5019_718_02006_GB 26-09-2007 11:33 Pagina 1 KCDP 9010/I Instructions for use
5019_718_02006_GB 26-09-2007 11:33 Pagina 2
5019_718_02006_GB 26-09-2007 11:33 Pagina 3 Warnings 4 Safeguarding the environment 5 Instructions for installation and use 6 Extraction Modes 6 Installation 7 Hood description 11 Functioning 11 Maintenance 12 After-Sales Service 14
5019_718_02006_GB 26-09-2007 11:33 Pagina 4 Warnings • This appliance should not be used by children or people with limited physical or mental abilities and with no experience or knowledge of its use, unless they are supervised by someone in charge of their safety or who has taught them how to use the appliance. • Children should not play with the appliance. 1. Do not connect the appliance to the mains supply until the installation is completely finished.
019_718_02006_GB 26-09-2007 11:33 Pagina 5 Warnings Declaration of conformity This product has been designed, manufactured and marketed according to the following: - safety objectives of the “Low Voltage” Directive 2006/95/CE (wich replaces 73/23/CEE and subsequent amendments). - protection requirements of “EMC” Directive 89/336/EEC amended by Directive 93/68/EEC.
5019_718_02006_GB 26-09-2007 11:33 Pagina 6 Instructions for installation and use This is an excessively heavy product and the movement and installation of the hood should be done by at least two or more people. Follow the instructions in this manual carefully. All responsibility is denied for problems, damage or fire to the appliance resulting in failure to comply with the instructions in this manual.
5019_718_02006_GB 26-09-2007 11:33 Pagina 7 Installation The hood comes with plugs suitable for most walls/ceilings. You should however consult a qualified technician to make sure the installation is suitable for your kind of wall/ceiling. The wall/roof should be sufficiently strong to support the weight of the hood. it with some protection where you can place the hood and parts. • Disconnect the hood by turning off the mains switch in the house when connecting the electrics.
5019_718_02006_GB 26-09-2007 11:33 Pagina 8 Installation Fig. 4 • Place the lower support bracket on the perforation layout aligning it with the sketched rectangle. Mark the two external holes, then drill the holes. Remove the perforation layout and insert 2 wall plugs and fix the hood support bracket with 2 5x45mm screws. Fig. 5 • Hang the hood on the lower bracket. • Adjust the distance of the hood from the wall. • Adjust the horizontal position of the hood.
5019_718_02006_GB 26-09-2007 11:33 Pagina 9 Installation • The hood has two identical brackets for attaching the chimney. Attach the first bracket (G – the side with fixing holes facing upwards – see Fig. 6) to the wall next to the ceiling, using the support bracket as a template (the small slots cut in the bracket should coincide with the centre lines previously traced on the wall), mark 2 holes with a pencil, drill the holes and attach the bracket with 2 screws and plugs.
5019_718_02006_GB 26-09-2007 11:33 Pagina 10 Installation • Hook the hood onto the lower bracket. • Fit the hood securely to the wall with screws • Connect the venting pipe (Venting pipe and straps are not provided and must be purchased seperately) to the connection ring found above the motor suction unit. The other end of the pipe should be attached to venting pipe leading to the outside if you are using the extractor in the vented mode.
5019_718_02006_GB 26-09-2007 11:33 Pagina 11 Hood description Fig. 9 1. Control panel 2. Grease filter 3. Handle for unhooking the grease filter 4. Halogen bulbs 5. Steam deflector screen 6. Telescopic chimney 7. Air outlet (only for use with filter version) 8. Perimetric suction panel Functioning Turn to maximum speed when there is a lot of steam in the kitchen.
5019_718_02006_GB 26-09-2007 11:33 Pagina 12 Maintenance Always disconnect the power supply before carrying out any kind of maintenance work. Cleaning The hood should be cleaned regularly both inside and out (at least as often as you carry out maintenance on the grease filters). Use a damp cloth with mild cleaning products. Avoid using harsh products.
5019_718_02006_GB 26-09-2007 11:33 Pagina 13 Maintenance Carbon filter (only in recirculation mode) Fig. 12 The Carbon filter absorbs any unpleasant smells produced when cooking. The carbon filter can be washed every two months in hot water with suitable cleaning fluids, or in the dishwasher at 65°C (when washing in the dishwasher, do a full wash without any plates inside). Shake off any excess water without damaging the filter, then place it in the oven for 10 minutes at 100°C to dry it off completely.
5019_718_02006_GB 26-09-2007 11:33 Pagina 14 After-Sales Service Before calling Customer Care Centre: 1. See if you can solve the problem yourself with the help of the “Troubleshooting guide”. 2. Switch off the hood for a few minutes and restart it to see if the problem has cleared itself. 3. If the malfunction persists, call the Customer Care Centre Service.
5019_718_02006_GB 26-09-2007 11:33 Pagina 15
5019_718_02006_GB 26-09-2007 Printed in Italy 05/07 5019 718 02006 11:33 Pagina 16 n GB
