KIP 800 | Color Series Hardware User Manual Version A.
Thank you for purchasing the KIP 800 Series. This Hardware Operation Guide contains functional and operational explanations for the KIP 800 Series. Please read this Hardware Operation Guide carefully before using the Printer. Please keep this Hardware Operation Guide for future reference. 1. When this product is installed in North America. This product complies with part 15 of the FCC Rules.
KIP 800 Series is an ENERGY STAR qualified multifunction device. The International ENERGY STAR ® Office Equipment Program is an international program that promotes energy saving through the penetration of energy efficient computers and other office equipment. The program backs the development and dissemination of products with functions that effectively reduce energy consumption. It is an open system in which business proprietors can participate voluntarily.
Safety Warning The following warnings are very important in order to safely use this product. These notes are important in preventing danger to the operator or operation of the printer. The following symbols are found throughout the USER’S Manual and have the following meaning: WARNING This WARNING mark means that there is a possibility of death or serious injury if you ignore or do not follow the said instruction.
WARNING Ground the product with a correct ground source or you may be electrically shocked. 1. The Power source should be as follows: 208 to 240V plus 6% or minus 10%, 50/60Hz, 16A or higher 2. Use a circuit with a dedicated breaker. 3. Install the product as close to the wall outlet as possible. 4. If you wish to move the printer, please contact your service personnel. 1. Do not remove the screw and do not open the cover if not instructed to do so in this User’s Manual.
CAUTION Do not install the printer in a humidified room or a dusty room. Also, do not install the printer on an unstable floor as injuries may occur. 1. Unplug the printer before you move it. The power cord may be damaged and it may result in a fire or electric shock. 2. If you do not use the printer for a long duration (holidays, company shutdown) turn off and unplug the printer from the outlet for safety. Do not pull the cord when you unplug the printer as you may damage the Power Cord.
POWER CORD INSTRUCTION The installation of (or exchange to) a power plug which fits in the wall outlet of the installation location shall be conducted in accordance with the following: WARNING Select a power plug which meets the following criteria; - The plug has a voltage and current rating appropriate for the product’s rating marked on its name plate. - The plug meets regulatory requirements for the area. - The plug is provided with a grounding pin or terminal.
Chapter 1 Introduction Page 1. 1 Installation Requirements 1- 2 1. 2 Originals Prohibited from Duplication 1- 3 1. 3 Features 1- 4 1. 4 Specifications 1. 4. 1 Printer Part 1. 4. 2 Scanner Part (KIP 860 only) 1- 5 1- 5 1- 7 1. 5 Appearance 1. 5. 1 Front view 1. 5. 2 Left side view 1. 5. 3 Right side view 1. 5. 4 Rear view 1- 8 1- 8 1- 9 1- 10 1- 11 1. 6 Specifications for the Printing Paper 1. 6. 1 Papers not available to use 1. 6. 2 Keeping the paper in the custody 1. 6.
1. 1 Installation Requirements The following conditions are required for installation of the equipment. 1. Power source should be rated as follows. 208V - 240V plus 6% or minus 10%, 50/60Hz, 16A or higher 2. The equipment must be on an exclusive circuit. 3. The outlet must be near the equipment and easily accessible. 1. Make sure to connect this equipment to a grounded outlet. 2. For PLUGGABLE EQUIPMENT, the socket-outlet shall be installed near the equipment and shall be easily accessible. 1.
1. 2 Originals Prohibited from Duplication It may be illegal to duplicate or copy certain types of originals and you may be punished by local or regional laws, if copies are made of these types of originals. Please be aware of your local or regional laws and which originals they forbid you to duplicate. Some Examples: [Originals prohibited from copying by the law(s)] 1. Do not copy Currency (Bill, Money, Bank Note, etc.
1. 3 Features (1) KIP 800 Series is an Electro Photographic full color LED printer/MFP. (2) Selection from 3 models are available according to the requirement. - KIP 870 : 4 rolls wide format color printer model - KIP 860 : 2 rolls wide format color printer MFP model - KIP 850 : 2 rolls wide format color printer model (3) Widths and lengths supported are; Max. width : 914mm (36”) Min. width : 279.4mm (11”) Max. length : 6,000mm (in case of A0/36) Min. length : 210mm (8.
