Installation guide

ManualsBrandsKitchenAid ManualsMicrowave OvenKHMS2056SBL0

MICROWAVE

HOOD

COMBINATION

INSTALLATION

INSTRUCTIONS

This

product

suitable

for

use

above

electric

gas

cooking

products

and

including

36"

(91.4

cm)

wide.

For

gas

cooktop,

recommend

that

the

combined

cooking

surface

rating

does

not

exceed

50,000

BTU/hr.

See

“Installation

Requirements”

section

for

further

notes.

These

installation

instructions

cover

different

models.

The

appearance

your

particular

model

may

differ

slightly

from

the

illustration

these

installation

instructions.

Table

Contents

MICROWAVE

HOOD

COMBINATION

SAFETY

.....:sesssssseetenees

INSTALLATION

REQUIREMENTS

TOOIS

ANd

Parts...

cesccccesecceseeeseeeessseecnseeeesseeesseuseseeeeeaseeeneeenaeees

Location

Requirements...

cee

eeeeseeeceeseeeeeeeeeneseneventeneesenerenevnees

Product

DIMENSIONS

oo...

eee

eer

eee

reneee

tere

eeeeterneeeeeee

Electrical

Require

Ment

........c.cceeceeeeeeceeeceeteneeeeneceeseneveneesnennereneees

INSTALLATION

INSTRUCTIONS

......cecssseseesssesseseeseesnnenenseeserensaners

Remove

Mounting

Plate

......ccccccccccccceeesenceeereceesereteereneveneesneenereneees

Convert

Microwave

Oven

External

Venting

......0.

eee

Locate

Wall

Stud

(S)

02...

eee

cece

scene

ceeeeeereneeeene

tee

reneveneesnenereneees

Mark

Rear

Walll....ccccccceceseeseeceeceeeeseeneecenereneeeesanevaesneveneesneenereneees

Drill

Holes

Rear

Walll.....cccccccececceeeeeceeceeveeeeeeesenecenerenteneeseneenereneees

Attach

Mounting

Plate

Wall

0.0...

eee

eee eee

eee

eeee

rene

reeeeeeeeneraee

Prepare

Upper

Cabinet

.....cccceecececeeeeeceeceeeeeeeeeneceneventeneesenerenevnees

Install

the

Microwave

OVEN

......e

cee

ceeceeceeeeeeeereneenereneesnenerenerenees

Complete

Installation

.......cccccccceccccceeteeceneeeseeseneenereneeneveneesnernereneees

VENTING

DESIGN

SPECIFICATIONG........ssscecsessseeeereseeseeerenneneee

ASSISTANCE

Replacement

Parts

......ccccc

cece

ececee

eceeceesoeecneeeseseesseeteeenenae

MICROWAVE

HOOD

COMBINATION

SAFETY

Your

safety

and

the

safety

others

are

very

important.

have

provided

many

important

safety

messages

this

manual

and

your

appliance.

Always

read

and

obey

all

safety

messages.

This

the

safety

alert

symbol.

This

symbol

alerts

you

potential

hazards

that

can

kill

hurt

you

and

others.

All

safety

messages

will

the

safety

alert

symbol

and

either

the

word

“DANGER?”

“WARNING.”

These

words

mean:

You

can

killed

seriously

injured

you

don't

immediately

DANG

instructions.

You

can

killed

seriously

injured

you

don't

AWARNING

instructions.

All

safety

messages

will

tell

you

what

the

potential

hazard

is,

tell

you

how

reduce

the

chance

injury,

and

tell

you

what

can

happen

the

instructions

are

not

followed.

W10117077

Summary of content (12 pages)

