Instructions for use
Installation 4 Product description 6 First time use 7 Programs table 10 Options and functions 11 Loading the racks 12 Daily use 14 Tips 15 Care and maintenance 15 Troubleshooting 17 After-sales service 18
Before using the appliance carefully read Health and Safety guide. Installation ATTENTION: If the appliance must be moved at any time, keep it in an upright position; if absolutely necessary, it may be tilted onto its back. CONNECTING THE WATER SUPPLY ANTI-FLOODING PROTECTION Adaptation of the water supply for installation should only be performed by a qualified technician. The water inlet and outlet hoses may be positioned towards the right or the left in order to achieve the best possible installation.
POSITIONING AND LEVELLING DIMENSIONS, CAPACITY AND STANDBY CONSUMPTION: 1. Position the dishwasher on a level sturdy floor. If the floor is uneven, the front feet of the appliance may be adjusted until it reaches a horizontal position. If the appliance is levelled correctly, it will be more stable and much less likely to move or cause vibrations and noise while it is operating. 2.
Product description APPLIANCE 1 8 9 2 10 3 4 11 5 Service: 6 12 0000 000 00000 7 13 1. 2. 3. 4. 5. 6. 7. Upper rack Foldable flaps Upper rack height adjuster Upper spray arm Dynamic Clean supports Lower rack Cutlery basket 8. 9. 10. 11. 12. 13. Lower spray arm Filter Assembly Salt reservoir Detergent and Rinse Aid dispensers Rating plate Control panel 11. 12. 13. 14.
First time use ADVICE REGARDING THE FIRST TIME USE After the installation, remove the stoppers from the racks and the retaining elastic elements from the upper rack. SETTING MENU 1. 2. 3. 4. 5. Switch on the appliance by pressing the ON/OFF button. Switch off the appliance by pressing the ON/OFF button. Hold down START button for 5 seconds, until you hear a beep. The display shows the first available setting (letter "A"), followed by its value (for example: 3).
FILLING THE SALT RESERVOIR The factory setting is “3” for average water hardness. To change, follow instructions in section “SETTING MENU”. Water Hardness Table °fH °dH Level The use of salt prevents the formation of LIMESCALE on the dishes and on the machine’s functional components. • It is important that the salt reservoir be never empty. • It is important to set the water hardness.
FILLING THE DETERGENT DISPENSER To open the detergent dispenser press button A. Introduce the detergent into the dry dispenser B only. Only use detergent which has been specifically designed for dishwashers. To achieve the best washing and drying results, the combined use of detergent, rinse aid liquid and refined salt is required. We recommend using detergents that do not contain phosphates or chlorine, as these products are harmful to the environment.
Drying phase Programs table Program Detergent Duration Water Energy container of wash consump- consumpprogram tion tion Tub B (h:min)**) (litres/cycle) (kWh/cycle) Available options *) P1 50° 3:10 9 0.93 P2 50-60° 1:25 - 3:00 7 - 14 0.90 - 1.40 P3 Professional 65° - 2:27 16.5 1.70 50° - 1:30 13 1.15 - 0:30 9 0.55 - 2:05 11.5 1.20 0:12 4.5 0.01 1:40 10 1.
Options and functions OPTIONS can be selected directly by pressing the corresponding button (see CONTROL PANEL). If an option is not compatible with the selected program see PROGRAMS TABLE, the corresponding LED flashes rapidly 3 times and beeps will sound. The option will not be enabled. MULTIZONE If there are not many dishes to be washed, a half loading may be used in order to save water, electricity and detergent.
Loading the racks Before loading the baskets, remove all food residues from the crockery and empty the glasses. You do not need to rinse beforehand under running water. Arrange the crockery so that it is held in place firmly and does not tip over; and arrange the containers with the openings facing downwards and the concave/convex parts placed obliquely, thus allowing the water to reach every surface and flow freely.
LOWER RACK For pots, lids, plates, salad bowls, cutlery etc. Large plates and lids should ideally be placed at the sides to avoid interferences with the spray arm. (loading example for the lower rack) The lower rack has tip-up supports which can be used in a vertical position when arranging plates or in a horizontal position (lower) to load pans and salad bowls easily. DYNAMIC CLEAN IN LOWER RACK Dynamic Clean uses the special water jets in the rear of cavity to wash more intensively the high dirty items.
GLASS CARE Dedicated accessory that allows you to safely store different types of stem glasses in the lower rack. It enables cleaning & drying results by allowing an optimised and stable positioning of the glasses. 2 3 1 1 2 3 B A Daily use 1. CHECK WATER CONNECTION Check that the dishwasher is connected to the water supply and that the top is open. 2. LOAD THE RACKS (see LOADING THE RACKS) 3. FILLING THE DETERGENT DISPENSER (see PROGRAMS TABLE). 4.
Tips UNSUITABLE CROCKERY DAMAGE TO GLASS AND CROCKERY • Wooden crockery and cutlery. • Delicate decorated glasses, artistic handicraft and antique crockery. Their decorations are not resistant. • Parts in synthetic material which do not withstand high temperatures. • Copper and tin crockery. • Crockery soiled with ash, wax, lubricating grease or ink. The colours of glass decorations and aluminium/silver pieces can change and fade during the washing process. Some types of glass (e.g.
CLEANING THE FILTER ASSEMBLY Regularly clean the filter assembly so that the filters do not clog and that the waste water flows away correctly. The filter assembly consists of three filters which remove food residues from the washing water and then recirculate the water: to obtain the best washing results, you need to keep them clean. The dishwasher must not be used without filters or if the filter is loose.
Troubleshooting Your dishwasher may not work properly. Before contacting the Service Centre check if the problem can be solved by going through the following list. PROBLEMS POSSIBLE CAUSES SOLUTIONS The appliance has not been plugged in properly. Insert the plug into the socket. The dishwasher won’t Power outage. start or does not respond to The dishwasher door is not closed. commands. It does not respond to commands. The door doesn’t lock. The dishwasher makes excessive noise.
PROBLEMS POSSIBLE CAUSES SOLUTIONS The dishwasher does not fill the water, shows "H2O" Warning or "F06" No water in the water supply or the tap is closed. Make sure there is water in the water supply or the tap running. The inlet hose is bent. Make sure the drain hose is not bent (see INSTALLATION) reprogram the dishwasher and reboot.
Printed in Italy 10/17 400011162613B EN
