Instructions for use
These instruction shall be available on website docs.kitchenaid.
Installation diagrams 4
61 1 N.B. For the semi-flush mount version the 1.5 mm milling is not necessary. 2 +1 381 0 +1 0 R1 +1 490 510 1 380 511 0 R1 +1 360 0 5 1.
SEAL SEALANT FRONT INDUCTION INDUCTION AIR SEAL SEALANT AIR 6
Safety instructions IMPORTANT TO BE READ AND OBSERVED can get hot. Very young children (0-3 years) should be kept away from the appliance. Young children (3-8 years) should be kept away from the appliance unless continuously supervised. Children from 8 years old and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge can use this appliance only if they are supervised or have been given instructions on safe use and understand the hazards involved.
conformity with national electrical safety standards. Do not use extension leads, multiple sockets or adapters. The electrical components must not be accessible to the user after installation. Do not use the appliance when you are wet or barefoot. Do not operate this appliance if it has a damaged power cable or plug, if it is not working properly, or if it has been damaged or dropped.
on the product or on the The symbol accompanying documentation indicates that it should not be treated as domestic waste but must be taken to an appropriate collection centre for the recycling of electrical and electronic equipment. ENERGY SAVING TIPS Make the most of your hot plate's residual heat by switching it off a few minutes before you finish cooking. The base of your pot or pan should cover the hot plate completely; a container that is smaller than the hot plate will cause energy to be wasted.
Eco design declaration This appliance meets the eco design requirements of European regulation N. 66/2014, in conformity to the European standard EN 60350-2. Before use IMPORTANT: The cooking zones will not switch on if pots are not the right size. Only use pots bearing the symbol “INDUCTION SYSTEM” (Figure opposite). Place the pot on the required cooking zone before switching the hob on.
Installation After unpacking the product, check for any damage during transport. In case of problems, contact the dealer or the After-Sales Service. For built-in dimensions and installation instruction, see the pictures in page 5. PREPARING THE CABINET FOR FITTING WARNING -- The lower part of the product must not be accessible after installation. -- Do not fit the separator panel if an undertop oven is installed.
Electrical connection For direct connection to the network it is necessary to fit an omnipolar switch of a suitable size to ensure disconnection of he network with a contact opening distance that allows complete disconnection in the conditions of the overtension category III, compliant with the installation regulations (the yellow/green earth wire must not be interrupted). The omnipolar socket or switch must be easy to reach when the appliance is installed. N.B.
Instructions for use On/off of the Touch Control 6 8 6 8 8. 8. 8. 5 1 4 7 2 3 1. 2. 3. 4. 5. 6. 7. 8. On/off Selection decimal points or association with the timer Cooking area selection Power increase Power decrease Timer display Cooking point display Selection decimal points or association with the timer The electronic Touch Control is activated by means of the ON/OFF button and switches from the OFF mode to the Standby mode. To do so it is necessary to press the ON/OFF button for 1 second.
Instructions for use Automatic power down (limiting the working time) The limitation of the working time is a function of the touch control, for turning off the generator. In relation to the cooking level set, each cooking point is turned off after a certain maximum operating time unless the set cooking time has been changed.
Instructions for use Setting the timer value: when a timer has been selected, you can change the timer value using the plus or minus keys. If a timer value has not been set, pressing the minus key will set a value of 30 minutes, which can then be changed. By holding down the plus or minus key longer, the set value will change faster. At a setting value of 99 or 01, the automatic repeat will automatically stop. Turning off the timer early: You can turn off the timer by setting the timer value to 00.
Instructions for use The power required to activate the booster function could be too high and, as a result, the integrated powermanagement feature will reduce the power of the other cooking point of the same induction module; this is indicated to the user by the flashing of the assigned display, allowing a correction time of 3 seconds before the power is reduced to the necessary cooking level. For each cooking point, the Booster function lasts 5 minutes.
After-Sales Service Before contacting the After-Sales Service 1. Switch the appliance off and then on again it to see if the problem has been eliminated. If the problem persists after the above checks, contact the nearest After-Sales Service. Always specify: • a brief description of the fault; • the product type and exact model; • the Service number (the number after the word Service on the rating plate), located under the appliance (on the metal plate). • your full address; • your telephone number.
WHIRLPOOL EMEA S.P.A. Via Carlo Pisacane n.
