Operation Manual Mega Double & Single Part No.
Mega Double System 2 CFX-9602 8ft Mega Double Fixture CFX-7202 6ft Mega Double Fixture MTP-KM Kino 81 “Slide-On” Mount w/ Junior Pin (28mm) X09-25M Mega Double Extension, 25ft BAL-215-M120 Mega Double Ballast, 120VAC BAL-215-M230 Mega Double Ballast, 230VAC
Mega Single System CFX-9601 8ft Mega Single Fixture CFX-7201 6ft Mega Single Fixture MTP-KM Kino 81 “Slide-On” Mount w/ Junior Pin (28mm) X07-25M Mega Single Extension, 25ft BAL-105-M120 Mega Single Ballast, 120VAC BAL-115-M230 Mega Single Ballast, 230VAC Each System consists of: 1 Mega Fixture 1 Mounting Plate 1 Extension Cable 1 Electronic Ballast True Match® Lamps 722-K32-S 722-K55-S 6ft Kino KF32 6ft Kino KF55 962-K32-S 962-K55-S 8ft Kino KF32 8ft Kino KF55 3
Fixture Assembly (x2) The Mega Double and Single fixtures are comprised of two removable Louvers, a Reflector and a Lamp Harness. The Louvers and Reflector are held in place with Velcro fasteners. The Lamp Harness is secured by means of a ¼ turn fastener and two clips. Note: The 8ft fixtures include two 4ft louvers; the 6ft fixtures include two 3ft louvers. To Release the Lamp Harness Remove the harness from 2 clips located under the reflector. Rotate the ¼ turn fastener clockwise to release harness.
Inserting Lamps Locking Lamp Connector: Depress both tabs on lamp connector and apply to lamp pins. Match the Harness color-codes at each end of the lamp. Push lamps into the fixture’s Lamp Holder Clips. Note: Mega 4Bank fixture is shown for example purposes only. Gelling the Fixture Restricting the airflow around the lamps can cause the lamps to operate hotter. This increased heat will raise the lamp’s color temperature and green spike.
Mounting the Fixture Align the four shoulder rivets on the mounting plate (MTP-KM) to the holes in the mating plate and slide down. The locking pin will snap into place when the plate is properly seated. The Silver Rings provide attachment points for a safety chain. To remove the plate, pull up on the locking pin and reverse the mounting procedure. A 180° turn loosens the orientation of the mount. A right turn tightens the mount.
Other Fixture Mounting Options The grommet holes along the edge of the fixture are designed to allow the fixture to be screwed onto set walls. Extension Cable To insert the cable, position the logo up to align the key ways on the extension cable with the circular receptacle on the ballast. Rotate the locking ring until it clicks into the lock position. Lamps can operate as far as 75 feet from the ballast.
Ballast Operation WARNING! 1) ALWAYS TURN OFF THE BALLAST BEFORE connecting or disconnecting Lamps, Harnesses or Extension Cables. 2) Use only with Sine wave inverters. Do not operate on SCR dimmers. 3) If powering the ballasts through a Dimmer Pack, set the Dimmer to Non-Dim mode. The 120VAC Ballast requires 110 to 130 Volts AC 50/60 Hertz on an earth grounded circuit; the 230VAC Ballast requires 220 to 240 Volts AC on an earth grounded circuit.
Mega Double Control Panel A B C D A) Circular Output Connector: Provides electrical power to the lamp head with the use of an extension cable. B) Fuse: Provides circuit protection. Note: If Fuse is “blown” or “open”, replace with same type of fuse rating as marked. C) Manual Switches: Turns lamps on and off manually. D) HO/STD: Set to HO for High Output and Std for Standard light output. (Note: The Mega Double ballast is shown for example purposes.
Manual Operation The Ballast operates remote from the fixture. Connect the Extension cable to the Ballast and the Lamp Harness. After the lamps are properly installed, the Ballast can be turned on. Each switch controls one lamp. The color bands on the lamp harness correspond to the switches as illustrated. Red Yellow Lamp Select Feature The Mega Ballasts have an HO/Std switch. Set the selector switch to HO for High Output and Std for Standard light output.
