Owner manual

ManualsBrandsKinze ManualsGardening equipment3600 Lift and Rotate Planter (70 CM) Rev. 5/14

M0249-01Model 3600

Rev. 5/14

TMTM

Table of Contents

LUBRICATION AND MAINTENANCE

Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

Lubrication Symbols .............................6-1

Sealed Bearings ................................6-1

Wrap Spring Wrench Assembly . . . . . . . . . . . . . . . . . . . . . 6-1

Drive Chains ...................................6-2

Bushings ......................................6-3

Center Post ....................................6-5

U-Joint Slides. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5

Wheel Bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6

Grease Fittings .................................6-6

Mounting Bolts and Hardware .....................6-10

Tire Servicing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11

Finger Pickup Seed Meter Inspection/Adjustment. . . . . . 6-12

Cleaning Finger Pickup Seed Meter For Storage ......6-13

Brush-Type Seed Meter Maintenance ...............6-14

Cleaning Brush-Type Seed Meter For Storage ........6-15

Vacuum Manifold Maintenance ....................6-15

EdgeVac Seed Meter Maintenance . . . . . . . . . . . . . . . . . 6-16

EdgeVac Seed Meter Cleanout ....................6-16

Chain Tension Adjustment . . . . . . . . . . . . . . . . . . . . . . . . 6-17

Drag Closing Attachment ........................6-17

Gauge Wheel Adjustment ........................6-17

Gauge Wheel Arm Bushing/Seal Replacement . . . . . . . . 6-18

Gauge Wheel Arm Pivot Spindle Replacement . . . . . . . . 6-18

15" Seed Opener Disc Blade/Bearing Assembly .......6-19

Seed Tube Guard/Inner Scraper ...................6-20

Frame Mounted Coulter .........................6-20

Residue Wheels (For Use With Frame Mounted Coulter)

. . . . . 6-20

Row Unit Mounted Disc Furrower ..................6-21

Row Unit Mounted Bed Leveler . . . . . . . . . . . . . . . . . . . . 6-21

Row Unit Mounted No Till Coulter ..................6-21

Coulter Mounted Residue Wheels . . . . . . . . . . . . . . . . . . 6-22

Row Unit Mounted Residue Wheel .................6-22

Granular Chemical Attachment ....................6-22

Spring Tooth Incorporator ........................6-22

Single and Two-Speed Point Row Clutch Maintenance

. . . . . 6-23

Check Valve (Lift System) ........................6-25

Check Valve (Vacuum Fan) .......................6-25

Flow Control Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-25

Pressure Relief Valve. . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-25

Pressure Reducing Relief Valve. . . . . . . . . . . . . . . . . . . . 6-25

Relief Valve Cartridge ...........................6-25

Solenoid Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-25

Row Marker Bearing Lubrication or Replacement . . . . . . 6-26

Row Marker Transport Stand Adjustment ............6-27

Wheel Bearing Repack or Replacement .............6-27

Wear Pad Field Replacement/Adjustment . . . . . . . . . . . . 6-28

Preparation for Storage ..........................6-31

Electrical Wiring Diagram for Light Package ..........6-32

Electrical Control Console Schematic ...............6-33

Electrical Wiring Harness Schematic (On Tractor). . . . . . 6-34

Electrical Wiring Harness Schematic (On Planter) .....6-35

Valve Block - Located on Hitch ....................6-36

Valve Block - Located on Rear Center Frame .........6-37

Electrical Control Console Schematic

(With Optional Two-Speed Point Row Clutches)

and Wiring Harness at Two-Speed Point Row

Clutch Solenoids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-38

Hydraulic System Schematic . . . . . . . . . . . . . . . . . . . . . . 6-39

Hydraulic Schematic - Vacuum Fan Motor System .....6-42

Wing Down Pressure Schematic

(Weight Transfer Mechanism) ...................6-43