98
9 BIIS 1200 SYSTEM OPERATION Transmitting a call DDTransmitting an Emergency call DDTransmitting Position data When a BIIS channel is used as the Emergency channel, a BIIS Emergency call can be transmitted in the same way as in 2-Tone, 5-Tone, or NXDNTM signaling. See “Emergency call” for details. (pp.
PAGE 99
9 BIIS 1200 SYSTEM OPERATION Receiving a call DDReceiving an Individual call DDReceiving a Status Message When an Individual call is received: ••The Status indicator lights green. ••“ ” may be displayed or blink, depending on the presetting. ••“ ” is displayed and the mute is released. •• The calling station name (or ID) is displayed while receiving the signal. When a Status Message is received: ••Beeps sound. ••“ ” blinks. •• May vibrate, depending on the presetting.
PAGE 100
9 BIIS 1200 SYSTEM OPERATION Incoming list The transceiver saves a log of the received Individual calls, Group calls, Status Messages, Messages and Emergency calls in the memory, depending on the presetting. Up to 10 Status/Message/Emergency or 5 Voice calls can be saved in the log, and the oldest call record is deleted when an 11th (Status/Message) or 6th (Voice) call is received. However, once the transceiver is turned OFF, the all records are deleted.
PAGE 101
9 BIIS 1200 SYSTEM OPERATION Incoming list DDDeleting the Incoming list The receive call log can be deleted from the Incoming list. (Menu > Signaling/Call > Clear Incoming) 1. Push [Menu] to display the Menu screen. 2. Push [P2 (Up)] or [P1 (Down)] to select “Signaling/ Call,” then push [OK]. Menu Channel/Scan Signaling/Call ► ► 3. P ush [P2 (Up)] or [P1 (Down)] to select “Clear Incoming,” then push [OK]. Signaling/Call Call Menu Clear Incoming ► ► 4.
PAGE 102
Section 10 VOICE RECORDER FUNCTIONS Recording a communication audio ��10-2 Playing back a recorded audio ��10-3 10-1
PAGE 103
10 VOICE RECORDER FUNCTIONS Recording a communication audio This transceiver is equipped with a recorder not only for the receive audio, but also for transmit audio. This function is useful to make a communication record. NOTE: •• The recording will continue until you turn OFF the function, or there is no more free space on the transceiver recording memory. •• When the recording time exceeds 8 minutes, the transceiver continues to record, but it records to a new file.
PAGE 104
10 VOICE RECORDER FUNCTIONS Playing back a recorded audio (Menu > Voice Rec > Play Call Rec) 1. Push [Menu] to display the Menu screen. 2. Push [P2 (Up)] or [P1 (Down)] to select “Voice Rec,” then push [OK]. Menu GPS Voice Rec ► ► 3. P ush [P2 (Up)] or [P1 (Down)] to select “Play Call Rec,” then push [OK]. Voice Rec Call Recorder Play Call Rec ► ► 4. P ush [P2 (Up)] or [P1 (Down)] to select a file, then push [OK].
PAGE 105
Section 11 Bluetooth® OPERATION Bluetooth® Wireless Technology operation �� 11-2 DDElectromagnetic Interference �� 11-2 Turning ON the Bluetooth® function �� 11-3 Pairing with a headset or a data device �� 11-4 Headset settings ��11-6 DD A
PAGE 106
11 Bluetooth® OPERATION Bluetooth® Wireless Technology operation You can connect to other Bluetooth wireless technology enabled devices (Headset or Data) with the installed Bluetooth unit. The communication range of Bluetooth is approximately 10 meters (33 feet). NOTE: The Bluetooth communication range may vary, depending on the environment where you operate the device.