1. 4 Specifications 1. 4. 1 Printer part Subject Model Type Printing method Color Photoconductor Print speed Exposure method Resolution Print width Print length Specification KIP 800 Series - KIP 870 : 4 rolls wide format color printer - KIP 860 : 2 rolls wide format color MFP - KIP 850 : 2 rolls wide format color printer Console type full color printer LED Array Electro Photography CMYK Organic Photoconductive Drum 80mm/sec. (3.9 A0/min, 7.5 A1/min.) : Color 100mm/sec. (10 D size/min.
Subject Dimensions Weight Media Environmental condition Storage condition of consumables Hardware option Specification KIP 870 : 1,500mm (W) x 1,080mm (D) x 1,220mm (H) KIP 860 : 1,500mm (W) x 1,080mm (D) x 1,155mm (H) KIP 850 : 1,500mm (W) x 1,080mm (D) x 1,015mm (H) NOTE : Touch panel and upper trays are not included. KIP 870 About 530kg (1168lb) KIP 860 About 510kg (1124lb) KIP 850 About 485kg (1069lb) Bond/Plain paper - 70 to 80 g/m2 (Monochrome : 100mm /sec.) - 70 to 90 g/m2 (Color : 80mm /sec.
1. 4. 2 Scanner part (KIP 860 only) Subject Scanning method Light source Scanning speed (600 dpi, normal quality) (max) Setting of original Starting point of scan Scan width Scan length Optical resolution Digital resolution Original transportation Transportable original thickness Specification Contact Image Sensor (CIS) (5 pieces of A4 sized CIS) LED (R/G/B) Monochrome : 65mm/s Grayscale : 65mm/s Color : 22mm/s NOTE : The actual speed may vary by the scan software. Face up Center Max: 914.
1. 5 Appearance 1. 5. 1 Front view 1 1 3 4 2 5 8 6 7 1 2 Name of part Print Tray Scanner Unit 3 Scan Abort Button 4 Start Button 5 User Interface 6 7 Bypass Feeder Roll Deck 8 Status Indicator Function These trays catch ejected prints. Read the original with this unit when you make scan or copy. (KIP 860 only) While scanning: emergency stop At Standby position: eject Starts scanning if the controlling software requires user intervention.
1. 5. 2 Left side view 1 5 2 3 4 1 2 3 4 5 6 Name of part Toner Cartridge Media Feeding Knob Unlock Lever (for the Feeder Unit) Left Side Cover Exhaust Fan Waste Toner Box 6 5 Function 4 Toner Cartridges (cyan, magenta, yellow and black) supplies the toner little by little. When the paper jam occurs, the media is fed by rotating this knob. When the paper jam occurs, the Feeder Unit is lowered by this lever to remove the jammed media. Open here to replace the Toner Cartridge.
1. 5. 3 Right side view 1 2 1 Name of part USB Port 2 Power Switch Function Your USB flash memory storage can be installed here. 5VDC max. Turns on/off the Printer.
1. 5. 4 Rear view 1 2 3 4 5 6 1 Name of part Fuser Knob 2 3 Upper Exit Unit Fuser Cover 4 5 6 Breaker Stacker Port Inlet Socket Function Rotate this knob when removing the misfed paper in the Fuser Unit. It ejects prints upward or backward. Prints come from the opening on this. Open the Fuser Cover when you remove the paper misfed inside the Fuser Unit. It is possible to shut off supplying the AC power. For a dedicated Auto Stacker for the Printer (DC24V 2A) Connect the Power Cord here.
1. 6 1. 6. 1 Specifications for the Printing Paper Papers not available to use Do not use the following kinds of printing paper. Doing so may damage the print engine.
Pre-printed Extremely slippery Extremely sticky Extremely thin and soft OHP Film CAUTION Do not use the paper with staple, or do not use such conductive paper as aluminium foil and carbon paper. The above may result in a danger of fire NOTE (1) Print image may become light if printed on a rough surface of the paper. (2) Print image may become defective if the print paper has an excess curl.
1. 6. 3 Treatment against environmental condition Take a necessary treatment according to the environmental condition as shown below. Humidity(%) Low Possible problem “Void of image”, “crease of paper” and other problems occurs when you print with plain paper and tracing paper. “Void of image” occurs when you print with tracing paper. 40% 70% “Void of image” occurs when you print with plain paper and tracing paper.
