User Manual

ManualsBrandsKing ManualsRV AccessoriesJack Digital HDTV Over-the-Air Antenna — White

SPECIFICATIONS

Dimensions: 8.9” H x 16” W x 12” L

Weight: 2.62 lbs.

Frequency Bands: VHF (54-216 Mhz)

UHF (470-698 Mhz)

FM (87.9-107.9 Mhz)

Powered Amplier: +12 Volt / 100 mA

Power Supply: KING Power Injector (included)

Enclosure/Mount: ASA-Automotive grade

Signal Meter Frequency Response: 54-698 Mhz (Ch 2-51)

Low Prole Digital HDTV Over-the-Air Antenna

Owner’s Manual

OA8500 • White

OA8501 • Black

Roof Thickness: 1” to 4-1/2”

Roof Thickness: 4-1/2” to 8”

(when installed with KING extension #21850)

Thank you for choosing a KING Antenna!

CONTENTS

OPERATION and AIMING THE ANTENNA ......................................................... 1

CONTENTS and EXTENSION INSTALLATION ..................................................2

EXTERIOR BASE MOUNT INSTALLATION ....................................................... 3

INTERIOR ENCLOSURE INSTALLATION .......................................................... 4

POWER INJECTOR INSTALLATION .................................................................. 5

LIMITED WARRANTY ......................................................................................... 6

NOTE: Please read thru the installation instructions before beginning.

See page 2 for items supplied by the installer.

See page 5 for information on the MB8200 Mounting Plate

w/built-in KING SureLock

™

Digital TV Signal Meter

Summary of content (8 pages)

PAGE 1
Low Profile Digital HDTV Over-the-Air Antenna w/built-in KING SureLock™ Digital TV Signal Meter Owner’s Manual Roof Thickness: 1” to 4-1/2” Roof Thickness: 4-1/2” to 8” (when installed with KING extension #21850) OA8500 • White OA8501 • Black CONTENTS OPERATION and AIMING THE ANTENNA ......................................................... 1 CONTENTS and EXTENSION INSTALLATION .................................................. 2 EXTERIOR BASE MOUNT INSTALLATION ...........................................
PAGE 2
OPERATION AIMING THE ANTENNA 1. Turn on TV and power injector. 2. Turn on KING SureLock Signal Meter with switch on side of enclosure. 3. Press button and turn knob to rotate antenna in one direction until it hits the stop. 4. Rotate attenuator dial fully clockwise. Arrow on knob indicates which direction antenna is pointing. 5. Rotate antenna a full 360 degrees. Antenna will hit stop again. LEDs will illuminate from left (next to power) to right.
PAGE 3
CONTENTS IMPORTANT! For roofs 4-1/2” to 8” thick, install KING extension #21850. IMPORTANT! You must install the included wall mount power injector to operate the KING Jack antenna (see page 5). EXTENSION INSTALLATION ROOFS 4 1/2” to 8” THICK ONLY! Roofs thinner than 4 1/2” go to next page. If your roof is 4-1/2” to 8” thick you will need to install KING extension #21850. If using the extension, install it now, BEFORE INSTALLING BASE MOUNT ON ROOF.
PAGE 4
EXTERIOR BASE MOUNT INSTALLATION IMPORTANT! The installer is responsible for determining and supplying the most appropriate fasteners to secure the base mount to the roof and weatherproofing all holes with roof-compatible sealant. 1. Select an area on the roof for the base mount keeping in mind the following IMPORTANT POINTS: a) The antenna should be mounted with the coax channel towards the rear of the vehicle.
PAGE 5
INTERIOR ENCLOSURE INSTALLATION IMPORTANT! Before starting step 1, turn the adjustable connector (or extension if installed) in one direction until the antenna hits the stop. Now turn the connector all the way in the other direction until the antenna hits the stop again (slightly more than 360°). THE ANTENNA MUST ROTATE FREELY THRU THE ENTIRE DISTANCE. 1. Press knob button and remove knob from enclosure base. 2. Route the coax thru the coax hole in the enclosure base.
PAGE 6
POWER INJECTOR INSTALLATION The Wall Mount Power Injector: • Can be mounted in most standard electrical boxes. • Requires a +12 Volt DC power source. (Inadequate voltage may cause the green LED to not illuminate and the unit to not function properly. • Requires #10-12 female spade connectors for power and ground connections. • Has an internal fuse rated @ 400 mA max. If tripped, the fuse will reset when the circuit cools. • Is not an amplifier. No devices other than those shown below should be connected.
PAGE 7
LIMITED WARRANTY IMPORTANT! Do not power wash any part of the KING Jack antenna head or base mount. Every new KING Jack HDTV Antenna System is thoroughly inspected and tested before leaving the factory, and is covered by the following four-year parts and one-year labor limited warranty from the date of original purchase: • Four-year parts warranty: The customer is not responsible for the cost of replacement parts if the original part is determined to be defective under the terms of the warranty.
PAGE 8
Simply better, by design.™ 11200 Hampshire Avenue South, Bloomington, MN 55438 PH 952.922.6889 || FAX 952.922.8424 || kingconnect.