System Components CFX-9602 CFX-9601 CFX-7202 CFX-7201 8ft Mega Double Fixture 8ft Mega Single Fixture 6ft Mega Double Fixture 6ft Mega Single Fixture MTP-KM Kino 81 “Slide-On” Mount w/ Junior Pin (28mm) X09-25M X07-25M Mega Double Extension, 25ft Mega Single Extension, 25ft BAL-215-M120 Mega Double Ballast, 120VAC BAL-215-M230 Mega Double Ballast, 230VAC BAL-105-M120 Mega Single Ballast, 120VAC BAL-115-M230 Mega Single Ballast, 230VAC True Match® Lamps 722-K32-S 722-K55-S 6ft Kino KF32 6ft Kino
Accessories and Parts FIX-9602 FIX-9601 8ft Mega Double Fixture Shell 8ft Mega Single Fixture Shell FIX-7202 FIX-7201 6ft Mega Double Fixture Shell 6ft Mega Single Fixture Shell HAR-9602 HAR-9601 8ft Mega Double Fixture Harness 8ft Mega Single Fixture Harness HAR-7202 HAR-7201 6ft Mega Double Fixture Harness 6ft Mega Single Fixture Harness LVR-4802-B LVR-4801-B LVR-3602-B LVR-3601-B 4ft Double Louver, Black 4ft Single Louver, Black 3ft Double Louver, Black 3ft Single Louver, Black * 8ft Fixtures r
Expendables EXP-LHC-T12 EXP-M&T Lamp Holder Clips, T12 (24pk) Adhesive Mounts & Releasable Ties (25pk) PRT-HLC Kino Locking Lamp Connector (1pk) PRT-HLC/50PK Kino Locking Lamp Connector (50pk) See our website at www.kinoflo.com for more repair parts. Cases KAS-96 KAS-96L KAS-KFC Part Number Description Dimensions Weight (Empty) Holds INS-L4 4-Lamp Foam Pad 24 x 9 x 1” (61 x 23 x 2.5cm) N/A Fits KAS-48, 72, 96 INS-L6 6-Lamp Foam Pad 24 x 13 x 1” (61 x 33 x 2.
Fixture Specifications Kino Flo Mega Double Fixture Dimensions Fixture Style Length Width Depth Barndoor Width Weight w/ Lamps 8ft Mega Double 97” 7.5” 3.5” 3.5” 10 lbs 6ft Mega Double 73.5” 7.5” 3.5” 3.5” 9.2 lbs Kino Flo Mega Single Fixture Dimensions Fixture Style Length Width Depth Barndoor Width Weight w/ Lamps 8ft Mega Single 97” 4.5” 3.5” 3.5” 6.8 lbs 6ft Mega Single 73.5” 4.5” 3.5” 3.5” 6.
Ballast Specifications BAL-215-M120 Mega Double Input Voltage: 120VAC 50/60Hz Output Frequency: 25kHz Amperage: F120/3.7A, F100/3.1A Lamp Switching: 1~2 Output Switching: HO/Std Ballast Size: 9.5 x 9 x 3” (24 x 23 x 7.6cm) Weight: 3.5 lb (1.6kg) BAL-215-M230 Mega Double Ballast, 230VAC Input Voltage: 230VAC 50/60Hz Output Frequency: 25kHz Amperage: F120/2.2A, F100/1.7A Lamp Switching: 1~2 Output Switching: HO/Std Ballast Size: 9.5 x 9 x 3” (24 x 23 x 7.6cm) Weight: 4.2 lb (1.
For latest Warranty information and Certifications, see Kino Flo website at www.kinoflo.com. Environmental: Disposal of Old Electrical & Electronic Equipment. This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. This product is made of recyclable materials and should be disposed of in accordance with governmental regulations. Kino Flo, Inc. 2840 N. Hollywood Way, Burbank, CA 91505, USA Tel: 818 767-6528 website: www.kinoflo.