1. 7 Specifications for Scan Original (KIP 860 only) A scan original must satisfy the following specifications. Thickness Width Length 0.05mm to 1.60mm 210mm to 914.4mm 210mm to 6,000mm NOTE : 1. Image quality for an original with 0.25mm or thicker is guaranteed only in a standard size even the scanner physically accepts it. 2. Image quality for an original over 6,000mm in length is not guaranteed. 1. 7. 1 (1) (2) (3) (4) (5) Original Standards The width of original must range from 8.
1. 7. 3 “Do Not Scan” Originals It is impossible to use the following types of originals because they are likely to damage the scanner. Do not scan the following kinds of original, because you may damage the original or scanner itself! Sticked with paste Paste Torn Folded (Leading edge) So much curled (Diameter is smaller than 50mm.
Not square Wet image Wet Made of metal or fabric Metal Rough surface (Carbon paper for example) Fabric Rough surface Clipped or stapled Clipped 1-17 Stapled Chapter 1 Before Use
The following kinds of originals can be read with using a carrier sheet. However, the image quality and feed reliability are not guaranteed.
Chapter 2 Basic Operations Page 2. 1 Turning on the Printer 2- 2 2. 2 Turning off the Printer 2- 4 2. 3 Replacing the Roll Media 2- 6 2. 4 Placing Cut Sheet Media 2-13 2. 5 Replacing the Toner Cartridge 2-14 2. 6 Replacing the Waste Toner Box 2-17 2. 7 Copying (for KIP860) 2-21 2.
2. 1 Turning on the Printer 1. Plug the Printer to an exclusive wall outlet. WARNING Please confirm the outlet satisfies the following condition before plugging the Printer into. 208-240V (+6% to -10%), 16A, and 50/60Hz 2. Press “ | ” side of the Power Switch. Press this side 3. The status indicator on the upper right of the printer is blinking and the warming-up is started. NOTE The machine does not operate at all If the circuit breaker is turned off.
4. The Printer will get ready about 6 minutes after turning on. The Status Indicator stops blinking and lights green when ready. Make a copy or print from outer devices.
2. 2 Turning off the Printer 1. Press “ ” side of the Power Switch. Press this side 2. The Status Indicator light purple while the embedded controller unit is shutting down. It will turn off in few minutes. NOTE The controller unit starts shutdown process after turning off the Printer, and it will take about 1 minutes until complete shut down. Do not unplug the Printer from the outlet for about 1 minutes after turning off therefore.
3. If you completely shut the power supply due to a long vacation or the machine’s transport, turn off the circuit breaker and then remove the power cable from the machine.
2. 3 Replacing the Roll Media UI displays a sign of “Roll Replacement” when the used roll media gets empty. Follow the later procedure to load a new roll media. 1. Open the Roll Deck (1) that has empty roll media. With catching the Flanges (2) on both sides, lift and remove the core of roll (3). 2 2 1 3 2. Pull the green lever (4) on each Flange (2), which releases the core of roll (3). Remove both Flanges (2). 3 4 2 2 2 3.
4. Insert both Flanges (2) deep into the core of new roll media until they stop. 2 NOTE (1) Insert Flanges (2) deep enough into the core of roll media until their inside rims surely touch the side face of roll media with having no gap. Inside Rim Inside Rim OK NG Gap Correct: Fully inserted Incorrect: There is gap (2) Be careful not to be harmed by the saw-toothed edge (6) when handling the Flanges (2).
5. Turn down the lever (4) in either way until they completely stop, which lets the Flange to surely hold the roll media. 4 4 6. Fit both Flanges correctly into both Slide Guides (5) in the roll deck.
NOTE (1) Note the position of leading edge. It should be on the bottom side when directed to the media feeding path. Correct Incorrect to media feeding path to media feeding path Correct: Leading edge is on bottom side Incorrect: Leading edge is on top side (2) The outside rim (7) of the Flange must be aligned with the tip of black triangle (8) for correct gear engagement. If not, the Flange may come off from correct position and may result in incorrect media feeding.
7. Insert the leading edge into a slit under the Guide Plate (9) until it touches the feeding roller (10).
8. Rotate the small green roller (11) in the direction of arrow by hand for allowing the feeding roller to surely hold the leading edge. Front Deck (Roll 1 / 3) Rear Deck (Roll 2 / 4) 11 11 Roll 1 Roll 2 10 10 Roll 3 Roll 4 9. Push the Roll Deck (1) back in. 1 1 NOTE (1) Surely close the Roll Deck until it is locked. A paper jam may occur if not locked perfectly. (2) Be careful not to catch your finger in between Roll Deck drawers.