PAGE 1
MICROWAVE HOOD COMBINATION INSTALLATION INSTRUCTIONS This product is suitable for use above electric or gas cooking products up to and including 36" (91.4 cm) wide. For gas cooktop, we recommend that the combined cooking surface rating does not exceed 50,000 BTU/hr. See “Installation Requirements” section for further notes. These installation instructions cover different models. The appearance of your particular model may differ slightly from the illustration in these installation instructions.
PAGE 2
INSTALLATION REQUIREMENTS The microwave oven is set for recirculation installation. For external (wall or roof) venting, see “Venting Design Specifications” section. ‘Tools and Parts Check the opening where the microwave oven will be installed. The location must provide: Tools Needed Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. m mg mg Minimum one 2" x 4" (60.8 x 101.
PAGE 3
Installation Dimensions NOTE: The grounded 3 prong outlet must be inside the upper cabinet. See “Electrical Requirements” section. ® fo oLe ra eee “ue ' | i ft | Electrical Shock Hazard Plug into a grounded 3 prong outlet. 33" (83.2 em) 12" (30.5 cm) min. typical’ 13" (33.0 cm) max. Do not remove ground prong. Do not use an adapter. 69" (175.3 cm) min. v Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock.
PAGE 4
INSTALLATION INSTRUCTIONS move Mounting Plate NOTE: To avoid possible damage to the work surface, cover the work surface. 1. 2 Remove any remaining contents from the microwave oven cavity. » A th ti late memove tne mounting plate b li Dy peeling olf ff the stri the Strips OF ft tape that attach it to the back of the microwave oven, and set the i i mounting plate aside. % The microwave oven is set for recirculation installation.
PAGE 5
When the vent deflector is as far back as it can easily slide, flip it so that the wide side is to the back of the microwave oven, 3. and the narrow side (with holes) is down. The vent deflector 4. holes should align with mounting holes in the vent opening, as shown in inset. Save the cover for possible change of venting method future. in the Position the damper assembly so that the long tab slides into the slot on the right side of the damper vent opening, as shown.
PAGE 6
NOTE: If no wall studs exist within the cabinet opening, install the microwave oven. See illustrations in “Possible Wall Stud Configurations.” Using a stud finder, locate the edges of the wall stud(s) within the opening. 2. Mark the center of each stud, and draw a plumb line down each stud center. See illustrations in “Possible Wall Stud Configurations.” Possible Wall Stud Configurations These depictions show examples of preferred installation configurations with the mounting plate.
PAGE 7
Wall Venting Installation Only stud, preferably 2, using a minimum 1. Centerline of 1 lag screw, preferably 2. Upper cabinet bottom Using measuring tape, find and clearly mark the vertical centerline of the opening. t 4 ¥" (1 cm) 4" (10.2 cm) 6" (15.2 cm) A. Centerline 2. Mark the centerline 3/8" (1 cm) down from the bottom edge of the upper cabinet.
PAGE 8
Attach Mc Wall Stud at One Corner Hole (Figure 3) Plate to Wall NOTE: Secure the mounting plate to the wall at both bottom corner holes drilled into the wall studs and/or drywall using either 1/4-20 x 3" round-head bolts and toggle nuts or 1/4 x 2" lag With the support tabs of the mounting plate insert a 1/4-20 x 3" round-head bolt through that fits over the 3/4" (19 mm) hole drilled in “Installation for One Wall Stud at One Corner Holes in Rear Wall” section. screws.
PAGE 9
5. Cut the 1%" (3.8 cm) diameter hole at the circular shaded area “G” on the template. This hole is for the power supply cord. NOTE: If upper cabinet is metal, the supply cord bushing needs to be installed around the supply cord hole, as shown. B A. Mounting plate B. Support tabs A. Metal cabinet B. Power supply cord bushing 6. 4. With front of microwave oven still tilted, thread power supply cord through the power supply cord hole in the bottom of the upper cabinet. 5.
PAGE 10
. With the microwave oven centered, and with at least one person holding it in place, insert bolts through upper cabinet into microwave oven. Tighten bolts until there is no gap between upper cabinet and microwave oven. 2. Connect vent to damper assembly. NOTES: m Some upper cabinets may require bolts longer or shorter than 3" (7.6 cm). Longer or shorter bolts are available at most hardware stores. gm Overtightening bolts may warp the top of the microwave oven.
PAGE 11
VENTING DESIGN SPECIFICATIONS This section is intended for architectural designer and builder/contractor reference only. NOTES: mg Vent materials needed for installation are not provided with microwave hood. We do not recommend using a flexible metal vent. To avoid possible product damage, be sure to vent air outside, unless using recirculation installation. Do not vent exhaust air into concealed spaces, such as spaces within walls or ceilings, attics, crawl spaces or garages.
PAGE 12
Recommended Vent Length A 3%" x 10" (8.3 x 25.4 cm) rectangular or 6" (15.2 cm) round vent should be used. The total length of the vent system including straight vent, elbow(s), transitions and wall or roof caps must not exceed the equivalent of 140 ft (42.7 m) for either type of vent. See “Recommended Standard Fittings” section for equivalent lengths. For best performance, use no more than three 90° elbows.