User's Manual

1. Keep this product and its charging cable away from excessive heat.
2. Do not operate this device with a damaged cable or after it has
malfunctioned or has been damaged in any manner.
3. Do not disassemble your device.
In order to pair your Bluetooth audio device to your Bluetooth Speaker for
the first time, follow the steps below:
1). Make sure your Bluetooth audio source is held within three meters of
your speaker.
2). Press and hold the “ ” switch on your speaker to power on
The LED light will blink blue to indicate that you have entered pairing
status.
3). Go to the Bluetooth Manager of your Bluetooth audio source. Please
refer to the User’s Manual of your Bluetooth audio source for more
information.
4). Search Bluetooth devices and select “B18P”.
5). Once paired, the blue LED light will be solid and you can use your
speaker to listen to audio from you Bluetooth sound source
.
NOTE：Press the twice to disconnect the Bluetooth
Waterproof Wireless Speaker
User’s Manual
4. Only use your device on a flat, stable surface.
Charging your Speaker
A Quick Look at Your Device
Understanding the LED Status Lights
Aux-ln Mode
1. Connect one end of the included USB Charging Cable to the
Charging Port on your speaker. Then plug the other end of the USB
Charging Cable into a suitable USB port on your computer to recharge
your speaker’s internal rechargeable battery.
B18P
Introduction:
You can use this item with tablet,notebook and many types of smartphone
to stream music,and enjoy handsfree calling.In order to get
results when using the device,please read this manual first before using.
Features
Specification
Package Contents
Important Safety Precautions
-Clear sound music with colorful light show
-Volume and song control directly on unit
-Stunning sound clarity
-Ultra portable design
-Great for parties, indoor and outdoor
-Allow you to use hands free function
Loudspeaker: 4Ω 5W
Built-in Battery :Li-ion 1000mAh
Dimensions: 111mm(L)*99mm(W)*54mm(H)
SNR:≥8 2dB
Wireless Working Frequency: 2.402-2.480 GHZ
Wireless Transmission Distance: up to 10 m
Charging Time: 3-4 hours
Weight: 220 g
Troubleshooting
Problem
Solution
The speaker doesn’t connect
Speaker needs to be connected/re-paired to
device
to device
A tone is heard every few
seconds
Speaker needs to be charged
Avoid operating the Bluetooth speaker in areas
of strong electromagnetic interference,such as
near induction cookers,large power fans,motors
etc.
Move the speaker closer to Bluetooth
device.Fully charge the speaker and try again.
Bluetooth connection distance
cannot reach to 32ft.
The speaker will not power on
Speaker needs to be charged
The speaker doesn’t control
Speaker needs to be in Bluetooth mode for
full control
trac
k(
s
)/
vo
l
ume
The speaker distorts at high
The devices’ volume needs to be lowered
volume
Speaker Dimension:50mm
Charging: 5 V, 1A
1. Bluetooth Speaker
2. USB Charging cable
And audio cable
When using your Bluetooth Mobile Speaker, basic safety precautions
should always be followed, including the following:
3. User manual
“ ”
to charge when completely drained.
2. When charging, a red LED light will illuminate to indicate that the unit is
charging. The red light will turn off when your unit is fully charged.
1.
Previous:
Press and hold to access the
last track in playlist.Press to lower the volume.
2. Next:
Press and hold to access the next
track in playlist.Press to increase the volume.
4.Light Change
Short press this button to cycle through 5 light modes.
light flash with music mode.
3.ON/OFF Switch
You can plug one end of the included USB Charging
Cable into this jack, while plugging the other end into
a USB port on your computer in order to charge your
speaker’s built in lithium battery.
5. Charging Port/Aux-in
When Charging Your Speaker
Solid red LED = Charging
No red LED = Charge Complete
When Pairing Your Speaker to a Bluetooth Audio Source
Rapid blinking blue LED: Bluetooth not connected. (Ready to pair.)
Solid blue LED: Bluetooth connected.
3
Press and hold the“ ”for power on
Press and hold the“ ”again for power off
Under the playing music mode，you can press and
hold the light button to enter the
1.Power on,the Blue LED stay illuminated .
2.Plug in the supplied 3.5mm cable into the unit. The other end is connected
to your device.
3.The blue LED will blink slowly to indicated that you have entered Aux-In mode.
NOTE:
The internal battery of your speaker takes approximately two hours
When an iPhone or other smartphone is connected to your speaker follow
the steps below to take calls hands-free.
1. Press“ ”to pick up the call.
2. Press and hold to reject the call.
3. During call: Press“ ”twice to hang up the call.
“ ”
Using the Hands-Free Function
Pairing Bluetooth Devices to Your Speaker
1
2
4
5
the best
FCC ID:N7KB18P
Model Name:B18P