10. Define the media information (media type and width) with using the touch screen. Press [OK]. NOTE Incorrect settings lead to unwanted print results (fusing defect, improper image quality).
2. 4 Placing Cut Sheet Media 1. Open Manual Table (1). 1 2. There are several size markings on Manual Table which indicate possible feed positions. Place a cut sheet in a required size on the table between its concerning size markings then i nsert it into Manual Feeder. When the leading edge touches the feeding roller, the machine automatically carries and sets the sheet at the proper position.
2. 5 Replacing the Toner Cartridge UI Screen displays a sign of toner empty when the toner in the Toner Cartridge is empty. Follow the later procedure to replace the Toner Cartridge with a new one. 1. Open the Left Side Cover (1). 1 2. Rotate the Toner Cartridge (2) in the arrow direction until it stops. Pull and remove the empty Toner Cartridge. 2 2 NOTE The Toner Cartridge should be returned to your service technician or should be discarded according to your local regulations.
3. Prepare a new Toner Cartridge (3) of the same color and shake it enough to loosen the toner. 3 4. With catching the head part (black part), rotate the body (white part) of the Toner Cartridge in the direction of arrow for more than 3 revolutions. This will have a space in the toner supplying hole. NOTE Toner Supplying hole does not open enough if the body is not rotated enough, which causes the developer not supplied with enough toner. 5.
6. Rotate the Toner Cartridge (3) in the arrow direction until it stops. 3 NOTE Be sure that the tip of color sticker should not go further beyond LOCK position. OK NG 7. Close the Left Side Cover (1). When the Left Side Door is closed; ¾ ¾ The machine goes into “warm up” while processing toner supply. The machine gets “ready” when the toner refilling completes.
2. 6 Replacing the Waste Toner Box 1. Follow the figures in below to assemble a new Waste Toner Box. Sticker (Large) Sticker (Large) Sticker (Small) Stickers (Small) Reference A sheet of Sticker (Large) still remains after assembling the new Waste Toner Box. This is to be used to close the opening of the box when "waste toner full" occurs next time. Please keep this remaining Sticker (Large) at any place where you easily can find it.
2. Open the Left Side Cover (1). 1 3. Bring up the Waste Toner Box (2) a little and move it frontward to remove from the machine. 2 4. Apply the Sticker (3) to close the opening of the Waste Toner, which is included in the WASTE TONER BOX KIT. 3 WARNING Do not discard it as a flammable. Toner will explode if thrown into the fire. Please ask the seller for the way of dispose. NOTE (1) Do not handle the Waste Toner Box roughly. Otherwise the toner will come out from its open hole.
5. Set the new Waste Toner Box (4) back in the original position. See the following NOTE. 4 NOTE (1) Place the bottom corner of the box at the inside of the positioning step (5). 4 5 (2) Make sure the clear film windows (6) is not dirty.
6. Close the Left Side Cover (1).
2. 7 Copying (for KIP860) Please refer to the detailed procedure for making a copy, which is included in "GUIDES" in UI Home screen as well. 1. Press [COPY] in UI Home screen. The UI screen may vary depending on your system configuration. (Shown with available options) 2. There are several size markings on Original Table which indicate possible feed positions. Line up Original Guides (1) with the proper markings according to the original width. 1 1 3.
4. The KIP 860 will start the copy process. Reference Pressing START button may be required to start the scan according to the scanner’s controller software. For further details of “Auto Start”, see the software’s document. Start Button NOTE The scanner unit does not accept originals automatically during Sleep Mode. Tap on the UI screen and then insert an original.
The KIP 800 Series has 2 print delivery system, the print tray / rear stacking equipment. NOTE For the front stacking, gently lift up the prints on the print tray to the arrow direction to avoid rubbing the print surface. A large number of prints should be removed in several sheets. OK NG Correct: Gently lift up and remove Wrong: Do not pull downward For the front stacking, the printer will inform you of “Upper Bin Full” on exceeding capacity of stacking.
2. 8 Stop of Scan or Copy (for KIP860) 1. If necessary, press the Scan Abort Button on the Scanner Unit to immediately stop the original while making a copy or scan. Scan Abort Button Pressing the button stops the current reading a document immediately. The current printing is stopped as well and is ejected. NOTE Do not pull back or hold down the original on Original Table as an attempt to stop feeding it through Scanner Unit.
