Installation guide
To
adjust
TripleTier®
Flame
burner:
1.
Remove
the
control
knob.
2.
Insert
a
flat-blade
screwdriver
into
adjustment
locations
shown
in
the
following
illustration
and
engage
the
slotted
screw.
Turn
the
screw
until
the
flame
is
the
proper
size.
A.
Simmer
burner
regulation
B.
Power
burner
regulation
3.
Replace
the
control
knob.
4.
Test
the
flame
by
turning
the
control
from
“LO”
to
“HI,”
checking
the
flame
at
each
setting.
1.
Place
your
foot
against
the
bottom
front
of
the
warming
drawer,
and
grasp
the
control
panel
and
range
top
with
two
hands
as
shown.
2.
Slowly
attempt
to
tilt
the
range
forward.
If
you
encounter
immediate
resistance,
the
range
foot
is
engaged
in
the
anti-tip
bracket.
3.
If
the
rear
of
the
range
lifts
more
than ¥"
(1.3
cm)
off
the
floor
without
resistance,
stop
tilting
the
range
and lower
it
gently
back
to
the
floor.
The
range
foot
is
not
engaged
in
the
anti-tip
bracket.
IMPORTANT:
If
there
is
a
snapping
or
popping
sound
when
lifting
the
range,
the
range
may
not
be
fully
engaged
in
the
bracket.
Check
to
see
if
there
are
obstructions
keeping
the
range
from
sliding
to
the
wall
or
keeping
the
range
foot
from
sliding
into
the
bracket.
Verify
that
the
bracket
is
held
securely
in
place
by
the
mounting
screws.
4.
Slide
the
range
forward,
and
verify
that
the
anti-tip
bracket
is
securely
attached
to
the
floor
or
wall.
5.
Slide
range
back
so
the
rear
range
foot
is
inserted
into
the
slot
of
the
anti-tip
bracket.
IMPORTANT:
If
the
back
of
the
range
is
more
than
2"
(5.1
cm)
from
the
mounting
wall,
the
rear
range
foot
may
not
engage
the
bracket.
Slide
the
range
forward
and
determine
if
there
is
an
obstruction
between
the
range
and
the
mounting
wall.
Changes
to
the
gas
supply
must
be
performed
by
a
qualified
service
technician.
If
you
need
assistance
or
service,
refer
to
the
cover
or
the
“Warranty”
section
of
the
User
Instructions,
for
contact
information.
6.
Repeat
steps
1
and
2
to
ensure
that
the
range
foot
is
engaged
in
the
anti-tip
bracket.
If
the
rear
of
the
range
lifts
more
than
2"
(1.3
cm)
off
the
floor
without
resistance,
the
anti-tip
bracket
may
not
be
installed
correctly.
1.
Place
a
rack
in
oven.
2.
Place
level
on
rack
and
check
levelness
of
range,
first
side
to
side;
then
front
to
back.
3.
If
range
is
not
level,
pull
range
forward
until
rear
leveling
leg
is
removed
from
the
anti-tip
bracket.
Use
a
wrench
or
pliers
to
adjust
leveling
legs
up
or
down
until
the
range
is
level.
Push
range
back
into
position.
Check
that
rear
leveling
leg
is
engaged
in
the
anti-tip
bracket.
NOTE:
Range
must
be
level
for
satisfactory
baking
performance.
Es
Replace
oven
racks
in
oven
cavity.
Replace
warming
drawer
or
storage
drawer.
Racks
and
ling
Drawer
To
Replace
Warming
Drawer:
1.
Align
the
drawer
glides
with
the
receiving
guides.
2.
Push
drawer
in
all
the
way.
3.
Gently
open
and
close
the
drawer
to
ensure
it
is
seated
properly
on
the
slides.
19