Installation guide
4.
Place
burner
grates
over
burners
and
caps
as
shown
in
the
following
illustration.
When
properly
installed,
the
grates
should
not
overlap
the
console.
Freestanding
Ranges
Opening
in
grate
for
wok
insert
is
located
over
left
front
burner.
A.
Opening
in
grate
for
wok
insert
Slide-In
Ranges
Large
flange
with
rounded
corner
must
be
at
the
rear
corner
of
the
cooktop.
A.
Large
flange
with
rounded
corner
5.
Plug
in
range
or
reconnect
power.
“Clock-Enter
Time”
should
appear
in
the
display.
For
further
information,
please
refer
to
the
user
instructions
located
in
the
Use
and
Care
Guide.
Initial
lighting
and
gas
flame
adjustments
Cooktop
burners
use
electronic
igniters
in
place
of
standing
pilots.
When
the
cooktop
control
knob
is
turned
to
the
“LITE”
position,
the
system
creates
a
spark
to
light
the
burner.
This
sparking
continues
as
long
as
the
control
knob
is
turned
to
“LITE.”
Check
Operation
of
Cooktop
Burners
Standard
Surface
Burners
Push
in
and
turn
each
control
knob
to
the
“LITE”
position.
The
flame
should
light
within
4
seconds.
The
first
time
a
burner
is
lit,
it
may
take
longer
than
4
seconds
to
light
because
of
air
in
the
gas
line.
18
TripleTier®
Flame
Burner
To
start
simmer
burner:
Push
in
and
turn
control
Knob
to
“LITE.”
The
flame
should
light
within
4
seconds.
The
first
time
a
burner
is
lit,
it
may
take
longer
than
4
seconds
to
light
because
of
air
in
the
gas
line.
To
start
power
burner:
Push
in
control
knob
again
and
turn
to
“POWER
BURNER
HI”
(“DUAL
HI”
on
model
KDSS907XSP)
to
light
the
outer
burner.
The
flame
should
light
within
4
seconds.
The
first
time
a
burner
is
lit,
it
may
take
longer
than
4
seconds
to
light
because
of
air
in
the
gas
line.
If
burners
do
not
light
properly:
mg
Turn
cooktop
control
knob
to
the
“OFF”
position.
m
Check
that
the
range
is
plugged
in
and
the
circuit
breaker
has
not
tripped
or
the
household
fuse
has
not
blown.
m
Check
that
the
gas
shutoff
valves
are set
to
the
“open”
position.
m
Check
that
burner
caps
are
properly
positioned
on
burner
bases.
Repeat
start-up.
If
a
burner
does
not
light
at
this
point,
turn
control
knobs
to
“Off”
and
contact
your
dealer
or
authorized
service
company
for
assistance.
Adjust
Flame
Height
Adjust
the
height
of
top
burner
flames.
The
cooktop
“low”
burner
flame
should
be
a
steady
blue
flame
approximately
44"
(0.64
cm)
high.
———
A
eg
PII
iad
a
Tal
Z.
A.
Low
flame
B.
High
flame
To
adjust
standard
burners:
The
flame
can
be
adjusted
using
the
adjustment
screw
in
the
center
of
the
valve
stem.
The
valve
stem
is
located
directly
underneath
the
control
knob.
=
~~
_
S
—
a
6
A.
Valve
stem
If
the
“low”
flame
needs
to
be
adjusted:
1.
Remove
the
control
knob.
2.
Hold
the
knob
stem
with
a
pair
of
pliers.
Use
a
small
flat-
blade
screwdriver
to
turn
the
screw
located
in
the
center
of
the
control
knob
stem
until
the
flame
is
the
proper
size.
3.
Replace
the
control
knob.
4.
Test
the
flame
by
turning
the
control
from
“LO”
to
“HI,”
checking
the
flame
at
each
setting.