Chapter 3 Error Correction 3. 1 Mis-feed Error 3. 1. 1 Roll Deck Section Jam (Deck 1, 2, 3, 4 Mis-feed) 3. 1. 2 Manual Feeder Section Jam (Feeder part Mis-feed (1)) 3. 1. 3 Media Feed Section Jam (Registration Mis-feed, Feeder part Mis-feed (1), (2), (3)) 3. 1. 4 Exit Section Jam 1 (Exit Mis-feed, Separation Mis-feed (1)) 3. 1. 5 Exit Section Jam 2 (Exit Top Mis-feed) 3. 1. 6 Scanner section Jam (Scanner document jam) (for KIP860) Page 3- 2 3- 3 3- 5 3- 6 3- 8 3-11 3-12 3. 2 Door Open 3. 2.
3. 1 Mis-feed Error "XXXX Mis-feed" is displayed in the UI screen when the media is jammed. The jammed locat ion when displaying "Mis-feed" is shown below. Scanner Section Exit Section 2 Media Feed Section Manual Feeder Section Roll Deck Section Exit Section 1 NOTE (1) Be careful not to get paper cuts on your hand. (2) Gently remove a jammed paper. When it does not reach Fuser Unit, toner on it may spill off. If toner gets into eyes or your mouth, immediately rinse them with water and contact a doctor.
3. 1. 1 Roll Deck Section Jam (Deck 1, 2, 3, 4 Mis-feed ) Roll Deck Section Deck 1 Mis-feed Roll Deck Section Deck 1 Mis-feed Deck 3 Mis-feed (for KIP870) Roll Deck Section Deck 2 Mis-feed Deck 4 Mis-feed (for KIP870) Clear the Paper Mis-feed using the following procedure: 1. Open the Roll Deck (1) in issue. And then rewind the roll onto the media core. 1 2. If the leading edge of the media is torn or folded, cut it off.
3. Set the roll media correctly. Front Deck (Roll 1 / 3) Rear Deck (Roll 2 / 4) NOTE The outside rim of Flange should meet the black triangle marked on Slide Guide. Otherwise the roll media may fall in Roll Deck or result in an incorrect media feeding. OK NG Out of position Correct Wrong 4. Close the Roll Deck.
3. 1. 2 Manual Feeder Section Jam (Feeder part Mis-feed (1)) Manual Feeder Section Feeder part Mis-feed (1) 1. Pull out the mis-feed cut sheet from the Manual Feeder. NOTE The mis-feed cut sheet should be replaced with a new one if its leading edge has a torn or fold. Or it should be used upside down to keep the damaged edge from been inserted. An extremely creased cut sheet may cause mis-feed again.
3. 1. 3 Media Feed Section Jam (Registration Mis-feed, Feeder part Mis-feed (1), (2), (3)) Media Feed Section Feeder part Mis-feed (2) Media Feed Section Feeder part Mis-feed (3) Media Feed Section Feeder part Mis-feed (1) Media Feed Section Resistration Mis-feed 1. Open the Left Side Cover (1). 1 2. Turn the Lever (2) to the arrow direction.
3. Remove the jammed media. 4. In case that the media is pinched by the roller and cannot be removed, rotate the Paper Feeding Knob (3) to feed the media to the Feeder Unit, and then remove it.
3. 1. 4 Exit Section Jam 1 (Exit Mis-feed, Separation Mis-feed (1)) Exit Section 1 Exit Mis-feed Exit Section 1 Separation Mis-feed (1) 1. Open the Fuser Cover (1).
2. Holding the knob (2) on both sides, lift up the Separation Finger Assy (3) until the hook (4) catches the shaft (5).
3. Rotate the Fuser Knob (6) to the arrow direction to feed the media to the exit direction, and then remove it. 6 WARNING There are extremely hot parts inside the Fuser Unit. Do not touch any parts in the Fuser Unit, or you will be burnt. Also the mis-fed media can be very hot. Be careful not to get burnt when you remove it. 4. Pull up the knob (7) on the both sides to put back the Separation Finger Assy to the original position.
3. 1. 5 Exit Section Jam 2 (Exit Top Mis-feed) Exit Section 2 Exit Top Mis-feed 1. Remove the Exit Tray 2 (1). 1 2. Open the Upper Exit Unit (2) and then remove mis-feed paper (3).
