INSTALLATION INSTRUCTIONS.
-. INTRODUCTION Please read all instructions in-iall this product. thoroughly before installing Microwave/Hood If a new electrical outlet is required, it should be connected -1 is installed. by a qualified System.
MOUNTING Microwave/Hood SPACE System requires mounting space on a wall as shown ,30” below. OR MORE FROM COOKING SURFACE I BACKSPLASH 66” OR MORE FROM FLOOR t- J For removal of the Microwave/Hood System bottom cover for cleaning or servicing, a 2-inch space necessary between the top of the range backsplash and the bottom of the Microwave/Hood System.
. WALL CONSTRUCTION Microwave/Hood System should be mounted against and supported by a flat, vertical wall: If wall is not flat, use spacers to fill gaps. Mounting plate must be flat for proper installation. Wall construction should be a minimum of 2” x 4” wood studding and 3/S” or more thick dry wall or plaster/lath. The unit must be attached to a minimum of one 2” x 4” wall stud. For proper installation, the wal-I must be capable of supporting weight of product and load weight allowance of SO pounds).
. ELECTRICAL SERViCE Visual check after unpacking. Remove all packing material from the oven cavity. Check the oven for any damage, such as misaligned door, damaged ,gaskets around door or dents inside the oven cavity or on the door. of fhere is any damage, please do not operate the oven until it has been checked by an Authorized KitchenAid Servicer and any repairs made, if necessary. GROUNDING INSTRUCTIONS: This appliance must be grounded.
HOOD Outside EXHAUST ventilation requires DUCT HOOD EXHAUST EXHAUST CONNECTION: The 3-x” x 10” rectangular duct. hood DUCT. exhaust Read the following has been If round duct is required, a rectangular-to-round less than a 6” diameter duct. transition designed adaptor carefully. to mate with a standard must be used.
‘TOOLS RECOMMENDED Phillips l-1/2” Pencil Screw -Driver Electric Drill 5/8”, 3/32” Drill Wood Measure Bit Tape Bit Saw to cut exhaust Protective FOR INSTALLATION drop cloth opening (if needed) for product and range. You may use part of carton INSTALLATION The installation hardware for protectim. HARDWARE ( @ - @ ) packed NAME I @ Wood Screw 5x30mm 0 Toggle Bolts 3/16 inch 0 Screw 5x55mm @ Flat Washer 30mm Dia.
PREPARATION OF PRODUCT REMOVING MOUNTING PLATE 1. Use a portion of the carton or some other material to protect the outercase from being damaged. 2. Stand the unit on its side as shown in Fig. 1. FRONT SIDE / / / CREASE FILTER OPENINGS \ Figure 1 3. Remove and save two hexagonal Philiips head screws (inside grease filter openings) (Fig. 2).
LOWER HOOKS LEVERS SLIDERS Figure 3 4. Pull out two levers to release surface of outercase. sliders from hooks. This action Familiarize yourself with the operation of the mountrng cedure for mounting the unit to the wall. Gently pull mounting (Mounting plate plate is attached toward will release at both upper plate from back levers so you will be aware of the proper you and slide it to the right.
VENTILATION SYSTEM .: MICROWAVE/HOOD OF VENTILATION Select a. b. c. the type SYSTEM IS DESIGNED SYSTEMS. required for your OUTSIDE VENTILATION: OUTSIDE VENTILATION: RECIRCULATING: FOR ADAPTATION TO THE FOLLOWING THREE (3) TYPES installation. Vertical Exhaust Horizontal Exhaust Non-Vented, ductless installation requires use of charcoal filters packed with product.
B. OUTSIDE VENTILATION: Horizontal Exhaust 1. Remove and save 9 screws. Remove rear stay (Fig. 5). Figure 5 2. Withdraw hood fan unit carefully (Fig. 6). Figure 6 3. Rotate hood fan unit ‘/4 turn (Fig.
4. Replace hood side inserted Be careful fan unit into oven into opening -not unit with left corner first, right corner to pinch the lead wire next. between the back plate and hood fan unit (Fig. 8). Figure 8 5. Replace the rear stay. First, attach rear stay to unit with Make the fan sure openings Safety blades are visible in the rear stay before Screw improper is located installation. (Fig. 9). 2 screws through on the rear stay to prevent Do not remove this screw.
t. RECIRCULATING: I. Remove Non-Vented, and save 9 screws. Ductless Remove rear stay. (Fig. 5 pg. 11). 2. Withdraw hood fan unit. (Fig. 6 pg. 11). 3. Change retainer 4. Rotate lead wire holding to right side wire hood fan unit position from left side wire (Fig. 11). retainer so exhaust opening faces in, to- Figure 11 wards the upper side of the oven. Replace hood fan unit shown (Fig. 12).
PREPARATION MOUNTING OF WALL AND TOP CABINET I’ TEMPLATES CAUTION: THIS PRODUCT INSTRUCTIONS CANNOT BE PROPERLY ON BOTH TEMPLATES. Read and follow mounting information printed matters packed witlithis oven. WALL AND INSTALLED on both Top Cabinet WITHOUT REFERRING and Wall Templates. TO MOUNTING Templates are included in the TOP CABINET 1. The mounting area on top cabinet and wall must be capable of supporting a minimum of 140 pounds.
-MOUNTING PLATE INSTALLATION 1. Separate 2. Insert toggle bolts from toggle one toggle bolt nuts. into each hole on the mounting plate (these holes correspond to holes A, B, C and D of the Wall Template) and put toggle nut onto the toggle (Fig. 13). If hole bolt toggle is located in a stud, do not use these two (2) steps. If MOUNTING/ bolt. 3. If using horizontal method exhaust follow other than horizontal 1. Attach Backdraft ing plate with OUTSIDE continue to step 4. Damper assy.
PRODUCT INSTALLATION 1. Place Styrofoam packing blocks (2 pieces) on top surface of range/cooktop Figure 16 2. Place microwave/hood 3. Thread power supply system on top of Styrofoam cord through 4. Using two (2) people,hang P- xqsed to the wall. unit slightly 6. Pull levers down. blocks the hole at the bottom the unit on the hooks out from the mounting Press unit to mounting as shown of top cabinet. at the bottom of the mounting plate. plate. Push levers back up. 16 in Fig. 16.
7. Check to be sure the unit is secure to the mounting head screws to levers (inside plate at both upper and lower your support. 8. Screw hexagonal Phillips grease filter opening) Figure 18 9. Check 10. Replace that both levers (a) are securely fixed. If not, tighten grease filters. 17 screws (Fig. 18). (Fig. 18).
10. Use adjusting screws fc) and flat washers (d) for gaps between top cabinet and unit (Fig. 19). Id) Figure 19 11:Make a bundle of power supply cord, A short power supply cord is provided face or from becoming tangled. Extension cords are available then fix it to cabinet to reduce using cord the risks resulting and may be used if care is exercised hook from contacting in their the cooking sur- use.
. CHECK LIST FOR INSTALLATION 1. Make sure unit has been installed 2. Remove 3. Plug in power 4. Read Use and Care Manual. 5. Keep installation all packing material according to instructions from the oven. cord. instructions for the local electrical inspector’s ACCESSORIES 1. CHARCOAL FILTER KIT (307931). Filter is used for recirculating 19 exhaust. use.
km MS032 KitchenAid, Inc. (f/74735 St.