PAGE 107
11 Bluetooth® OPERATION Turning ON the Bluetooth® function (Menu > Bluetooth > Bluetooth) 1. P ush [Menu] to display the “Menu” screen. 2. Push [P2 (Up)] or [P1 (Down)] to select “Bluetooth,” then push [OK]. Menu Bluetooth Vibration ► ► 3. P ush [P2 (Up)] or [P1 (Down)] to select “Bluetooth,” then push [OK]. Bluetooth Bluetooth Bluetooth Reset ► ► 4. P ush [P2 (Up)] or [P1 (Down)] to select “ON,” then push [OK]. Bluetooth ✔ OFF ✔ ON •• The Bluetooth function is turned ON. 5.
PAGE 108
11 Bluetooth® OPERATION Pairing with a headset or a data device Step 1: Enter the Pairing mode (Device) LL See the Bluetooth device’s instruction manual for details. 5. P ush [P2 (Up)] or [P1 (Down)] to select “Headset” or “Data Device,” then push [OK] to start searching. Find Device Type Step 2: Turn ON the Bluetooth function (Transceiver) LL See page 11-3 for details. Headset Data Device Step 3: Search for the device (Transceiver) 1. Push [Menu] to display the “Menu” screen. 2.
PAGE 109
11 Bluetooth® OPERATION Pairing with a headset or a data device Step 4: Connect to the device (Transceiver) 1. Push [P2 (Up)] or [P1 (Down)] to select the headset to connect, then push [OK]. NOTE: The transceiver connects to the last connected device, if the connecting operation is performed on the device side, even if Auto Connect is set to “OFF.” (Menu > Bluetooth > Auto Connect) ••Connects to the headset.
PAGE 110
11 Bluetooth® OPERATION Headset settings DD AF Output (Menu > Bluetooth > Audio Select) You can set the audio output device when a Bluetooth headset is connected. If Audio Select is set to “RMT & SP,” you can hear audio from both a connected Bluetooth headset and the transceiver’s speaker. See page 6-13 for details. DDAbout the VS-3 headset You can set the detailed settings of the optional VS-3 Bluetooth® headset. •• Key Beep (p.
PAGE 111
11 Bluetooth® OPERATION Accepting a pairing request from a Bluetooth® device Step 1: Prepare the Bluetooth device Step 5: Send a Pairing request to the transceiver (Bluetooth device) Select the transceiverʼs Bluetooth unit name to send a pairing request. Step 2: Turn ON the Bluetooth function (Transceiver) LL See page 11-3 for details. ••The Bluetooth device sends a pairing request. LL See the device’s instruction manual for details.
PAGE 112
11 Bluetooth® OPERATION Accepting a pairing request from a Bluetooth® device 4. P ush [P2 (Up)] or [P1 (Down)] to select “Connect,” then push [OK]. PC1 Connect Disconnect Connecting LL If the Serial Port Access Authorization screen is displayed when using a PC, accept it. See the deviceʼs instruction manual for details. •• After the transceiver and device connection has succeeded, “✔” is displayed beside the device icon. Device List Find Device PC1 ► 5.
PAGE 113
11 Bluetooth® OPERATION Disconnecting from a Bluetooth® device You can disconnect from a Bluetooth device without cancelling the pairing. TIP: You can reconnect to the Bluetooth device displayed on the screen again by doing the following steps. (Menu > Bluetooth > Device List) 1. P ush [P2 (Up)] or [P1 (Down)] to select the Bluetooth device to connect, then push [OK]. 1. P ush [Menu] to display the “Menu” screen. 2. Push [P2 (Up)] or [P1 (Down)] to select “Bluetooth,” then push [OK].
PAGE 114
11 Bluetooth® OPERATION Deleting a Bluetooth® device from the pairing list You can delete a Bluetooth device from the “Device List” screen. Before deleting a connected Bluetooth device, disconnect it. (p. 11-9) (Menu > Bluetooth > Device List) 1. P ush [Menu] to display the “Menu” screen. 2. Push [P2 (Up)] or [P1 (Down)] to select “Bluetooth,” then push [OK]. Menu Bluetooth Vibration ► ► 3. P ush [P2 (Up)] or [P1 (Down)] to select “Device List,” then push [OK].
