Food Processor 5KFP1333, 5KFP1444 INSTRUCTIONS Processador de alimentos KJA13 INSTRUÇÕES 食品加工机 5KFP1333, 5KFP1444 指南 W10508883D_v08.
Table of Contents FOOD PROCESSOR SAFETY Important Safeguards.................................................................................................3 Electrical Requirements-Plastic Models......................................................................5 Electrical Requirements-Metal Models.......................................................................5 Electrical Requirements for Brazil Only.....................................................................6 PARTS AND FEATURES......
ENGLISH FOOD PROCESSOR SAFETY IMPORTANT SAFEGUARDS When using electrical appliances, basic safety precautions should always be followed, including the following: 1. Read all instructions. Misuse of appliance may result in personal injury. 2. To protect against risk of electrical shock, do not put Food Processor in water or other liquid. 3.
FOOD PROCESSOR SAFETY 6. Avoid contacting moving parts. 7. Do not operate any appliance with a damaged cord or plug, or after the appliance malfunctions, or is dropped or damaged in any manner. Return appliance to the nearest Authorized Service Facility for examination, repair, or electrical or mechanical adjustment. 8. The use of attachments not recommended or sold by KitchenAid may cause fire, electric shock, or injury. 9. Do not use outdoors. 10. Do not let cord hang over edge of table or counter. 11.
FOOD PROCESSOR SAFETY Electrical Requirements- Plastic Models Fire Hazard Do not use an extension cord. Doing so can result in death or fire. ENGLISH Volts: 220-240 Volts VAC Hertz: 50/60 Hz NOTE: This Food Processor is equipped with a polarized plug (one blade is wider than the other). To reduce the risk of electrical shock, this plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician.
FOOD PROCESSOR SAFETY Electrical Requirements for Brazil Only Use appropriate outlet type for your appliance plug, as shown below: Residence mains: The mains wires must be of copper with a minimum cross-section per ABNT (NBR-5410.) To protect this appliance and the mains against over loading, this appliance must be connected to a circuit that is protected with a thermo-magnetic circuit breaker. If the household circuit does not include a circuit breaker, contact an electrician to have one installed.
PARTS AND FEATURES Julienne Disc (select models only) ENGLISH Reversible (2 mm and 4 mm) Shredding Disc Externally Adjustable Slicing Disc Thin to Thick Chef’s Accessory Case Disc Adapter Slicing Adapter Drive Adapter 3-Piece Food Pusher Work Bowl Cover with 3-in-1 Feed Tube Work Bowl 945 ml (4-Cup) Mini-Bowl and Mini-Blade Stainless Steel Multipurpose Blade Externally Adjustable Slicing Control Dough Blade Heavy-Duty Base 7 W10508883D_v08.
PARTS AND FEATURES Important parts and accessories included with your new Food Processor are highlighted below. Refer to the following pages for additional details on accessories included with your Food Processor as well as optional accessories you can order separately (some optional accessories included with select models).
ACCESSORIES Disc Assembly Overview There are two different disc adapters included with the food processor. One is used exclusively with the adjustable slicing disc. The other is used with all other discs. Reversible Shredding Disc Slicing Adapter ENGLISH Adjustable Slicing Disc Disc Adapter Drive Adapter Drive Adapter Properly assembled 9 W10508883D_v08.
ACCESSORIES Accessories Selection Guide Not all accessories shown are included with all models.
PREPARING THE FOOD PROCESSOR FOR FIRST USE ENGLISH 2. Lift out the mini-bowl. Before First Use Before using your Food Processor for the first time, wash the work bowl, work bowl cover, mini-bowl, feed tube pushers, discs, and blades either by hand or in the dishwasher (see “Cleaning the Food Processor”). Removing the Work Bowl Cover from the Work Bowl Your Food Processor is shipped with the work bowl cover installed on the work bowl, with the mini-bowl inside the work bowl.
SETTING UP YOUR FOOD PROCESSOR Attaching the Work Bowl 1. Place the Food Processor on a dry, level countertop with the controls facing forward. Do not plug in the Food Processor until it is completely assembled. 2. Place the work bowl on the base, aligning the raised portion with the indentation on the base. The center hole should fit over the power shaft. Attaching the Work Bowl Cover NOTE: Be sure to install the desired accessory before attaching the work bowl cover. 1.
SETTING UP YOUR FOOD PROCESSOR IMPORTANT: The adjustable slicing disc can only be installed in one direction. TIP: You may need to turn the disc/drive adapter until it drops down into place. 4. Install the work bowl cover, being sure it locks into place. 1. With the work bowl installed, place the drive adapter on the power shaft of the base. 2. Holding the adjustable slicing disc by the 2 finger grips, align the pins onto the adjustable slicing disc adapter into the L-slots on the disc.
