User's Manual

Long Range LoRa™ TechnologyTransceiver Module

• Approved Antennas
Modular certification of the KT1276 module was performed with
82mm.
Referto"RegulatoryApproval" for specific regulatory requirements bycountry.
6.0
Regulatory Approval
The KT1276modulehasreceivedFederalCommunications
15 Subpart C “IntentionalRadiators” modular
Part15.212ModularTransmitterapproval.
Modularapproval allows the end user to integrate the KT1276module into a finished product
without obtainingsubsequentandseparateFCCapprovalsforintentionalradiation,
to the module circuitry.
Changes or modifications could void the user'sauthority to operate the equipment. The end user
mustcomply with all of the instructions provided by theGrantee, which indicate installation
and/or operatingconditions
necessary for compliance.
The finished product is required to comply with allapplicable FCC equipment authorizations
regulations,requirements and equipment functions not associatedwith the transmitter module
portion. For example,compliance must be demonst
components within the host product;to requirements for unintentional radiators (Part 15Subpart
B “Unintentional Radiators”), such as digitaldevices, computer peripherals, radio receivers,
etc.;and to additional aut
horization requirements for thenon
transmitter module(i.e., Verification, or Declaration of Conformity) (e.g.,transmitter modules may
also contain digital logicfunctions) as appropriate.
•
LABELING AND USERINFORMATION REQUIREMENT
The KT1276 module has been labeled with its ownFCC ID number, and if the FCC ID is not visible
whenthe module is installed inside another device, then theoutside of the finished product into
which the module isinstalled must also display a label referrin
exterior label can use wordingas follows:
Contains Transmitter Module FCC ID:
or
Contains FCC ID: 2AFK9KT1276
This device complies with Part 15 of the FCC Rules.Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference,and (2) this device must accept any
interferencereceived, including interference that may causeundesired operation.
A user's manual for the finished product should includethe following statement:
This equi
pment has been tested and found to complywith the limits for a Class B digital device,
pursuant topart 15 of the FCC Rules. These limits are designedto provide reasonable protection
against harmfulinterference in a resid
radiate radio fre
quency energy, and if not installed and used inaccordance with the instructions,
may cause harmfulinterference to radio communications. However,there is no guarantee that
Long Range LoRa™ TechnologyTransceiver Module
KT1276
2017 KingTing Tech. Corporation
Modular certification of the KT1276 module was performed with
wire antenna, the
Referto"RegulatoryApproval" for specific regulatory requirements bycountry.
Regulatory Approval
The KT1276modulehasreceivedFederalCommunications
Commission
(FCC)CFR47Telecommunications, Part
15 Subpart C “IntentionalRadiators” modular
approval in accordance with
Part15.212ModularTransmitterapproval.
Modularapproval allows the end user to integrate the KT1276module into a finished product
without obtainingsubsequentandseparateFCCapprovalsforintentionalradiation,
provided
nochangesormodif
ications are made
Changes or modifications could void the user'sauthority to operate the equipment. The end user
mustcomply with all of the instructions provided by theGrantee, which indicate installation
necessary for compliance.
The finished product is required to comply with allapplicable FCC equipment authorizations
regulations,requirements and equipment functions not associatedwith the transmitter module
portion. For example,compliance must be demonst
rated to regulations forother transmitter
components within the host product;to requirements for unintentional radiators (Part 15Subpart
B “Unintentional Radiators”), such as digitaldevices, computer peripherals, radio receivers,
horization requirements for thenon
-
transmitter functions on the
transmitter module(i.e., Verification, or Declaration of Conformity) (e.g.,transmitter modules may
also contain digital logicfunctions) as appropriate.
LABELING AND USERINFORMATION REQUIREMENT
S
The KT1276 module has been labeled with its ownFCC ID number, and if the FCC ID is not visible
whenthe module is installed inside another device, then theoutside of the finished product into
which the module isinstalled must also display a label referrin
g to theenclosed module. This
exterior label can use wordingas follows:
Contains Transmitter Module FCC ID:
2AFK9KT1276
This device complies with Part 15 of the FCC Rules.Operation is subject to the following two
(1) this device may not cause harmful interference,and (2) this device must accept any
interferencereceived, including interference that may causeundesired operation.
A user's manual for the finished product should includethe following statement:
pment has been tested and found to complywith the limits for a Class B digital device,
pursuant topart 15 of the FCC Rules. These limits are designedto provide reasonable protection
against harmfulinterference in a resid
ential installation. This equipment generates
uses and can
quency energy, and if not installed and used inaccordance with the instructions,
may cause harmfulinterference to radio communications. However,there is no guarantee that
KT1276
wire antenna, the
length is
(FCC)CFR47Telecommunications, Part
approval in accordance with
Modularapproval allows the end user to integrate the KT1276module into a finished product
ications are made
Changes or modifications could void the user'sauthority to operate the equipment. The end user
mustcomply with all of the instructions provided by theGrantee, which indicate installation
The finished product is required to comply with allapplicable FCC equipment authorizations
regulations,requirements and equipment functions not associatedwith the transmitter module
rated to regulations forother transmitter
components within the host product;to requirements for unintentional radiators (Part 15Subpart
B “Unintentional Radiators”), such as digitaldevices, computer peripherals, radio receivers,
transmitter functions on the
transmitter module(i.e., Verification, or Declaration of Conformity) (e.g.,transmitter modules may
The KT1276 module has been labeled with its ownFCC ID number, and if the FCC ID is not visible
whenthe module is installed inside another device, then theoutside of the finished product into
g to theenclosed module. This
This device complies with Part 15 of the FCC Rules.Operation is subject to the following two
(1) this device may not cause harmful interference,and (2) this device must accept any
pment has been tested and found to complywith the limits for a Class B digital device,
pursuant topart 15 of the FCC Rules. These limits are designedto provide reasonable protection
uses and can
quency energy, and if not installed and used inaccordance with the instructions,
may cause harmfulinterference to radio communications. However,there is no guarantee that