PAGE 115
11 Bluetooth® OPERATION Resetting the installed Bluetooth® unit You can reset the installed Bluetooth unit. You should reset the unit if you have some troubles during Bluetooth operation. NOTE: Before resetting, the Bluetooth function must be turned OFF. Otherwise, resetting cannot be done. (Menu > Bluetooth > Bluetooth Reset) 1. P ush [Menu] to display the “Menu” screen. 2. Push [P2 (Up)] or [P1 (Down)] to select “Bluetooth,” then push [OK]. Menu Bluetooth Vibration ► ► 3.
PAGE 116
11 Bluetooth® OPERATION The maximum number of paired devices You can pair two types of the Bluetooth devices: Headset and Data devices. Up to 8 Bluetooth devices can be paired.
PAGE 117
Section 12 OTHERS Displaying the transceiver’s firmware information ��12-2 LCD Check ��12-3 Copying data from a transceiver ��12-4 DDConnecting ��12-4 DDCopying data ��12-4 1
PAGE 118
12 OTHERS Displaying the transceiver’s firmware information You can display the transceiver firmware’s information. ( Menu > Information > Firmware Info) 1. Push [Menu] to display the Menu screen. 2. Push [P2 (Up)] or [P1 (Down)] to select “Information,” then push [OK]. Menu Utility Information ► ► 3. P ush [P2 (Up)] or [P1 (Down)] to select “Firmware Info,” then push [OK]. Information Firmware Info ► Own ID ► 4.
PAGE 119
12 OTHERS LCD Check You can check whether or not the LCD displays correctly. ( Menu > Display > LCD Test) 1. Push [Menu] to display the Menu screen. 2. Push [P2 (Up)] or [P1 (Down)] to select “Display,” then push [OK]. Menu Display Utility ► ► 3. P ush [P2 (Up)] or [P1 (Down)] to select “LCD Test,” then push [OK]. Display Contrast LCD Test ► ► •• The transceiver displays the Test screen. LLIf the LCD displays correctly, the screen is all black, as shown below. 4.
PAGE 120
12 OTHERS Copying data from a transceiver This section describes how to copy data from a Master transceiver to a Sub transceiver using the optional OPC-1870 zone copy cable. NOTE: Before copying, set Transceiver Data Out to “ON” using the CS-F52D programming software. (Common > Security Setting > Security) DDConnecting DDCopying data Before copying, connect the Master and Sub transceivers using the optional OPC-1870.
PAGE 121
Section 13 OPTIONS HM-222 speaker microphone ��13-2 DDAttaching ��13-2 MB-136 belt clip ��13-3 DDMB-136 contents ��13-3 DDAttaching ��
PAGE 122
13 OPTIONS HM-222 speaker microphone Belt clip [Emer] Microphone [PTT] Earphone jack Speaker Turn OFF the transceiver before attaching or detaching the microphone You can connect an earphone (user supplied) to the earphone jack on the microphone. NOTE: •• NEVER immerse the connector in water. If the connector becomes wet, BE SURE to dry it before attaching to the transceiver. •• The microphone element is located at the top left of the speaker microphone, as shown in the illustration above.
PAGE 123
13 OPTIONS MB-136 belt clip DDMB-136 contents Belt clip Base clip DDAttaching Base clip 1. Detach the battery pack, if attached. (p. 1-3) 2. Slide the base clip in the direction of the arrow until the clip locks and makes a “click” sound. 3. Attach the battery pack to the transceiver. (p. 1-3) Battery pack 4. Clip the belt clip on your belt. 5. Insert the transceiver upsidedown into the belt clip until the base clip is fully inserted in the groove.
PAGE 124
13 OPTIONS MB-136 belt clip DDDetaching 1. T urn the transceiver upsidedown in the direction of the arrow and pull it out of the belt clip. NOTE: Hold the transceiver firmly when removing the transceiver from the belt clip. 2. Detach the battery pack. (p. 1-3) 3. L ift up the tab on the base clip (q), and then slide the clip in the direction of the arrow (w). w BE CAREFUL! Do not break your fingernail.