Stand Mixer INSTRUCTIONS ࡳ㛑ৄᓣ᧙ᢠᴎ 䇈ᯢк
Table of Contents Stand Mixer Safety............................................................................................................................ 3 Important Safeguards ................................................................................................................... 3,4 Troubleshooting Problems ............................................................................................................... 5 About Your Mixer Bowl Lift Stand Mixer Features ....................
English Stand Mixer Safety IMPORTANT SAFEGUARDS When using electrical appliances, basic safety precautions should always be followed, including the following: 1. Read all instructions. 2. To avoid risk of electrical shock, do not put Stand Mixer in water or other liquid. 3. Be sure that the prongs on the plug of the unit mate with the electrical wall receptacle into which it will be plugged. Observation of proper grounding techniques and local electrical codes is required. 4.
Stand Mixer Safety IMPORTANT SAFEGUARDS When using electrical appliances, basic safety precautions should always be followed, including the following: 10. Do not operate any appliance with a damaged cord set or after the appliance has been dropped or damaged in any manner. Return appliance to the nearest authorized service center for examination, repair, or adjustment. 11. The use of attachments not recommended by KitchenAid may cause fire, electrical shock, or injury. 12. Do not use outdoors. 13.
Please read the following before calling your service center. 1. The Stand Mixer may become warm during use. Under heavy loads with extended mixing time periods, you may not be able to comfortably touch the top of the Stand Mixer. This is normal. 2. The Stand Mixer may emit a pungent odor, especially when new. This is common with electric motors. 3. If the flat beater hits the bowl, stop the Stand Mixer. See the Beater to Bowl Clearance section.
Bowl Lift Stand Mixer Features Motor Head Speed Control Lever Attachment Hub (see the Attachments section) Attachment Knob Beater Height Adjustment Screw Bowl Lift Lever (not shown) Beater Shaft Bowl Support Locating Pins Bowl Handle (style may vary depending on model) 6,9L (7 qt) Stainless Steel Bowl Stainless Steel Whip Spiral Dough Hook Flat Beater Pouring Shield (available on some models) 6
To Lower Bowl 1. Rotate lever back and down. To Remove Bowl 1. Be sure speed control is 0 (OFF) and Stand Mixer is unplugged. 2. Place bowl lift handle in down position. 3. Remove flat beater, wire whip, or spiral dough hook. 4. Grasp bowl handle and lift straight up and off locating pins. To Attach Flat Beater, Wire Whip, or Spiral Dough Hook 1. Slide speed control to 0 (OFF) and unplug. 2. Slip flat beater on beater shaft. To Attach Bowl 1.
Using the Pouring Shield* Attaching the Pouring Shield 1. Make sure the speed control lever is set to the 0 (OFF) position. 2. Unplug the Stand Mixer. 3. Attach desired accessory and raise the mixing bowl. 4. Slide pouring shield collar around beater shaft, centering collar over rim of bowl. Pouring Chute Using the Pouring Shield Removing the Pouring Shield Pour ingredients into the mixing bowl through the chute portion of shield. 1. Make sure the speed control lever is set to the 0 (OFF) position.
Using Your KitchenAid Attachments Flat Beater for normal to heavy mixtures: biscuits crumpets meat loaf mashed potatoes Wire Whip for mixtures that need air incorporated: eggs egg whites heavy cream boiled frostings sponge cakes mayonnaise some candies English cakes creamed frostings candies cookies pie pastry Spiral Dough Hook for mixing and kneading yeast doughs: breads rolls coffee cakes buns Mixing Time Your KitchenAid Stand Mixer will mix faster and more thoroughly than most other electric stand
Care and Cleaning Bowl, stainless steel flat beater, wire whip, and spiral dough hook may be washed thoroughly with soap and hot water and rinse completely before drying. Do not store beaters on shaft. NOTE: Always be sure to unplug stand mixer before cleaning. Wipe stand mixer with a soft, damp cloth. Do not use household/commercial cleaners. Do not immerse in water. Wipe off beater shaft frequently, removing any residue that may accumulate.
Speed Control Guide - 10 Speed Stand Mixers Speed Used for Accessories Description 1 Stirring For slow stirring, combining, mashing, starting all mixing procedures. Use to add flour and dry ingredients to batter, and add liquids to dry ingredients. Do not use Speed 1 to mix or knead yeast doughs. 2 Slow Mixing, Kneading For slow mixing, mashing, faster stirring.
Mixing Tips Converting Your Recipes for the Stand Mixer The mixing instructions for recipes in this book can guide you in converting your own favorite recipes for preparation with your KitchenAid Stand Mixer. Look for recipes similar to yours and then adapt your recipes to use the procedures in the similar KitchenAid recipes. For example, the quick mix method (sometimes referred to as the dump method) is ideal for simple cakes.
Whipped Cream Place room temperature egg whites in clean, dry bowl. Attach bowl and wire whip. To avoid splashing, gradually turn to designated speed and whip to desired stage. See chart below. Pour cold whipping cream into chilled bowl. Attach bowl and wire whip. To avoid splashing, gradually turn to designated speed and whip to desired stage. See chart below. AMOUNT SPEED 1 egg white........GRADUALLY to 10 AMOUNT SPEED 50 mL (1/4 cup) .....GRADUALLY to 10 125 mL (1/2 cup) ...
Bread Making Tips Making bread with a mixer is quite different from making bread by hand. Therefore, it will take some practice before you are completely comfortable with the new process. For your convenience, we offer these tips to help you become accustomed to bread-making the KitchenAid brand way. Always use the PowerKnead Spiral Dough Hook to mix and knead yeast doughs. Use Speed 2 to mix or knead yeast dough.
Attachments and Accessories See the Use and Care Guide that came with your Stand Mixer attachments for speed settings and operating time. Attachment Power Shaft English General Information KitchenAid Attachments are designed to assure long life. The attachment power shaft and hub socket are of a square design, to eliminate any possibility of slipping during the transmission of power to the attachment. The hub and shaft housing are tapered to assure a snug fit, even after prolonged use and wear.
General Instructions To Attach 1. Turn Stand Mixer to the 0 (Off) position and unplug. 2. Loosen attachment knob by turning it counterclockwise. 3. Flip up hinged hub cover. 4. Insert attachment shaft housing into attachment hub, making certain that attachment power shaft fits into square attachment hub socket. It may be necessary to rotate attachment back and forth. When attachment is in proper position, the pin on the attachment will fit into the notch on the hub rim. 5.
