KiCtchmmA#d* 42” (1067 m Built-h Refrigerator Model 4KSRF42DT i I IMPORTANT: Installer: Leave tnstallation lnstr~~ctionswith the Homeowner. Hommwr@r: Keep Installation I Instructions for future reference. Save Installation Instructions for local electrical inspector’s use. Part No. 1113438 * Registered Trademark of KitchenAid, Inc., U.S.A., KitchenAid Canada, Inc.
Before you start... Proper installation is your responsibility. Make sure you have everything necessary for correct installation. it is the responsibility of the installer to comply with the installation specifications provided. The built-in refrigerator weighs over 400 Ibs (181 kg). The floor must be sturdy enough to support this weight plus the additional weight of door panels, food and ice. Grounded electrical outlet is required. See Electrical requirements.
Dimensions for built-in area Electrical outlet should be centered wlthln shaded area. electrical 01 let location &ouhded (178 ml 356 mm) Width and depth of the built-in area are determined by the type of installation. The built-in refrigerator can be installed with the doors flush with the wall, with the doors protruding from the wall, or with side panels enclosing refrigerator. Select one method of installation and use the dimensions given for that method as shown.
Product dimensions Levelers extended l/8” (3 mm) below rollers *- f;i4, rece :sy)wldth 4- . .._.. . ..- i”‘(l9l-mm) grille l-118” (29 mm) max. wlth 8-112” (216 mm) grille T T 23.718” (696 mm) top of houslng to top of arllle Height dlmenslons when the mlnlmum extension of levelers [ll8” (3 mm) bdow rollers] is used to remove the welght from the rollers: 82-112” KZ.
Custom door panels, handle Inserts and top grille panels Panel routlng for door and top grille panels. Refrigerator door panel Door and top grille panels: Dimensions shown are with routed edges. Routing is required if panels are more than l/4” (6 mm) thick. 22-314” (578 mm) - 16-314" (425 mm) 114” 5/l 6” (8mynm) b + r. 26-114" (667 mm) 3” (76 mm) mln. t A lr--J A I 70.
+I-l/8” Side panel requirements I t -(lo67 (3 mm) tolerance mm)-b c 4 c + -II- S/32" (4mm) 23-118” (587 mm) depth protruding door lnrtalfatlon mm) + 1116" 23-716" (606 mm) depth flush door lnstallatlon 3-314" (95 mm) (2 il % ; ,I I J-l t - side trim spacers 1. Attach three spacers as shown to the top, middle and bottom of each side of the refrigerator. Spacers are required for ventilation. side panel support nailer .. when 25” (635 mm) depth is available.
Electrical requirements l l Electrlcal Shock Hazard Improper connectlon of the equlpment-groundlng conductor can result In a rlsk of electrical shock. Check wlth a quallfled electrictan or service technlclan If you are in doubt as to whether the appliance Is properly grounded. Do Not use an extenslon cord wlth thls appliance. Such use may result In a fire, electrlcal shock, or other personal Injury. A 120-volt, 60-Hz, AC only, 15-or 20ampere, fused, electrical supply is required.
Product support wood , block(a) A solid soffit or a wood block is required to prevent the refrigerator from tipping forward after it is installed. !/I Determine what height the refrigerator will be when it is installed to fit opening. Determine the height to the top of the cover at the final installed height you plan to use. l\\\\\lj/fl Block(s) ml’*t be lorig.enough to fully cover wldth of cover. -Important: El&k(s) &,t extend et least 2” over cover. . f. ..
Now start... Remove top grille assembly . package, literature package and parts bag taped to the refrfgerator door and save. /II Product Damage Do Not lower refrigerator against shipping base when removing the shipping base. Lowering the refrigerator against the shipping base could damage the components on the bottom of the refrigerator. Floor Damage Keep cardboard shipplng piece or plywood under refrlgerator untli it is installed in operatlng position. Failure to do so may cause damage to floor covering.
51 Move refrigerator close to final position. Remove cardboard or plywood from n under refrigerator. Plug electrical cord into the grounded outlet. Use the screw from the parts package to install the plug retainer. Move the refrigerator evenly and straight into the opening. Check that the water line will not be kinked. Check that slack in the electrical cord hangs freely behind refrigerator or is placed on top of refrigerator next to cover. 17 Remove tape from % rear . leveling rods.
ml If you wish to change the door handle insert, slide insert trim into handle. See Custom panel and insert dimensions for exact sizes to cut custom inserts. Insert end caps into each end of door handle. Replace refrigerator door handle. (Some end caps are attached with screws.) . to refrigerator. Check that the power switch is in the “ON” position. Attach top grille decorative panel assembly to the keyhole bracket on the frame and pull down to secure.
If built-in refrigerator does not operate... Check that the circuit breaker is not tripped or fuses blown. Check that power supply cord is plugged into xall receptacle. A more detailed troubleshooting checklist is provided in the Use and Care Guide. Part No. 1113438 0 1989 KitchenAid Canada, Inc. If you need assistance... How to arrange for service... When you call, you will need the built-in refrigerator model number and serial number.
