User Manual

TM
Grain CartM0238-01
Rev. 4/13 i
Table of Contents
OVERVIEW
To the Owner ....................................1-1
Warranty ........................................1-2
General Information ...............................1-2
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2
Specifications ....................................1-3
General Safety Rules ..............................1-7
Safety Precautions ................................1-7
Safety Signs And Decals ...........................1-8
Safety Instructions, Signs, and Decals . . . . . . . . . . . . . . . . .1-8
OPERATION
Machine Preparation ..............................2-1
Tractor Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1
Tractor Preparation and Hookup. . . . . . . . . . . . . . . . . . . . . .2-1
Joystick Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-4
Cart Operation ...................................2-4
PTO Torque Limiting/Overrunning Clutch Protection ......2-6
Belt Engagement Indicator . . . . . . . . . . . . . . . . . . . . . . . . . .2-6
Hydraulic Flow Gate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-6
Auger Inspection Cover ............................2-7
Grain Tank Clean Out Sweep ........................2-8
Vertical Auger Work Light . . . . . . . . . . . . . . . . . . . . . . . . . . .2-9
Cameras ........................................2-9
Manual and Electric Roll Tarp .......................2-10
Roll Tarp Remote Control Troubleshooting . . . . . . . . . . . . .2-13
Electronic Scale - GT 400. . . . . . . . . . . . . . . . . . . . . . . . . .2-14
Electronic Scale - GT 460. . . . . . . . . . . . . . . . . . . . . . . . . .2-15
Electronic Scale - GT 460 AutoLog ..................2-16
Electronic Scale Printing Options . . . . . . . . . . . . . . . . . . . .2-17
Electronic Scale Troubleshooting ....................2-20
Electronic Scale Troubleshooting ....................2-21
Data Downloader Troubleshooting ...................2-22
LUBRICATION AND MAINTENANCE
Drive Belts and Pulleys. . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2
Driveline Inspection ..............................3-18
Electronic Scale .................................3-33
Gearbox .......................................3-21
Gearbox Oil Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2
Grease Fittings ..................................3-3
Horizontal Auger Bearings ..........................3-1
Horizontal Auger Replacement. . . . . . . . . . . . . . . . . . . . . .3-21
Hydraulic Control Schematic - Manual . . . . . . . . . . . . . . . .3-30
Hydraulic Control Schematic - Remote ...............3-31
Joystick Electrical Schematic .......................3-32
Lower Vertical Auger Replacement ..................3-20
Mounting Bolts and Hardware .......................3-9
Preparation for Storage ...........................3-29
PTO Shaft Coupling ...............................3-2
Row Crop Inside Tire Repair or Removal .............3-24
Splines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1
Tire Servicing ...................................3-11
Torque Values Chart - Plated Hardware ................3-9
Track Alignment .................................3-23
Track Endwheel and Midwheel Bearings ...............3-1
Track Endwheel/Midwheel Bearing Replacement .......3-26
Track Tension ...................................3-22
Upper Vertical Auger Replacement ..................3-19
V-Belt Replacement ..............................3-16
V-Belt Tension Adjustment and Alignment . . . . . . . . . . . . .3-12
Vertical Auger Counter Balance Valves ...............3-10
Wheel Bearing Replacement .......................3-28
Wheel Bearings ..................................3-1
Wheel Nuts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-11
Wiring Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-33