User Manual

KisanKraft
®
Rice Mill
KK-RM-6NF4X
: www.kisankraft.com
: [e-mail]
: +91.80. 6835 7800
Page 8 of 20
10. The operator shall not leave the post during the operating process
11. Cut off the power supply and clean the machine and site at the end of the work.
12. . The company will not be responsible for the personal injury and economic loss caused by
the installation and use of the machine are not in accordance with the requirements of the
operation manual and the safety precautions.
13. The user shall contact the manufacturer after the safety sign is worn or lost and make up
in time.
Overview
The machine has the characteristics of reasonable matching, beautiful shape, simple and
compact structure, convenient operation and maintenance, reliable performance, economic
benefits, etc., and it is suitable for urban and rural families, food, brewing, breeding and other
industries. This machine has the characteristics of good rice quality, high rice production rate,
low power consumption, bright rice and low rice temperature compared with the traditional iron
roller rice milling machine. At the same time, because the fine bran is collected by the bran
collector, the working environment is clean, and the dust concentration is low.
Operating environment and working conditions
Environmental conditions for use: normal temperature
Working conditions: the voltage must meet the normal use requirements of the matched motor.
The workplace shall be ventilated, dry, spacious, bright, and equipped with fire-fighting facilities.
Forbidden information of machine: this machine can only be used for rice processing. It is
forbidden to use it for processing any other materials.
Impact on environment and energy: This product will not cause environmental pollution and
energy waste when it is used correctly
KisanKraft
®
Rice Mill
KK-RM-6NF4X
: www.kisankraft.com
: [e-mail]
: +91.80. 6835 7800
Page 13 of 20
7. Before starting the machine, the collection bag shall be tied and turn off the feeding
outlet by feeding switch knob.
8. When all checks are completed, it can start the test operation after confirming that the
machine is in normal and ensure the human-machine safety, and check whether the
rotation direction of the main shaft is consistent with the mark of the main shaft. The
new machine must run for 5-10 minutes without any load, and it can work normally
only if there is no abnormality.
9. Slowly open the feeding inlet after the machine operates normally when using the rice
mill, adjust the flow of the rice mill to a certain position, and observe whether the rice
outlet meets the requirements of the finished rice. When the accuracy is low, the
feeding inlet or the pressure spring can be adjusted to control the size of the outlet to
make the rice accuracy meet the normal requirements. For example, if the opening of
the feeding inlet is too large or the opening of the outlet is too small, the rice breaking
rate is high. In serious cases, it will cause overload and crashing. If the opening of the
feeding inlet is too small or the opening of the outlet is too large, the rice output is
relatively rough.
10. The operator shall stand at the side of the feeding inlet, and the hands shall not enter
into the feeding inlet. It is forbidden to open the cover during operation.
11. When the feeding inlet is blocked, it is forbidden to feed by hands, hardwood bars,
iron bars and others forced. Stop the machine and cut off the power supply when
removing the blocking.
12. After the material at the outlet is discharged, it shall be operated without load for 1-2
minutes, and close the feeding inlet, stop the machine after the material is cleared in
the machine.
Common Faults and Troubleshooting
No.
Faults
Fault cause
Troubleshooting
1
Decline of
production
1. The screw propeller is
seriously worn
1. Replace the main axis
2. Rice roller is seriously worn
2. Replace the main axis
3. The feeding inlet is blocked
3. Clean the feeding inlet
2
Much broken
rice in the
finished
product
1. Rice roller has burr
1. repair the rice roller
2. Excessive pressure in rice
milling chamber
3. The inlet rice contains too
many impurities, poor quality or
too high or too low moisture
2. Adjusting the pressure spring
to reduce the pressure in the
rice milling chamber