SETTING UP YOUR FOOD PROCESSOR Installing Other Slicing or Shredding Discs IMPORTANT: The optional julienne and plane/shave discs can only be installed in one direction. When using the reversible shredding disc, have the desired side (medium/fine) facing UP. 3. With the work bowl installed, slide the drive adapter onto the power shaft. TIP: You may need to turn the disc/drive adapter until it drops down into place. 1.
SETTING UP YOUR FOOD PROCESSOR IMPORTANT: The multipurpose blade and dough blade can only be used with the work bowl. 1. Place the blade on the power shaft. 2. Rotate the blade so it falls into place on the power shaft. Installing the Mini-Bowl and Mini-Blade 1. Place the mini-bowl inside the work bowl over the power shaft. Rotate the minibowl until the tabs on the top edge of the bowl drops into the indents on the top of the work bowl. ENGLISH Installing the Multipurpose Blade or Dough Blade 2.
SETTING UP YOUR FOOD PROCESSOR Using the 3-in-1 Feed Tube The 3-in-1 feed tube features a 3-piece food pusher. Use the entire food pusher to process large items, or use the inner portions to create medium-sized or small feed tubes to process smaller items. To slice or shred small items, insert the 3-piece food pusher into the feed tube, then lift out the small pusher to remove. Use the small feed tube and pusher to process small or slender items, like single carrots or celery stalks.
USING YOUR FOOD PROCESSOR 1. To turn on the Food Processor, press the Speed 1 or Speed 2 button. The Food Processor will run continuously and the indicator light will glow. 2. To stop the Food Processor, press the “O” (OFF) button. The indicator light will go out and the blade or disc will stop within a few seconds. 3. Wait until the blade or disc comes to a complete stop before removing the work bowl cover.
USING YOUR FOOD PROCESSOR Removing Processed Foods 5. If using the mini-bowl, grasp and remove the bowl using the finger grips located along the top edge of the bowl. 1. Press the “O” (OFF) Button. 2. Unplug the Food Processor before disassembling. 3. Turn the work bowl cover to the left and remove. 4. If using a disc, remove it before removing the bowl. Holding the disc by the 2 finger grips, lift it straight up. Remove the adapter. 6. Turn the work bowl to the left to unlock it from the base.
CARE AND CLEANING ENGLISH 1. Press the “O”(OFF) Button. 2. Unplug the Food Processor before Cleaning. 3. Wipe the base and cord with a warm, sudsy cloth, and wipe clean with a damp cloth. Dry with a soft cloth. Do not use abrasive cleansers or scouring pads. 4. Please note these BPA-free bowls require special handling. If you choose to use a dishwasher instead of hand washing, please follow these guidelines. -- All parts are top rack dishwasher safe. -- Avoid laying the bowl on its side.
TIPS FOR GREAT RESULTS To finely chop citrus peel: With sharp knife, peel colored portion (without white membrane) from citrus. Cut peel in small strips. Process until finely chopped. To mince garlic or to chop fresh herbs or small quantities of vegetables: With processor running, add food through the feed tube. Process until chopped. For best results, make sure work bowl and herbs are very dry before chopping.
To slice or shred fruits and vegetables that are small, such as strawberries, mushrooms, and radishes: Position food vertically or horizontally in layers within the feed tube. Fill feed tube in order to keep food positioned properly. Process, using even pressure. Or use the small feed tube in the two-piece food pusher. Position food vertically in the tube and use the small food pusher to process food. To slice uncooked meat or poultry, such as stir-fry meats: Cut or roll food to fit feed tube.
TIPS FOR GREAT RESULTS • To capitalize on the speed of the processor, drop ingredients to be chopped through the feed tube while the processor is running. • Different foods require varying degrees of pressure for best shredding and slicing results. In general, use light pressure for soft, delicate foods (strawberries, tomatoes, etc.), moderate pressure for medium foods (zucchini, potatoes, etc.), and firmer pressure for harder foods (carrots, apples, hard cheeses, partially frozen meats, etc.).
TROUBLESHOOTING Food Processor doesn’t run: • Make sure that the bowl and lid are properly aligned and locked in place and the large food pusher is inserted in the feed tube. • When using the large feed tube opening, make sure that food is not above the Max Fill line on the feed tube. Max Fill line on feed tube Food Processor not shredding or slicing properly: • Make sure the raised-blade side of the disc is positioned face up on the common adapter.
W10508883D 08/14 © 2014. All rights reserved. 24 W10508883D_v08.