3. 1. 6 Scanner Section Jam (Scanner document jam) (for KIP860) If an original is mis-fed while scanning, the UI screen shows “Scanner document jam”. Follow the instruction below to remove the mis-fed original. 1. Lift up both sides (1) of the Scanner Unit 1 2. Remove a mis-feed original. 3. Gently press the Scanner Unit down and firmly close it. NOTE Press down the Scanner Unit on both sides to close it. Do not close it by pressing only one side down.
3. 2 Door Open "Door Open" is displayed in the UI screen when the door in each unit is opened. 3. 2. 1 Roll Deck (Deck 1 Open, Deck 2 Open) Close the Roll Deck securely to clear "Deck 1 Open" or “Deck 2 Open”. Roll Deck 3. 2. 2 Left Side Cover (Left Side Cover Open) Close the Left Side Cover securely to clear "Left Side Cover Open".
3. 2. 3 Fuser Cover (Fuser Cover Open) Close the Fuser Cover securely to clear "Fuser Cover Open". Fuser Cover 3. 2. 4 Upper Exit Unit (Paper Exit Door Open) Close the Upper Exit Unit securely to clear "Paper Exit Door Open".
3. 2. 5 Scanner Unit (Scanner feeder open) The UI screen shows “Scanner feeder open” if the Scanner Unit is open. (not closed properly) Close the Scanner Unit securely to clear " Scanner feeder open ".
3. 3 3. 3. 1 Other Operator Call Roll Replacement When the printer is running out of a loaded roll media, the UI Screen will display “Out of Paper” sign. If there is no suitable roll media required for the current print job, the UI Screen will display “Out of Paper” sign as well. Please load the required roll media to any Roll Deck. For the roll replacement procedure, see [2.3 Replacing the Roll Media]. 3. 3.
3. 3. 3 Waste Cartridge full When the Waste Toner Box is full, the UI screen shows “Waste Cartridge full.” The printer does not restart operation until the Waste Toner Box is properly replaced. For replacement procedure, see [2.6 Replacing the Waste Toner Box]. Waste Toner Box 3. 3. 4 Web Cleaner Empty Web Cleaner is a component to clean Fuser Unit. When the remaining Web Cleaner is low, the UI screen displays “Web Near End”.
3. 4 Service Call Error If an error with significant effect on the printer occurs, the printer stops the operation and indicates a related Customer Engineer Call Error Code (or description, and its equivalent internal code) on the UI screen. Call the service staff immediately as these problems can be fixed by a well trained technician only. Before calling the service staff, try to turn on/off the Printer.
Chapter 4 Maintenance 4. 1 Scanner Unit (KIP 860 only) 4. 1. 1 Scan Glass, Feed Roller, Guide Plate 4. 1. 2 Sensor 4.
4. 1 Scanner Unit (KIP860 only) 4. 1. 1 Scan Glass, Feed Roller, Guide Plate It is recommended to clean each Scan Glass, Feeding Rollers and Guide Plates as the scan/copy image may become defective if these parts are dirty. NOTE For ease of visual check, this document shows the Upper Unit fully open (not actual wide). 1. Turn off the Printer. 2. Lift up both sides (1) of the Scanner Unit.
3. Gently wipe the Scan Glass (2) and Feed Rollers (white) (3) with a soft cloth. Equal mixture of water and neutral detergent can be used. 2 3 NOTE Do not use organic solvent, glass cleaner and anti-static spray for the cleaning. 4. Wipe the Feed Rollers (rubber) (4) with a dry cloth. 4 4 4 4 5. Wipe dry the Feeding Rollers.
6. Wipe the Upper Guide Plate (5) and the Lower Guide Plate (6) with a dry cloth. 5 5 6 7. Gently press Scanner Unit down and firmly close it. NOTE Press down Scanner Unit on both side to close it. Do not close it by pressing only one side down.
4. 1. 2 Sensor If Sensors are dirty, the original may be detected incorrectly. Perform cleaning or as needed. NOTE For ease of visual check, this document shows the Upper Unit fully open (not actual wide). 1. Turn off the Printer. 2. Lift up both sides (1) of the Scanner Unit.
3. Gently wipe Sensors (2) with a dry cotton bud. 2 2 2 2 2 2 2 NOTE Do not use water, organic solvent, glass cleaner or antistatic spray for cleaning. 4. Gently press Scanner Unit down and firmly close it. NOTE Press down Scanner Unit on both side to close it. Do not close it by pressing only one side down.
4. 2 Touch Screen 1. Wipe the Touch Screen with a dry cloth. NOTE Do not use water, alcohol, organic solvent and glass cleaner for the cleaning.
